Avery Dennison ZM 110 Bedienungsanleitung

AWT35-501813 Issue AA Page 1

User Manual

Model: ZM 110

Bench Scale

AWT35-501813 Issue AA Page 2

Avery Weigh-Tronix is a trademark of the Illinois Tool Works group of companies whose ultimate parent company is

No part of this publication may be reproduced, stored in an electronic retrieval system, or transmitted in any form or by any

means, electronic, mechanical, photocopying, recording or otherwise without the prior written consent of the copyright owner, or

as permitted by law or under license. Full acknowledgment of the source must be given.

Avery Weigh-Tronix is a registered trade mark of the Avery Weigh-Tronix group of companies. This publication was correct at the

time of going to print however, Avery Weigh-Tronix reserves the right to alter without notice the specification, design, price or

conditions of supply of any product or service at any time.

All third party brands and product names used within this document are trademarks or registered trademarks of their respective

holders.

Aucune partie de cette publication ne peut être reproduite, enregistrée dans un système de récupération électronique ou

transmise sous quelque forme ou par quelque moyen que ce soit, électronique ou mécanique, par photocopie, enregistrement

ou autre, sans l’accord écrit préalable du propriétaire du droit d’auteur ou tel qu’autorisé par la loi ou dans le cadre d’une licence.

La source doit être reconnue dans son intégralité. Avery Weigh-Tronix est une marque déposée du groupe de sociétés Avery

Weigh-Tronix. Le contenu de cette publication était correct au moment de sa mise sous presse. Toutefois, Avery Weigh-Tronix

se réserve le droit de modifier à tout moment et sans préavis les spécifications, la conception, les tarifs ou les conditions

d’approvisionnement de tout produit ou service.

Toutes les marques et tous les noms de produits tiers utilisés dans ce document sont des marques de commerce ou des

marques déposées de leurs propriétaires respectifs.

ZM110_u_en_501860.docx

AWT35-501813 Issue AA Page 3

Table of Contents

1. General information and Warnings

page 6

FCC Declaration of Compliance - Déclaration de conformité..……...…………..…

Training - Formation……………………..………………………………...……………

Battery Safe Disposal - Élimination sécurisée desbatteries……...…………………

Routine Maintenance - Entretien de routine……………………………………..…

Cleaning the Machine - Nettoyage de la machine………………………….………

Sharp Objects - Objets tranchants………………………….………………...……....

2. Introduction

page 8

Unpacking…………………………………….………………………..…………………..

General Installation Guidelines……………………….…...…………………………….

Battery Operation…………………………….………………………..………………….

Powering ON/OFF the Scale………………………………………………………….…

Front Panel………...…………………………………….……………………………......

Error Codes………..…………………………………….……………………………......

3. Scale Operation

page 12

Gross Weighing……………………………………………………………………………

Tare Weighing.………………..……………………………………….………….……….

Clear a Tare………………….……………………….………………………………..

Counting Mode……………………………………………………………………………..

Sampling Parts Prior to Counting.………………….………………………………..

Checkweighing Mode....……..………………………………….…….………….……….

Setting the Checkweighing Limits………………….………………………………..

Checkweighing Beeper Modes…………………………..…………………………..

Hold Mode for Animal Weighing………………………………………......……..………

4. Menus

page 15

AWT35-501813 Issue AA Page 4

User Menu……………………..……………………………...……….………….……..….

User Menu Levels………………….………………...……….……………………..…

User Functions Descriptions [UF].………………….……….…………………..……

Supervisor Menu....………………………….……………..………………….……..…….

Supervisor Menu Levels……..……….………………………………………..……...

Supervisor Functions Descriptions [LF].…………..….……………………..….…...

Quick Calibration Menu……..………………………..……………………….……..…….

Quick Calibration Menu Levels…...…………….……………………...……..………

Quick Calibration Functions Descriptions [ECF]…..…………………………..……

5. Scale Configuration [LF 2]

page 19

6. Calibration

page 20

Enabling the Calibration Procedure..….………………………………………………..

Scale Calibration Procedure...………….………………………………………………..

Stamped Calibration……….....………….………………………………………………..

7. Replacement Parts

page 22

9. Loadcell Pinouts

page 22

AWT35-501813 Issue AA Page 5

Manual revision history

Current Issue

Date Created

Details of Changes

Draft

Jan. 2019

New

Please be aware this product contains

a lead acid battery which MUST be

removed and disposed of safely prior

to any disposal of the scale.

AWT35-501813 Issue AA Page 6

1. General Information and Warnings

1.1. FCC Declarations of Compliance - FCC Déclaration de conformité

United States

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

Canada

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la Classe A prescrites dans le Règlement sur le brouillage

radioélectrique edicté par le ministère des Communications du Canada.Interference Regulations of

the Canadian Department of Communications.

AWT35-501813 Issue AA Page 7

1.2. Training - Formation

Do not attempt to operate or complete any procedure on a machine unless you have received the

appropriate training or read the instruction books.

Ne pas tenter d’utiliser la machine ou lui appliquer une quelconque procédure sans avoir reçu une

formation adaptée ou lu les manuels d’instruction.

CAUTION! Risk of electrical shock. Refer to qualified service personnel for service.

ATTENTION! Risque de choc électrique. Confier la réparation de l’appareil à un

personnel qualifié.

1.3. Safe Battery Disposal - Élimination sécurisée des batteries

Please be aware this product contains a lead acid battery which MUST be removed and disposed of

safely prior to any disposal of the scale.

This battery can be easily accessed by removing the battery cover found on the underside of the

indicator.

CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type recommended by the manufacturer.

ATTENTION! Il y a danger d'explosion s'il y a remplacement incorrect de la batterie,

remplacer uniquement avec une batterie du même type ou d'un type équivalent

recommandé par le constructeur.

1.4. Routine Maintenance - Entretien de routine

IMPORTANT: This equipment must be routinely checked for proper operation and calibration.

Application and usage will determine the frequency of calibration required for safe operation.

PRUDENCE: Le fonctionnement et l’étalonnage de cet équipement doivent être vérifiés régulièrement.

Les applications et l’utilisation déterminent la fréquence de l’étalonnage requis pour une utilisation en

toute sécurité.

1.5. Cleaning of Scale - Nettoyage de la machine

Do - Ce qu’il faut faire

Do NOT - Ce qu’il ne faut pas faire

Wipe down the outside of product with a clean

cloth, moistened with water and a small amount of

mild detergent cleaning fluid.

Essuyer la partie externe des produits standard à

l’aide d’un chiffon propre légèrement imprégné

d’eau et d’une petite quantité de détergent doux.

Use harsh abrasives, solvents, scouring

cleaners or alkaline cleaning solutions.

Utiliser des produits abrasifs, des solvants, des

produits de récurage ou des solutions de

nettoyage alcalines.

Spray on to the cloth when cleaning and not

directly onto the indicator area.

Pulvériser tout produit de nettoyage spécifique sur

le chiffon.

Do not attempt to clean the inside of the

machine.

Tenter de nettoyer l’intérieur de la machine.

Spray any liquid directly on to the display

windows.

Pulvériser des liquides directement sur les

écrans d’affichage.

1.6. Sharp Objects - Objets tranchants

Do not use any sharp objects such as screwdrivers or long fingernails to operate the keys.

Ne pas appuyer sur les touches avec des objets tranchants tels que des tournevis ou même des ongles

longs.

AWT35-501813 Issue AA Page 8

2. Introduction

The ZM110 is a general purpose indicator ideal for connecting to most bench and floor scales.

This indicator can easily be desk or pole mounted and comes with an AC power adaptor along with a

rechargeable lead acid battery to allow the scale to be used in applications where power outlets are

limited.

This ZM110 indicator comes standard with a range of easy to operate General weighing functions along

with basic Checkweighing and Counting.

2.1 Unpacking

Carefully take the scale out of its package, make it sure it’s not damaged and all accessories are

included.

•Remove the scale from the carton;

•Remove the protective covering;

•Inspect the scale and indicator/display for damage;

•Make sure all components are included:

1. ZM110 Indicator

2. Adaptor plus plug adaptors

3. Platform, column and brackets

4. Product manual

2.2. General Installation Guidelines

To get the best performance from the scale, place the ZM110 in a location that will not degrade its

accuracy.

•Avoid extremes of temperature. Try to avoid placing the scale in direct sunlight or near air vents;

•Place the scale on a level flat surface. Do not place the scale near vibrating machinery;

•Avoid unstable power sources. Do not use near welding equipment or other large users of electricity.

2.2.1 Levelling the Scale

Level the scale using the four adjustable feet on the bottom of the scale, Figure 1, and the bubble level

near the base of the column, Figure 2.

Always check the level prior to using scale.

Fig. 1 Adjust scale feet to level the scale

Fig. 2 Adjust feet until bubble is

centered in the black circle

AWT35-501813 Issue AA Page 9

2.2.2 Scale Installation

1. Attach the support column to the bracket at the back of the scale base using the three mounting

screws. Use a 3mm hex (Allen) key to tighten the screws. See Figure 3.

Fig. 3 Insert column into bracket and secure with three screws

2. Place the indicator on the top bracket as shown in Figure 4 and slide it down until it snaps into

the final position. Loosen the adjustment knob shown in Figure 4 and adjust the indicator’s

angle for best viewing of the display, then tighten the knob.

Fig. 4 Slide indicator head onto column bracket

3. The cable from the base to the indicator is run through the column and out through the plastic

bracket at the top when you unpack the scale. Make sure the connector is free of obstructions,

i.e. packing foam, and plug the cable into the connector, as shown in Figure 5. Tighten the

threaded collar.

4. Attach the AC power adapter to the connector on the back of the indicator. See Figure 5.

Fig. 5 Signal cable plugged into back of the indicator

AWT35-501813 Issue AA Page 10

2.3. Battery Operation

The ZM110 can be operated from a 6V 4Ahrs battery located inside the indicator or plugged into an

acceptable power outlet. Battery life is approximately 107 hours with the backlight off.

When the battery needs charging this symbol, , appears in the upper left corner of the weight

display. The scale will still operate for about 10 hours after which it will automatically switch off to protect

the battery.

When the scale is turned on, the battery status is shown by:

-Green LED, battery is fully charged;

-Red LED, battery is low and needs to be recharged.

Do not use any other type of power adaptor other than the one supplied with the scale and verify that

the AC power socket outlet is properly protected.

Charge the battery for at least 12 hours before using.

2.4. Powering On/Off the Scale

With the platform connected and the battery fully charged or the charger plugged into the indicator,

press the ON key to power ON the scale. A display test will be performed on power up and the scale

will finish in normal weighing mode. Press the OFF key to turn the scale off.

2.5. Front Panel

The indicator has a sealed keypad and a 6 digit LCD display, 0.59” (40mm) high with white backlight.

Only active annunciators are shown below.

2.5.1. Display Annunciators

Display reading is stable

Scale at Zero

NET

Indicates a Net weight

GROSS

Indicates a Gross weight

Under acceptable weight range

Within acceptable weight range

Over acceptable weight range

Battery needs to be recharged

kg lb g

Current unit of measure

Inhaltsverzeichnis

Andere Avery Dennison Skala Handbücher

Avery Dennison

Avery Dennison A-102 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung