Avalon SteriTech GAMBIT Bedienungsanleitung

Quick

Start

Guide

Machine Overview 03

Charging Instructions 04 - 05

Solution Filling & Draining 06 - 07

Machine Setup with Whiz 08 - 09

Operation Modes 10

Maintenance 11

Filler port ﬁlter

Solution ﬁller door

Housing enclosure

Solution tank

Swivel casters (x4)

Solution drainage tube

Solution drainage door Bottom latch hold

down knob

Motion sensor

assembly

Motion

sensor light

Motion

sensor lens

Drainage valve

Bottom latch

Gambit system

power button

Solution level

indicator LED light

Charging port cover

Power Charging Part

Side latch (Left)

Spraying nozzle manual

activation button

Spraying nozzle

Battery level

indicator LED light

Side latch (Right)

Machine Overview

1. Attach the power cord to the power charger

2. Check to ensure the voltage selector on the power

charger is properly set to 110V or 230V and power

button on the power charger is in the oﬀ position

3. Attach the power cord to the wall outlet

4. Detach the charger port cover from the Gambit

system, then align and insert the charger

connector into the Gambit system

5. Check the connection between the Gambit

system and the charging connector by pulling

the connector lightly. It should stay connected

6. Switch on the power button on the power

charger. The power charger LED indicator light

should be on

On/O

Voltage

Selector

Charging Instructions

7. To stop charging, switch oﬀ the power charger

by pressing the power button to the oﬀ position

8. Press and hold the eject button on the Gambit

system. Gently pull on the power cord connector

to remove the charging connector

9. Unplug the power charger from the wall outlet

Eject Button

1. The Gambit system should be switched oﬀ and

detached from Whiz

2. Ensure the Gambit system is not connected

to the power charger

3. Drain the solution tank until it is empty. Then

turn the drainage valve to its closed position

4. Flip open the solution ﬁller door

5. Slowly ﬁll the Gambit system with approved chemicals /

disinfectants through the ﬁller port ﬁlter

(Maximum capacity : 3 L)

6. Close the solution ﬁller door ﬁrmly after ﬁlling

Solution Filling & Draining

Filling Instructions

Closed

Drain

1. The Gambit system should be switched oﬀ

and detached from Whiz

2. It is not connected to the power charger

3. Open the magnetic solution drainage door

4. Take out the solution drainage tube and insert

into an appropriate container. Rotate the drainage

valve anticlockwise by 90 degrees to drain

5. After drainage is completed, rotate the drainage

valve clockwise by 90 degrees to close. Tuck away

the solution drainage tube

6. Close the magnetic solution drainage door

Solution Filling & Draining

Draining Instructions

1. Check that the bottom latch hold-down knob

is in the unlocked position

2. Ensure Whiz is switched on

3. Align the Gambit with Whiz, hold the top part

of Whiz with one hand and hold Gambit with

another hand, and push the two units together

4. Lift the Whiz handle slightly to let the top housing

of Gambit pass under handle and then release

the handle to its resting position

5. An audible “click”Should be heard when the two

appliances are assembled

6. Gently push & pull the Whiz & Gambit to test

whether they are assembled securely

Machine Setup with Whiz

Assembly Instructions

Machine Setup with Whiz

1. Ensure the Whiz handle is down

(with auto brake engaged)

2. Lift bottom latch up and rotate the bottom latch

hold-down knob in a counter-clockwise fashion

3. Press and hold both side latches

4. Pull the Gambit system backwards to decouple

from the Whiz

5. Reset the Gambit system’s bottom latch

by rotating the bottom latch hold-down knob

in a clockwise fashion

Disassembly Instructions

1. Set the nozzle angle via the handle before operation

2. Ensure the Whiz is switched on and couple

the Gambit system to Whiz

3. Turn on the Gambit system by pressing

the power button

4. Wait 50 seconds for the Gambit system’s automatic

boot up sequence to initiate. A white light will be

seen when boot up sequence is completed

6. If you want to manually override the automatic

system, press the spraying nozzle manual button

5. The preset mode is the automatic mode

>10s of movement: start spraying

>10s of stationary idle: stop spraying

Power

Spray

Operation Modes

Inhaltsverzeichnis

Beliebte Reinigungsgeräte Handbücher anderer Marken

Skov

Skov Farm AirClean Handbuch

Nilfisk-Advance

Nilfisk-Advance CA 240 Bedienungsanleitung

ORBOT

ORBOT LiO Bedienungsanleitung

unGer

unGer OmniClean Bedienungsanleitung

CENTREGO

CENTREGO Toucan Eco Bio Carry Bedienungsanleitung

BANDELIN

BANDELIN SONOREX TECHNIK RM 110 UH Bedienungsanleitung

Sealey

Sealey VMA913 Bedienungsanleitung

Aztec

Aztec 520-00 Bedienungsanleitung

BÖWE

BÖWE P25 Bedienungsanleitung

Tunap

Tunap MF 929 Bedienungs- und Montageanleitung

RIDGID

RIDGID K-45AF-7 Bedienungsanleitung

Aircraft

Aircraft POWERGLIDE Bedienungsanleitung

Suevia

Suevia 130.5011 EASYCLEANER Bedienungsanleitung

Streamline

Streamline Filterplus MOBI SK Bedienungsanleitung

Thermax

Thermax AF2 Bedienungsanleitung

IPC

IPC CT15R Bedienungsanleitung

i-MO

i-MO Öko 2000 Bedienungsanleitung

unGer

unGer Hydro Power Ultra UNP01 Bedienungsanleitung