Avanti ZeroWater ZJ003IS Bedienungsanleitung
USE AND CARE 1
OWNER’S MANUAL FILTER BOTTLE FOR STANDARD COOLERS
MEASURE AND
TASTE THE
DIFFERENCE!
000
2 USE AND CARE
000
MEASURE AND
TASTE THE
DIFFERENCE!
Bottled
1 2 4
Conventional Filtered
Tap
210
ZeroWater
000
07 6
124
21 0
Sample readings may vary. Test for yourself.
“000” =
FDA Standard for TDS
in Puried Water*
USE AND CARE 1
Congratulations on your purchase
of a new ZeroWater®Filter Bottle!
Be prepared to taste the BEST tasting water like never before – we
guarantee it! Your 5-Stage ZeroWater® lters are guaranteed to remove
virtually all dissolved solids from your tap water. To nd out more about
Zero Technologies, please visit www.zerowater.com.
Included in this brochure are simple instructions to help you assemble and
maintain your ZeroWater®Filter Bottle. Now you’ll be able to start converting
your own tap water into ZeroWater®!
IMPORTANT!
Should you experience any difculties with water lters, before returning the
product to the store, please call Customer Service toll free 24 hours a day, 7 days a
week at 1-800-503-2939. Most issues can be resolved with a short phone call to our
trained professionals.
SAFETY PRECAUTIONS
Do not use with water that is microbiologically unsafe or of unknown quality without
proper disinfection before or after the system. Individuals requiring water of specic
microbiological purity should consult their physician. Unless notied otherwise,
municipal water is potable. The contaminants or other substances removed or
reduced by this water treatment device are not necessarily in your water.
PROPER INSTALLATION
Please read all instructions, specications, and precautions before installing and using
your water ltration system.
* Filtered potable tap water tested by an independent lab (not the FDA) to meet specically the water quality
requirements for using the label “puried”. Compared to water produced by leading gravity fed lters.
Don’t forget to register your ZeroWater®Filter Bottle.
Details are included on the enclosed Registration Card.
www.avantiproducts.com
2 USE AND CARE
IMPORTANT!
Please read before rst use.
If you are using a water cooler with this product, please read this! Our ZeroWater
®
Filter Bottle ts most standard water coolers AFTER the splash guard is removed!
If the splash guard is not removed, the oat valve on the ZeroWater
®
Filter Bottle
will not work and will cause your water to spill!
DIRECTIONS FOR REMOVING THE SPLASH GUARD
If you look into the reservoir you’ll see the splash guard with a spike, used to pierce
a hole in the cap of bulk water containers. Grip the splash guard, turn it counter
clockwise and pull up on it. This should remove the splash guard from the water
cooler. If you have further questions about this process with your particular model,
you may need to refer to your user’s manual. If you still need assistance, please call
our Customer Service number.
Patents: 5,635,063; 6,572,769; 7,276,161; 7,413,663; Additional patents pending.
If you are using the Avanti
Water Dispenser
Model WDTZ000
Simply remove the ring as
shown. (Only if provided on
your model).
If you are using any other
standard water dispenser
remove the entire splash
guard assembly as
shown.
USE AND CARE 3
Patents: 5,635,063; 6,572,769; 7,276,161; 7,413,663; Additional patents pending.
RECYCLING
Filtering your water through ZeroWater® lters not only improves the taste of your
tap water, it also prevents you from throwing plastic water bottles into the trash and
clogging up landlls. Zero Technologies, LLC is proud to be the only major company
that recycles gravity lter cartridges from U.S. customers.
If you wish to participate in this program, you will need to do a few simple
steps to be sure the lters returned are processed accurately for recycling.
Visit
www.zerowater.com/recycling
to download a form. Place your used lter
into a sealable plastic bag and be sure it is sealed tightly. Place your used
lters and your completed form in a well packed box and mail to the following
address:
Zero Technologies, LLC
4510 Adams Circle
Unit F
Bensalem, PA 19020
Make sure to clearly mark your package
“ATTN: RECYCLING PROGRAM”.
When the lter reaches us, the plastic as well as the materials inside it
will be separated and sent to various facilities for reuse. We are asking
customers to pay for shipping their exhausted lters to us. Additional
information on this program, including discounts on future purchases, can be
found at www.zerowater.com/recycling.
If you have any questions about this program, please call the ZeroWater®
customer service hotline 24 hours a day: 1-800-503-2939
4 USE AND CARE
LID
UPPER CHAMBER
FILTER CARTRIDGE
LOWER CHAMBER
FLOAT VALVE WITH
SOFT WASHER
LOWER CHAMBER
DIVIDER RIM
MAXIMUM
WATER LEVEL
FILTER ADAPTER
(NOT SHOWN)
USE AND CARE 5
ZeroWater®Filter Bottle
Use and Care Instructions
Please read before rst use.
INSTRUCTIONS BEFORE INSTALLING CARTRIDGE
AND FIRST USE
1. Clean all plastic components and lter cartridges by washing and rinsing
thoroughly with warm water only. Rinse the Filter Bottle thoroughly when
washing with soap.
2. Note: the Filter Bottle components, lter cartridges and TDS meter are not
dishwasher safe.
3. Discard all plastic bags. This may be a suffocation hazard to young children.
ASSEMBLY
1. Take the lower chamber and place the lower chamber
divider rim rmly on the top. The rippled part of the white
rim should be overlapping the lower chamber. If assembled
upside down, there will be leakage. Be sure it ts tightly
on the lower chamber (see ZeroWater
®
Filter Bottle
components
on page 4).
2. Align the nut (included) into the recessed area at the inner
bottom of the lower chamber and screw the oat valve
tightly through the hole on bottom of lower chamber (inset
A).
Do not prop the Filter Bottle on the oat valve once
assembled, as it is fragile and will break.
3. Place the lower chamber on top of your cooler with the oat
valve tting inside the cooler’s reservoir (see Using Your
ZeroWater
®
Filter Bottle with a Standard Water Cooler on
page 6).
4. Install lter cartridges now, using steps 1 through 3 from
instructions on next page.
5. Place the upper chamber on top of the lower chamber. Be
sure that the lower chamber divider ring is tightly afxed
around the lower chamber (see ZeroWater
®
Filter Bottle
components on page 4).
6. Place the lid on top of the upper chamber.
A
6 USE AND CARE
INSTALLATION OF FILTER CARTRIDGES
1. Install the lter adapter to the upper chamber by turning
clockwise until you feel a tight and secure t.
Ensure the “O-Ring” is in place and not bulging outward.
2. Remove lter cartridges from packaging.
3. Tightly screw cartridges into the holes on the bottom side of the adapter to
obtain a complete seal with the O-ring. Do not over-tighten as the O-ring will
become warped and not seal completely allowing unltered water to leak to the
lower chamber and your water will not read “000”(see ZeroWater
®
Filter Bottle
components on page 4).
4. Place upper chamber with attached lter cartridges back onto the lower chamber
divider rim of the lower chamber (see ZeroWater
®
Filter Bottle components on
page 4).
If new lters are exposed to cold temperatures for prolonged periods, keep lters at
room temperature for several hours before passing water through the rst time.
USING YOUR FILTER BOTTLE WITH A STANDARD
WATER COOLER (sold separately)
1. Unplug your cooler.
2. Drain all water from the cooler using the spigots and the drain plug in the back
of the cooler. Using a cooler without water in it, when plugged in, can cause it
to smoke and break. Make sure you secure the drain plug when you are nished
draining the cooler.
3. Be sure you have removed the splashguard from the cooler reservoir. Refer to
page (2) for directions.
4. Clean the reservoir and spigots by mixing 1 tablespoon of baking soda into 1
gallon of hot water and pouring the solution directly into the cooler reservoir.
5. Let solution sit for about 30 minutes and then drain through spigots and drain
plug.
6. Flush the cooler with three gallons of plain hot water using same method. Secure
the drain plug. The total capacity of the bottom chamber is three gallons.
7. Do not replace the splashguard or spike xture.
8. Now your cooler is ready for your assembled ZeroWater
®
Filter Bottle. Add water
before plugging cooler back into electrical outlet (See step 6 under section “Filling
the ZeroWater
®
Filter Bottle with Tap Water on page 7).”
USE AND CARE 7
FILLING THE FILTER BOTTLE WITH TAP WATER
1. Remove lid.
2. Slowly ll the upper reservoir with cold tap water. Be careful not to dump
water too quickly into the upper chamber when the lower chamber is
empty because
it may tip and spill.
3. Allow water to pass from the upper chamber through the lters to the
lower chamber. Water will be ready to drink in several minutes.
4. Test the water using the TDS meter to conrm a “000” reading.
5. If it doesn’t read “000”, ush the water out, check all connections and
seals.
6. Pour water through.
7. Do not over ll. The rst time you ll your Filter Bottle it will take extra
water to ll the cooler reservoir. When water in the lower chamber
reaches the line marked “MAXIMUM WATER LEVEL”, do not put any
more water in the upper chamber, as it may leak. The upper chamber is
not designed to be a long term reservoir.
Safety Precautions: Do not use with water that is microbiologically unsafe
or of unknown quality without proper disinfection before or after the
system. Individuals requiring water of specic microbiological purity should
consult their physician. Unless notied otherwise, municipal water is
potable.
1
2
3
4
5
Most conventional carbon lters only
lter certain substances from your water.
ZeroWater® 5-Stage Filters remove 99.6%
of total dissolved solids based on an EPA
certied lab test, while
conventional 2-Stage Filter remove less than
50%.
STAGE 1
Activated carbon infused micron cloth
STAGE 2
Multi-layer system using activated
carbon and oxidation reduction alloy
STAGE 3
Distributor that maximizes contact time
STAGE 4
Comprehensive ION EXCHANGE array
STAGE 5
Non-woven membrane to remove
ne particles
It is essential to change the lters with
a reading of “006” on the included TDS
meter in order for the product to continue
to perform as represented. The longevity
of the lter may vary based on local water
conditions. Under laboratory protocols, a
single lter was rated for 22.5 gallons in the
certication process.
The contaminants or other substances
removed or reduced by this water treatment
device are not necessarily in
all users’ water.
Patented Ion Exchange Filter
* Filtered potable tap water tested
by an independent lab (not the
FDA) to meet specically the water
quality requirements for using the
label “puried”. Compared to water
produced by leading gravity fed lters.
Inhaltsverzeichnis
Sprachen:
Andere Avanti Wasserfiltersystem Handbücher
Beliebte Wasserfiltersystem Handbücher anderer Marken
Gaggenau
Gaggenau BRITA INTENZA 467873 Bedienungsanleitung
Brita
Brita SAFF-100 Bedienungsanleitung
HEISSNER
HEISSNER FPU24000-00 Bedienungsanleitung
BGS technic
BGS technic 1518 Bedienungsanleitung
Reverse Osmosis
Reverse Osmosis RF Series Bedienungsanleitung
ubbink
ubbink Filtramax Series Bedienungsanleitung