AVS J3 Series Kurzanleitung

Step by Step Wiring Diagram

J3 & J3C Modulang Electric Valve Actuators

WIRING & OPERATING THE ACTUATOR FOR MODULATING

AND FAILSAFE MODULATING FUNCTION

J3 J3C Modulating Wiring Step by Step Rev 0 AVS

J3 & J3C SERIES: ACTUATOR COVER & DIN PLUG IDENTIFICATION

DIN PLUG IDENTIFICATION

Models: J3-H, J3-L, J3C-H, J3C-L, J3CS

DIN Plug No Colour Connecon

Grey plug & base External power

Black plug & base Control signal (I/O)

Black plug & base End of travel conrmaon

❶❷❸

❶

❸

❷

J3/ J3C / J3CS MODULATING ELECTRIC ACTUATOR

Movement of the actuator is proporonal to input signal

Power is applied connuously. Movement of valve actuator is then controlled by an internally ed digital posion-

er and is proporonal to changes supplied in an input control signal. This input signal is typically 0-10VDC, or 4-

20mA. An output signal is supplied as standard providing closed loop control. Fails closed on loss of control signal

(or see conguraon opons below), but stays put on loss of external power.

Conguraon opons:

1) Closes on loss of control signal

2) Opens on loss of control signal

3) Stays put on loss of control signal (Fail freeze)

J3/ J3C / J3CS FAILSAFE MODULATING ELECTRIC ACTUATOR (same wiring as modulang version)

Combinaon of failsafe & modulang above:

Uses baery failsafe system and digital posioner to provide fail to safe posion funcon on loss of external power.

❶❸❷

J3 & J3C SERIES: MODULATING & FAILSAFE MODULATING FUNCTION

Models: 20, 35, 55, 85

Models: 140, 300

Step by Step Wiring Diagram

J3 & J3C Modulang Electric Valve Actuators

Make the live (L) or posive (+) connecons:

In a modulang valve actuator, the power is

permanently applied and NOT switched as in

an on-o or failsafe actuator.

Connect a live to pin 2 of the external power

Din plug, and to pin 1 of the posion conr-

maon plug.

Apply power to pin 1 of the posion conr-

maon plug for end of travel conrmaon.

This circuit is made around 5° ahead of the

nal closed posion.

Make the neutral (N) connecons:

1 x External power Din plug, pin 1

1 x Open conrmaon Din plug, pin 3

1 x Closed conrmaon Din plug, pin 2

Connecng:

②

③

①

N/- L/+

VAC/VDC

External Power

L/+ N/-

N/-

OPEN

Posion Conrmaon

VAC/VDC

③

②

③

①

N/- L/+

VAC/VDC

External Power

*Customer supplied

①

L/+ N/-

N/-

CLOSE OPEN

Posion Conrmaon

VAC/VDC

③

②

*Customer supplied

①

❶

❷

4-20mA or 0-10V

Grey Plug

& base

Input

Customer supplied

WIRING DIAGRAM

*Customer supplied

L/+ N/-

N/-

CLOSED OPEN

Volt free

Posion Conrmaon

VAC/VDC

②

③

①

N/- L/+

VAC/VDC

External Power

③

①②

①

Output

4-20mA /

0-10VDC

③

②

Control Signal I/O

Customer supplied

Supplied with actuator

Right Black

Plug & base

Grey Plug

& base

Do not connect

Centre Black

Plug & Base

Centre Black

Plug & Base

ELECTRICAL CONNECTIONS

(We recommend only qualied electrical engineers make the connecons)

Control Signal Connecons (Centre DIN Plug)

Note: This Din plug is inverted to help prevent the possibility of the posion conrma-

on plug being connected to the control connecon, as doing so will irreparably dam-

age the DPS posioner. Such damage is not covered by the warranty.

①

+4-20mA /

0-10VDC

Input

Output

4-20mA /

0-10VDC

③

②

Control Signal I/O

Customer supplied

Step by Step Wiring Diagram

J3 & J3C Modulang Electric Valve Actuators

①

+4-20mA /

0-10VDC

Input

Output

4-20mA /

0-10VDC

③

②

Control Signal I/O

Customer supplied

①

+4-20mA /

0-10VDC

Input

Output

4-20mA /

0-10VDC

③

②

Control Signal I/O

Customer supplied

Do not connect

❸

Make the negave connecon from the negave output from your 4-

20mA (or 0-10VDC) device to pin 1 . Correct polarity of these control signal

connecons is crical so please double check.

❹

Make the posive connecon from the posive output from your 4-20mA

(or 0-10VDC) device to pin 2. Correct polarity of these control signal

connecons is crical so please double check.

If you are using the feedback signal from the J+J actuator posioner, make

the output connecon to the posive input to your 4-20mA (or 0-10VDC)

device to pin 3 .

The pin marked as earth (ground) on the control Din plug MUST NOT

BE CONNECTED to anything. This pin is used for an external reset

funcon and the posioner will not funcon correctly if any external

connecons are made to this pin.

The pin marked as earth (ground) on the control Din plug MUST NOT

BE CONNECTED to anything. This pin is used for an external reset

funcon and the posioner will not funcon correctly if any external

connecons are made to this pin.

The pin marked as earth (ground) on the control Din plug MUST NOT

BE CONNECTED to anything. This pin is used for an external reset

funcon and the posioner will not funcon correctly if any external

connecons are made to this pin.

❺

-ve

+ve

Centre Black

Plug & Base

Centre Black

Plug & Base

Centre Black

Plug & Base

Dieses Handbuch passt für folgende Modelle

Andere AVS Controller Handbücher

AVS

AVS Rotators Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung