AuviTran AVDT-BOB Bedienungsanleitung

AVDT-BOB User’s manual v1.6 Page 1 / 25

AVDT-BOB

User’s manual

www.auvitran.com

AVDT-BOB-AE4io

AVDT-BOB-AE8io

AVDT-BOB-AS8io

AVDT-BOB-ADE8io

AVDT-BOB-AEG6io

AVDT-BOB-ADX8io (Rear)

AVDT-BOB-ADX8io (Front)

AVDT-BOB User’s manual v1.6 Page 2 / 25 
 
Table of contents 
Legacy...............................................................................................................3 
1 LIMITATION OF LIABILITY .............................................................................3
2 TRADEMARKS .............................................................................................3
3 COPYRIGHT .................................................................................................3 
4 MORE INFORMATION...................................................................................3
2AVDT-BOB Quick Start........................................................................................4 
1 Power to Start-up.........................................................................................4
2 Connect the AVDT-BOB to an IP/Dante network ...............................................4
3 AVDT-BOB’s Dante settings...........................................................................5
4 Access to AVDT-BOB’s User Interface via AVSMonitor on Windows OS ..............6
5 Access to AVDT-BOB’s User Interface via a Browser........................................7
3AVDT-BOB architecture.......................................................................................8 
1 AVDT-BOB inputs and outputs........................................................................8
2 AVDT-BOB architecture ................................................................................8
3 AVDT-BOB’s schematic .................................................................................9
4 Input processing block..................................................................................10 
5 Mixing Processing block ...............................................................................11 
6 Output processing block...............................................................................11 
4AVDT-BOB User’s Interface ...............................................................................12 
1 Bar menu for interface selection ...................................................................12 
2 Inputs interface ..........................................................................................12 
3 Mixers’ interface .........................................................................................13 
4 Outputs’ interface .......................................................................................14 
5 Processing interface....................................................................................15 
5.1 EQ Processing view...............................................................................16 
5.2 Limiter/Compressor view........................................................................17 
6 Parameter interface ....................................................................................17 
6.1 General software setting menu ...............................................................18 
6.2 Network parameters menu .....................................................................18 
6.3 Save/Load parameter menu ....................................................................18 
6.4 GPIO menu (available for AVDT-BOB-ADE8io/ADX8io ................................20 
6.4.1 GPIO in GPI Mode ...........................................................................21 
6.4.2 GPIO in GPO Mode..........................................................................22 
6.4.3 GPIO in Fader Mode ........................................................................23 
5GPIO wiring for AVDT-BOB-ADE8io or AVDT-BOB-ADX8io ....................................24 
1 GPIO Connection for “GPI” mode...................................................................24 
2 GPIO Connection for “GPO” mode .................................................................25 
3 GPIO Connection for “Fader” mode................................................................25 
 

AVDT-BOB User’s manual v1.6 Page 3 / 25

1. Legacy

1.1 LIMITATION OF LIABILITY

In no case and in no way, the provider of this software (AuviTran, the distributor or

reseller, or any other party acting as provider) shall be liable and sued to court for damage,

either direct or indirect, caused to the user of the software and which would result from an

improper installation or misuse of the software. “Misuse” and “improper installation” mean

installation and use not corresponding to the instructions of this manual.

AuviTran is constantly working on the improvement of the products. For that purpose, the

products functionalities are bound to change and be upgraded without notice. Please read

carefully the User’s manual as the new functionalities will be described therein.

1.2 TRADEMARKS

All trademarks listed in this manual are the exclusive property of their respective owners.

They are respected “as is” by AuviTran. Any use of these trademarks must receive prior

approval of their respective owners. For any question, please contact the trademark’s

owner directly.

1.3 COPYRIGHT

The information in this manual is protected by copyright. Therefore, reproduction,

distribution of whole or part of this manual is strictly forbidden without the prior written

agreement of AuviTran.

1.4 MORE INFORMATION

Please visit our website for any question of further inquiry concerning our product range.

Updates will also be posted when available.

http://www.auvitran.com

AVDT-BOB User’s manual v1.6 Page 4 / 25

2AVDT-BOB Quick Start

2.1 Power to Start-up

To start your AVDT-BOB, connect the Main port of your AVDT-BOB, to an active POE

switch port using a CAT5E/6 cable (Gigabit connection) or alternatively connect an optional

12V DC power to the DC Power connector of your AVDT-BOB.

POE Port (Main)DC Plug

Power LED Power LED

POE Port (Main)DC Plug

When powered, the Green Power led of the AVDT-BOB will be On.

Notice: You can use at the same time the POE and 12VDC and they will act as redundant

power supplies.

2.2 Connect the AVDT-BOB to an IP/Dante network

The connection of your AVDT-BOB to the IP/Dante network can done via Ethernet

CAT5e/6/7 cables using the Main Gigabit port that is POE compatible or via the Aux Gigabit

port(s)

When connected to another active/running Ethernet device (Switch, Mac, PC, IP router),

the Link LED of the connected port will be On and the Act LED will start flashing.

AVDT-BOB can be daisy chained to other Dante device via the remaining port(s) thanks to

an internal gigabit switch that connects:

-Physical Ethernet ports (Main, Aux)

-Dante component

-User Interface of ARM processor managing Web 2.0, DSP and Mic preamps

AVDT-BOB has 2x independent IP network addresses and 2 associated names to control

“Dante”functions and “User-Interface”:

IP addresses are set automatically by default via a DHCP server or using APIPA

addresses (169.254.xxx.xxx/16).

The Dante name of an AVDT-BOB may be changed by the Dante Controller. This

name is preset at factory at “AVDT-BOB-#” where # is its serial number.

AVDT-BOB serial number 145 has Dante name “AVDT-BOB-145” as

factory preset.

The name of User Interface of an AVDT-BOB is its Dante name plus a fixed

extension “-UI”. This name is preset at factory to “AVDT-BOB-#-UI” where # is its

serial number.

AVDT-BOB with serial number 145 has User Interface name “AVDT-BOB-

145-UI” as factory preset.

AVDT-BOB User’s manual v1.6 Page 5 / 25

2.3 AVDT-BOB’s Dante settings

The AVDT-BOB Dante settings are done via the standard Audinate Dante Controller.

Download Dante Controller on the Audinate web site at the following web address

https://www.audinate.com/products/software/dante-controller.

Install Dante Controller by double clicking on the download file.

Start Dante Controller to detect your AVDT-BOB Dante devices and control

settings:

To change AVDT-BOB name, Double click on the device label

Select “Device Config” tab in the new windows and modify the “Rename Device” field

Consult the Audinate Dante Controller User’s manual for any other information

Notices: Using the Dante controller, it is possible to run commands by setting specific

Dante names in an AVDT-BOB (all command name must be filled with the maximum of ‘x’ at

end):

-Setting AVTxCMD-GIPxxxxxxxxxxxxxxxxxxxx as Dante Name in an AVDT-BOB will request

to get back the IP address of the AVDT user Interface. In reply the Dante Name of the

module will be changed back to AVTxANS-GIP-a-b-c-dxxx..xxx where a.b.c.d is the IP

address of user interface (AVTxANS-GIP-169-254-0-145xxxxxx for instance)

-Setting AVTxCMD-FIP-192-168-0-222xxxxxx as Dante Name for an AVDT-BOB will set its

IP address to 192.168.0.222. When done, the device returns to its previous name

-Setting AVTxCMD-FFSxxxxxxxxxxxxxxxxxxxx as Dante Name for an AVDT-BOB will request

to call back parameters from factory settings and to reset the AVDT-BOB

AVDT-BOB User’s manual v1.6 Page 6 / 25

2.4 Access to AVDT-BOB’s User Interface via AVSMonitor on Windows OS

The AVDT-BOB User Interface can be accessed using AVSMonitor on Windows OS:

Download AuviTran AVS-Monitor free software for windows 7/8/10 available at the

following web address http://www.auvitran.com/w4/?page_id=86

Install AVS-Monitor by double clicking on the download file.

Start AVS-Monitor.

The AVDT-BOB connected to the network will automatically appears in 2 lists on left:

▪“Network controller” provides access to the AVDT-BOB control

▪“Dante Network” give “Dante” information on the AVDT-BOB

Select the AVDT-BOB in the left list called “Network controller” and” “Control” Tab in

the right windows as describe bellow.

See chapter 3 for interface description.

Notices:

-If your device doesn’t appear, your network configuration is probably not good.

1) Go to the AVS-Control-Panel using “Edit/Control panel” menu or press Ctrl+P

2) Select a valid network adapter in the “Dante / AuviTran Adapter”

3) Press the “Turn On” button if the service is off (red LED).

-The “Properties Tab” provides the IP address of the AVDT-BOB user’s interface

-You can transfer the control of your device to

your standard browser by a right click on AVDT-

BOB name in the Network list and selected

“Open on new window”

-For more information on AVSMonitor read its “User’s manual”

AVDT-BOB User’s manual v1.6 Page 7 / 25

2.5 Access to AVDT-BOB’s User Interface via a Browser

The user interface of an AVDT-BOB can be launched without installation by any standard

Web browser compatible with HTML5 and JavaScript standards.

The device hosting the web browser must comply with the following:

-May be any platform PC, Laptop, Tablet, Smartphone working whatever OS

(MacOS, iOS, Android, Windows, Linux …) with a minimum resolution of 800x600

or 600x800

-Must be connected to the same IP network than the AVDT-BOB to control it

-It can use WIFI or Ethernet link

To launch the user interface of an AVDT-BOB using a browser

Start a Web Browser (i.e. Safari, Firefox, Chrome, Opera…)

Write the User Interface Name (see §2.2) terminated by “.local” in Web Browser

address field/bar to ask it accessing to the IP server with a local name in your local

area network (“.local” at the end is needed to force mDNS local name in the

browser)

“AVDT-BOB-145-UI.local” for instance to connect to AVDT-BOB serial

number 145 if the Dante name was not changed

The Browser will display AuviTran’s Logo during the loading of the user’s interface.

After loading you will see the interface of the AVDT-BOB User interface as Follows

(iPad/Safari and iPad/Firefox).

See chapter 3 for a description of the AVDT-BOB User’s interface.

Notices:

-IE and Edge on Windows OS does not manage the “.local” and mDNS name. Use

the IP address of the User’s Interface for this web Browser or follow instructions

given in §2.4 notices to run web browser directly from AVSMonitor.

-If you have problem with the UI name, remember you can change it using Dante

controller.

AVDT-BOB User’s manual v1.6 Page 8 / 25

3AVDT-BOB architecture

3.1 AVDT-BOB inputs and outputs

The AVDT-BOB-AE8io and AVDT-BOB-AS8io have 4 analog balanced Mic/Line inputs and 4

balanced analog outputs on Euroblock/SUBD connectors. They can receive and send 4

digital signals from/to Dante from their Main or Aux gigabits Ethernet ports.

The AVDT-BOB-AE4io has {2} analog balanced Mic/Line inputs and {2} balanced analog

outputs on Euroblock connectors. It can receive and send 4 digital signals from/to Dante

from its Main or Aux gigabits Ethernet ports.

These input / output signals are named as follows in these AVDT-BOB:

-Mic/Line1-4{2} for the signals coming from Mic/Line inputs

-Dante In1-4 for the signals coming from Dante network

-Line Out1-4{2} for the signals sending to Line outputs

-Dante Out1-4 for the signals sending to Dante network

The AVDT-BOB-ADE8io and AVDT-BOB-ADX8io have 2 analog balanced Mic/Line inputs +

an AES/EBU input and 2 balanced analog outputs + an AES/EBU output on

Euroblock/XLR/SUBD connectors. They can receive and send 4 digital signals from/to Dante

from their Main or Aux gigabits Ethernet ports.

These input / output signals are named as follows in these AVDT-BOB:

-Mic/Line1-2 for the signals coming from Mic/Line inputs

-AES/EBU ch1-2 for the signals coming from AES/EBU input

-Dante In1-4 for the signals coming from Dante network

-Line Out1-2 for the signals sending to Line outputs

-AES/EBU ch1-2 for the signals sending to AES/EBU output

-Dante Out1-4 for the signals sending to Dante network

3.2 AVDT-BOB architecture

The AVDT-BOB architecture is divided in 3 main interconnected blocks:

-The Input block manages Mic/Line1-4{2} preamps, {AES/EBU ch1-2} and Dante in1-4.

It sends DirectOut MicLine1-4{2}, {AES/EBU ch1-2} to Output Processing Block. It

computes processed Mic/Line1-4{2], {AES/EBU ch1-2} and 4 processed Dante inputs

for the Mixing and Output Processing Blocks.

-The Mixing block receives the processed Mic/Line1-4{2}, {AES/EBU ch1-2} and

Dante1-4. It mixes them on 4 independent mixers to provide mixing Master1-4 to

Output Processing Block.

-The Output block enables selecting the source Out1-4{2}, {AES/EBU ch1-2} and

Dante Out1-4 from DirectOut Mic/Line1-4{2}, {AES/EBU ch1-2}, Processed

Mic/line1-4{2}, {AES/EBU ch1-2}, Processed Dante1-4 and the Master1-4. Once the

source selection done it processes Line and Dante outputs.

AVDT-BOB User’s manual v1.6 Page 9 / 25

3.3 AVDT-BOB’s schematic

Analog Inputs

Mic/Line1-2

Input Processing

Output Processing

Analog Outputs

Line_Out1-2

Dante Outputs

Dante_Out1-4

Mixing

Processing

Direct Out

Mic/Line1-2

Processed

Mic/Line1-2

Dante Inputs

Dante_In1-4

Mixing

Master1-4

Processed

Dante1-4

Analog Inputs

MicLine1-4

Input Processing

Output Processing

Analog Outputs

Line_Out1-4

Dante Outputs

Dante_Out1-4

Mixing

Processing

Dante Inputs

Dante_In1-4

Mixing

Master1-4

Direct Out

Mic/Line1-2

Processed

Mic/Line1-2

Processed

Dante1-4

AVDT-BOB-AE4io’s schematic AVDT-BOB-AE8io/AS8io’s schematic

Analog Inputs

MicLine1-4

Input Processing

Output Processing

Analog Outputs

Line_Out1-4

Dante Outputs

Dante_Out1-4

Mixing

Processing

Mixing

Master1-4

Direct Out

Mic/Line1-2

Processed

Mic/Line1-2

Mic/Line + Digital

Input 1-4

Input Processing

Output Processing

Analog + Digital

Output1-4

Dante Outputs

Dante_Out1-4

Mixing

Processing

Dante Inputs

Dante_In1-4

Mixing

Master1-4

Direct Out

1-4

Processed

Input 1-8

AVDT-BOB-AEG6io’s schematic AVDT-BOB-ADE8io/ADX8io’s schematic

AVDT-BOB User’s manual v1.6 Page 10 / 25

3.4 Input processing block

The Input Processing controls the analog mic preamps, the +48V phantom power of

Mic/Line inputs and the digital gains for Dante inputs, manages the digital signal processing

(Phase inversion, Mute, Equalization, Limiter/Compressor/Gate) for the Mic/Line or

AES/EBU inputs or Dante inputs.

There are 4 (EQ + Dyn) processing* blocks available for the Input Processing. Each one be

individually connected to its respective Mic/Line or AES/EBU input or Dante input.

Mic/Line1-4{2}

+48V

Mic Preamp

fader

Dante In1-4

Dante fader

4 {2}

On / Off

DirectOut

1-4{2}

Processed

input1-4{2}

Processed

Dante1-4

Meter

Input

Processing*

(EQ + Dyn)

Processing on Dante

+48V

Diagram of the AVDT-BOB's Input Processing block for AE4io/AE8io/AEG6io/AS8io versions

Mic/Line1-2

+48V

Mic Preamp

fader

Dante In1-2

Dante fader

On / Off

DirectOut

1-2

Processed

input1-2

Processed

Dante1-2

Meter

Input

Processing*

(EQ + Dyn)

Processing on Dante 1-2

+48V

AES/EBU ch1-2

Dante In3-4

Dante fader

On / Off

DirectOut

3-4

Processed

input3-4

Processed

Dante3-4

Meter

Input

Processing*

(EQ + Dyn)

Processing on Dante 3-4

Diagram of the AVDT-BOB's Input Processing block for ADE8io/ADX8io

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AuviTran Signalprozessor Handbücher

AuviTran

AuviTran AVDT-BOB-AE810 Bedienungsanleitung

Beliebte Signalprozessor Handbücher anderer Marken

2Y-LINK Technology

2Y-LINK Technology CI-12-ASP-DAASS Bedienungsanleitung

Crane Song

Crane Song Falcon Bedienungsanleitung

Steg

Steg DSP 6 Bedienungsanleitung

Rocktron

Rocktron INTELLIFEX LTD Bedienungsanleitung

RF-Lambda

RF-Lambda RF1457 Bedienungsanleitung

TC Electronic

TC Electronic DB8 MKII Handbuch

Acqiris

Acqiris U5309A Bedienungsanleitung

PCI

PCI MicroTrans EQ Handbuch

Crestron

Crestron Avia DSP-1282 Bedienungsanleitung

turck

turck MS96-11EX0-R/24VDC Bedienungsanleitung

ESX

ESX QUANTUM QL810SP Bedienungsanleitung

Rolls

Rolls ROTORHORN RP147 Bedienungsanleitung

Oberheim

Oberheim GM-1000 Bedienungsanleitung

AMC

AMC DSP8X8 Bedienungsanleitung

Planet Audio

Planet Audio PC3.5B Bedienungsanleitung

Behringer

Behringer Super-X Pro CX3400 Bedienungsanleitung

Euphonix

Euphonix DF64 Digital Frame Bedienungsanleitung

Lem Elettronica

Lem Elettronica DSP30-4G Bedienungsanleitung