Axiohm A721 Bedienungsanleitung

A721 Multifunction Printer:

Setup Guide

7221-D110

A721 Multifunction Printer:

Setup Guide

7221-D110

Axiohm IPB

Ithaca, New York

ii August 1998

Disclaimer

Information in this document is subject to change without notice. Therefore,

before using this document, consult your Axiohm sales representative for

information that is applicable and current. Axiohm reserves the right to improve

products as new technology, components, software, and firmware become

available.

No part of this document may be reproduced or transmitted in any form or by

any means, electronic or mechanical, for any purpose without the express written

permission of Axiohm.

Ithaca, New York USA

Printed in USA

Confidential, Unpublished

Property of AXIOHM

Trademarks

AXIOHM is the registered trademark of AXIOHM. Other trademarks and

registered trademarks are the property of their respective holders.

A721 Setup Guide Contents

August 1998 iii

Important Information to the User

In order to ensure compliance with the Product Safety, FCC and CE marking

requirements, you must use the power supply, power cord, and interface cable

which were shipped with this product or which meet the following parameters:

Power Supply

UL Listed (QQGQ), Class 2 power supply with SELV (Secondary Extra Low

Voltage), non-energy hazard output, limited energy source, input rated 100-240

Vac, 1.5/0.8 A, 50/60 Hz, output rated 24 Vdc, 2.3 A.

Use of this product with a power supply other than the Axiohm power supply

will require you to test this power supply and Axiohm printer for FCC and CE

mark certification.

Interface Cable

A shielded (360 degree) interface cable must be used with this product. The

shield must be connected to the frame or earth ground connection or earth

ground reference at EACH end of the cable.

Use of a cable other than described here will require that you test this cable with

the Axiohm printer and your system for FCC and CE mark certification.

Power Cord

A UL listed, detachable power cord must be used for this product. For

applications where the power supply module may be mounted on the floor, a

power cord with Type SJT marking must be used. For applications outside the

US, power cords which meet the particular country’s certification and

application requirements should be used.

Use of a power cord other than described here may result in a violation of safety

certifications which are in force in the country of use.

Industry Canada (IC)

Radio Frequency Interference Statement

This Class A digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du

Règlement sur le matériel brouilleur du Canada.

iv August 1998

Federal Communications Commission (FCC)

Radio Frequency Interference Statement

Warning

Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

Note

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Communication Cables

Shielded communication cables must be used with this unit to ensure compliance

with the Class A FCC limits.

Information to User

This equipment must be installed and used in strict accordance with the

manufacturer's instructions. However, there is no guarantee that interference to

radio communications will not occur in a particular commercial installation. If

this equipment does cause interference, which can be determined by turning the

equipment off and on, the user is encouraged to contact Axiohm immediately.

The Axiohm company is not responsible for any radio or television interference

caused by unauthorized modification of this equipment or the substitution or

attachment of connecting cables and equipment other than those specified by

Axiohm. The correction of interferences caused by such unauthorized

modification, substitution or attachment will be the responsibility of the user.

A721 Setup Guide Contents

August 1998 v

Contents

Contents v

Chapter 1: Unpacking the Printer 1

What Is in the Box? 1

Removing the Packing Material 1

Repacking the Printer 2

Chapter 2: Setting Up the Printer 3

Setting Switches 4

Setting RS-232C Communication Parameters 5

Setting Parallel Communication Parameters 6

Switch Entry Mode 7

Connecting the Cables 19

Loading Paper 20

Loading Receipt Paper 20

Loading Receipt/Journal Paper 22

Installing the Ribbon Cassette 24

Testing the Printer 25

Running the Print Test 25

Sample of Test Printout 26

Adjusting the Printhead Gap 27

Contents A721 Setup Guide

vi August 1988

A721 Setup Guide Chapter 1: Unpacking the Printer

August 1998 1

Chapter 1: Unpacking the Printer

Follow these instructions to unpack the printer. Save all the packing materials for

re-packing the printer if needed.

What Is in the Box?

The following items are packed in the shipping box:

•Printer enclosed in a plastic bag and foam pack

•Test printout (inside receipt bucket)

•Foam restraint for the slip table

•Foam restraint for the carriage (under front cover)

•Power supply with cable connecting to printer with strain relief and

power supply cord connecting to power outlet (in box—only if ordered

with the printer)

•Receipt paper roll (if ordered) and ribbon cassette (in box)

Caution: Do not remove the mylar shield on the ribbon cassette or the

ribbon cassette will be ruined. The shield protects against smudging.

•Installation report card

Removing the Packing Material

1. When the printer is removed from the packing materials, open the rear

cover by pulling up on the front left corner.

2. Remove the test printout and installation report card from inside the

receipt bucket.

3. Remove the foam restraint for the slip table between the slip table and

cabinet.

4. Open the cassette cover and remove the foam restraint from the

carriage.

Chapter 1: Unpacking the Printer A721 Setup Guide

August 1998

5. Remove the ribbon cassette, receipt roll, power supply, and cables from

the box.

6. Save all packing materials for future storing, moving, or shipping.

Caution: Be sure that both of the foam restraints have been removed before

operating the printer.

Cassette

Cover

Foam

Restraint

Foam

Carriage

Restraint

Rear

Cover 1

Lower

Cantilever

Cover

Slip

Table 3

4Carriage

Lower Cantilever

Cover

(Cassette Cover

removed for clarity)

Repacking the Printer

1. Open the cassette cover and remove the ribbon cassette.

2. Move the carriage to the right and place the foam restraint for the

carriage between the left side of the printer and the carriage.

3. Place the foam restraint for the slip table between the slip table and the

cabinet.

4. Place the printer in the plastic bag and foam pack.

5. Place the packed printer in the box and secure with packing tape.

6. Contact your Axiohm authorized service organization for information

on where to send the printer.

Be prepared to answer questions concerning shipping and billing.

A721 Setup Guide Chapter 2: Setting Up the Printer

August 1998 3

Chapter 2: Setting Up the Printer

The A721 printer may be placed on a level surface on or near the host computer.

Make sure there is enough room to open the cover to change the paper and

ribbon cassette. The illustration shows the actual dimensions of the printer, but

leave several inches around the printer for connecting and accessing the cables.

This printer was designed to operate in the environment outlined in the

“Environmental Requirements” section of Appendix A in the A721

Multifunction Printer Owner’s Guide. Operation outside these ranges as defined

may lead to degradation of the printer functionality and reliability, and may

result in higher than specified service call rates. In environments which contain a

high level of contaminants, dirt, airborne debris or particles, preventative

maintenance will be required.

Note: The MICR check reader feature has been factory adjusted for a normal

operating environment with a host computer. However, additional devices, such

as CRT monitors or large metal surfaces near the printer, can affect the printer's

magnetic field, causing intermittent reading errors when the MICR check reader

is in operation.

This condition can be easily diagnosed by checking the noise level of the MICR

check reader. See chapter 2 in the A721 Multifunction Printer Owner’s Guide

for more information.

165 mm

(6.5 in.) 259 mm

(10.2 in.)

165 mm

(6.5 in.)

w/Journal 147.3 mm

(5.8 in.)

Receipt Only

Andere Handbücher für A721

Inhaltsverzeichnis

Andere Axiohm Drucker Handbücher

Axiohm

Axiohm A758 Bedienungsanleitung

Axiohm

Axiohm THTN Series Bedienungsanleitung

Axiohm

Axiohm 24V Bedienungsanleitung

Axiohm

Axiohm CMBC-XMBC Bedienungsanleitung

Axiohm

Axiohm APOS PRINTER SERIES Bedienungsanleitung

Axiohm

Axiohm SKGG5xxx Series Bedienungsanleitung

Axiohm

Axiohm A794-D100 Bedienungsanleitung

Axiohm

Axiohm A220 Bedienungsanleitung

Axiohm

Axiohm A795 Bedienungsanleitung

Axiohm

Axiohm A630 Bedienungsanleitung

Axiohm

Axiohm TPOS PRINTER SERIES Bedienungsanleitung

Axiohm

Axiohm A794 Bedienungsanleitung

Axiohm

Axiohm Astrium Bedienungsanleitung

Axiohm

Axiohm A758 Bedienungsanleitung

Axiohm

Axiohm A794 Bedienungsanleitung

Axiohm

Axiohm 7193 Bedienungsanleitung

Axiohm

Axiohm A795 Bedienungsanleitung

Axiohm

Axiohm A794 Bedienungsanleitung

Axiohm

Axiohm 7156 Bedienungsanleitung

Axiohm

Axiohm PCPR Printer Bedienungsanleitung

Axiohm

Axiohm APM-90 Bedienungsanleitung

Axiohm

Axiohm A714 Bedienungsanleitung

Axiohm

Axiohm TELESTO Bedienungsanleitung

Axiohm

Axiohm TPOSS001 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung