Avaya P333T-PWR Bedienungsanleitung

Avaya P333T-PWR

Quick Start Guide

Unpack

Rack mount (optional)

Connect the cables

Configure

Run Web-based

Manager (optional)

Power up

Unpack

Check the package contents for the following:

LIf any items are missing or damaged, contact your supplier.

Equipment

• One Avaya™ P333T-PWR Inline power Layer 2 Workgroup Switch

• One AC power cable

• One RJ-45 to DB-9 serial adapter cable

• Four rubber feet

• Four screws with washers for rack mounting

LEthernet connection cables are not supplied

Documentation

• Avaya P333T-PWR Quick Start Guide (this document)

• Avaya P330 Release Notes

• Avaya P330 Documentation and Utilities CD (see detail below)

• Avaya Warranty and License Agreement

Avaya P330 Documentation and Utilities CD

The CD contains the latest User's Guides for the Avaya P330 stackable switches and files for

use with the Embedded Web Manager.

User's Guides

You can view and print these Guides using Adobe® Acrobat® Reader.

Auxiliary Files for use with the Embedded Web Manager

Please refer to the documentation for information on how to use these files.

• Java plug-in

• Help files

Adobe Acrobat Reader

This application allows you to view and print the User's Guides on this CD.

Rack mount (optional)

1. Snap open the hinged ends of the unit’s front panel to reveal the screw holes.

2. Position the unit in the rack.

3. Secure the unit to the rack, taking care not to overtighten the screws.

4. Snap closed the hinged ends of the front panel.

LYou can now safely connect the cables to the unit.

WARNING: Disconnect all cables from the unit before proceeding with the rack

installation. In order to isolate the P333T-PWR completely, you must disconnect all

power inputs.

P333T

EXPANSION

SLOT

FDX

FIV

COLLNK

Tx Rx

LAG

HspdFC

SYS

OPR PWR

11 12

13 14 15 16 17

LAG

234 5

CONSOLE

2118 19 20 2322 24

LAG

78 1110

LAG

P333T

EXPANSION

SLOT

FDX

FIV

COLLNK

Tx Rx

LAG

HspdFC

SYS

OPR PWR

11 12

13 14 15 16 17

LAG

234 5

CONSOLE

2118 19 20 2322 24

LAG

78 1110

LAG

Closed hinged end

Open hinged end

Screw

holes

Power up

AC Input

1. Insert the power cord into the power connector (BUPS or Power Supply) on the rear of the

unit.

2. Insert the other end of the power cord into the electricity supply or the connector on the

BUPS.

XThe unit powers up and performs a self test procedure. The LEDs flash at regular

intervals after the self-test procedure is completed successfully.

DC Input (Optional)

The P333T-PWR an operate on the AC input only. However, you may wish to use the optional

DC input for the following:

• Backup for the Power over Ethernet ports

• To provide more than 200W for the Power over Ethernet ports

LPlease refer to the P333T-PWR User’s Guide for more information.

BUPS connector

AC connector

DC connector

FIV – Force Initial Version (see Avaya P330

User’s Guide)

LNK – When ON, link is OK

COL – When ON, indicates a collision on the

port in HDX mode

Tx, Rx – Shows traffic activity for

transmitted and received packets

FDX – Shows Full/Half Duplex mode

FC – When ON, Flow Control is enabled for

a port in FDX mode

Hspd – Shows speed of port (10 Mbps or

100/1000 Mbps)

LAG – When ON, the port is included in a

Link Aggregation Group (LAG).

InPWR – Shows Inline power status

SYS – Shows whether this module is the

Avaya P330 Stack Master agent

OPR – Shows CPU boot status

PWR – Shows power ON/OFF or BUPS in

use

Connect the cables

Connect PCs, servers, routers, workstations, and hubs

1. Connect the Ethernet connection cable (not supplied) to a 10/100 Mbps port on the front

panel of the Avaya P333T-PWR.

LYou should use standard RJ-45 connections. You must use CAT-5 cable for 100 Mbps

operation.

2. Connect the other end of the cable to the Ethernet port of the PC, server, router, worksta-

tion, switch or hub.

LUse a cross cable when connecting the Avaya P333T-PWR to a switch or hub.

3. Check that the appropriate link (LNK) LEDs light up.

Connect the console cable

1. Configure the serial port settings of the PC or terminal as follows: Baud Rate – 9600, Parity

– no, Data bits – 8, Stop bits – 1, Flow control – no.

2. Connect the supplied special RJ-45 connector to the port marked “Console” on the front

panel of the Avaya P333T-PWR.

3. Connect the other end of the cable to a terminal or PC with terminal emulation software

installed.

Avaya P333T-PWR LEDs Port LEDs

Left/Right &

Reset Switches Function LEDsFIV switch

Basic configuration

To connect a PC terminal or VT-100 terminal to the Avaya P330

1. If you are using a PC, initiate a VT-100 terminal emulation session using an application

such as Windows® HyperTerminal.

2. Press Enter.

XThe Welcome to Cajun P330 menu is displayed.

3. Type the User name root when prompted and press Enter.

4. Type the default password root when prompted and press Enter.

XThe Cajun_P330-N(super)# prompt appears

LNis the number of the switch in the stack.

Assigning the Stack IP Address

LCommands are shown as follows: set interface inband;

parameters which you need to enter are shown in

as follows:

<vlan>

1. Type set interface inband

replacing

and

with the VLAN, IP address and net mask of

the stack and press Enter.

2. Type reset and press Enter to reset the stack.

3. After the Reset, perform login again as described above.

XThe Cajun_P330-N(super)# prompt appears.

4. Type set ip route

, replacing

and

with the destination and gateway IP addresses.

5. Press Enter to save the destination and gateway IP addresses.

Setting the Parameters

If you wish to change the default parameters shown and configure the mandatory

parameters, we recommend that you use the Command Line Interface (CLI).

LFor further information, please refer to the Avaya P333T-PWR User’s Guide.

Default Switch Settings

Default Port Settings

Parameter Default Setting

10/100Base-TX Ports 100Base-F Ports 1000Base-X Ports

Duplex mode Full duplex Full duplex Full duplex only

Port speed (Mbps) 100 10 1000

Flow control Off Off Off

Backpressure On (only in Half duplex) Not Applicable

Auto-negotiation Enabled Not Applicable Enabled

Administration status Enabled

Port VLAN ID 1

Tagging Mode Clear

Port Priority Regular

Inline Power Enabled Not Applicable

Inline Power Priority Low Not Applicable

Parameter Default Setting

Avaya P330 IP Address 149.49.32.134

BootP Mode Never

Default Gateway 0.0.0.0

Management PC SLIP IP Address 192.168.10.2

VLAN Management ID 1

Spanning Tree Enabled

TFTP Mode Limited

TFTP Server 0.0.0.0

TFTP File Name viisa

Run the Web-Based Manager (optional)

LTo configure the Avaya P333T-PWR you can use the P330 Web-based Manager in addi-

tion to using the CLI.

System Requirements

Minimum hardware and Operating System requirements are:

• Pentium® II 400 Mhz-based computer with 128 Mb of RAM

• Screen resolution of 1024 x 768 pixels

• Microsoft® Internet Explorer® 5 or Netscape Navigator® 4.x

• Windows® 95, NT® 4.0 (server/workstation) or Windows 2000 (server/workstation)

• Sun Microsystems Java™ plug-in (supplied on the “Documentation and Utilities” CD)

LRefer to the Release Notes for the exact version of the Java plug-in

Running the Embedded Manager

LAssign an IP address to the P333T-PWR before starting this procedure.

1. Open your browser.

2. Enter the URL of the switch in the form http://aaa.bbb.ccc.ddd

Laaa.bbb.ccc.ddd is the IP address of the switch.

XYou are prompted to log into the switch.

LThe user name is “root”.

The default password for read-write access is “root”.

LThe Web management passwords are the same as those of the CLI. If you have created

additional CLI user names or changed the default passwords then you can use those

passwords for Web management as well.

XThe welcome page is displayed:

LIf the network manager has configured the system the plug-in should be installed auto-

matically.

If the plug-in is not installed automatically, there are three ways to install the plug-in

manually:

• Either install the plug-in from the CD as follows:

1. Close all unnecessary applications on your PC.

2. Insert the “Avaya P330 Documentation and Utilities” CD in the CD drive.

3. Open Windows® Explorer.

4. Open the embweb-aux-files\ folder on the CD

5. Double click on the plugin_a_b_c.exe file (a, b and c are the version numbers of the

plug-in).

6. Follow the on-screen instructions.

• Or install the plug-in from the Avaya site by clicking on the link on the welcome page.

• Or, if the network manager has placed the files on the local site, install the plug-in from

there by clicking the link on the welcome page.

XIf you have the Java plug-in already installed or once you have successfully installed the

plug-in as described above, the Web-based manager opens in your browser.

Documentation and Online Help

Refer to the Avaya P330 Documentation and Utilities CD for full instructions.

Andere Handbücher für P333T-PWR

Inhaltsverzeichnis

Andere Avaya Schalten Handbücher

Avaya

Avaya 5900 Series Bedienungsanleitung

Avaya

Avaya P332G-ML Bedienerhandbuch

Avaya

Avaya ERS 3500 Series Bedienungsanleitung

Avaya

Avaya P133G2 Bedienungsanleitung

Avaya

Avaya Cajun P550R Bedienungsanleitung

Avaya

Avaya M15-155 Bedienungsanleitung

Avaya

Avaya P460 Produkthandbuch

Avaya

Avaya P460 Bedienungsanleitung

Avaya

Avaya MX10 Bedienungsanleitung

Avaya

Avaya P130 SMON Bedienungsanleitung

Avaya

Avaya P332G-ML Bedienungsanleitung

Avaya

Avaya ERS 8600 Bedienungsanleitung

Avaya

Avaya C360 Manager Bedienungsanleitung

Avaya

Avaya 4900 Series Bedienungsanleitung

Avaya

Avaya 2500 Series Bedienungsanleitung

Avaya

Avaya Cajun P333T Bedienungsanleitung

Avaya

Avaya 5900 Series Bedienungsanleitung

Avaya

Avaya P334T-ML Bedienerhandbuch

Avaya

Avaya 4000 Series Leitfaden

Avaya

Avaya 8800 Series Betriebsanleitung

Avaya

Avaya 8800 Series Bedienungsanleitung

Avaya

Avaya C360 Manager Bedienerhandbuch

Avaya

Avaya P120 SMON Bedienungsanleitung

Avaya

Avaya M770 Handbuch

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung