Axis FC-29W Kurzanleitung
FC-29W
9”
UN-UNIVERSAL
Dome Housing
Installation Instructions
1
Safe Use of Equipment
WARNING
WARNING
To reduce the risks of an electric shock, do not expose inside of this
unit to rain or moisture.
Installation on a rainy day may also cause fog around the capsule.
Installation
Installation shall be done by qualified installer only and should
conform to all local codes.
Ensuring strength of supporting Dome Housing Unit
The unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit. Recommend
use 3/8” stainless screws x four (4).
Prohibit changes or modifications of equipment
You are cautioned that any changes or modifications not expressly
approved in these instructions could void your authority to operate
this equipment.
Basic Operating Environment Condition
We provide warranty for the products that are installed under normal
outdoor -20°C ~ +50°C conditions. We are unable to provide warranty
for the products which are installed indoor and exposed to constant
high temperature over +50°C and over 90% humidity.
Operating temperature and humidity of camera varies from camera to
camera. You are requested to confirm to camera specification with
camera manufacturer and housing specification with us in advance.
i.e. -20°C or below, you are requested to use additional heater and
+50°C or above you are requested to use two blowers and Sunshield.
Fasten wires tightly.
Attention:
Keep wires away from the Fan / Heater, and do not disturb
Fan/Heater’s performance
2
Table of contents
1. AXIS 214 PTZ network camera housing installation………………………..P.4
2. AXIS 215 PTZ network camera housing installation……………………..…P.6
3. AXIS 233D PTZ network dome camera Housing installation……………...P.8
4. AXIS P55XX series PTZ network dome camera Housing installation…....P.10
5. AXIS Q6034 PTZ network dome camera Housing installation………...….P.12
6. Installation of FC-9002 Pole Mount Bracket and Dome housing………….P.14
7. Installation of FC-9005 Ceil Mount Bracket and Dome housing …..….…..P.15
8. Installation of FC-9006 Ceil Mount Bracket and Dome housing …….....…P.16
9. Installation of FC-9007 Corner Adapter with Wall Mount Bracket and Dome
housing……………………………………………………………………….….P.17
10. Installation of FC-9008 Corner Adapter with Wall Mount Bracket and Dome
housing ………………………………………………………………….………P.18
11. Installation of FC-9009N Wall Mount Bracket and Dome housing …….....P.19
12. Installation of FC-9009 Wall Mount Bracket and Dome housing……….…P.20
13.Installation of FC-9011 Ceil Mount Bracket and Dome housing……….…..P.21
14.Dimensions …………………………….………….....................……………..P.22
3
1AXIS 214 PTZ network camera Housing installation
WARNING The unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of unit. Recommend use
stainless screws.
Cables
L603
Power cable to PC board and external power supply
L704
Power cable to PC board and PTZ network camera
9” dome housing
DC12V Fan+Heater
L705
Network extension cable to internet
Component Parts for Assembly
Square-shaped upper board No. 2 side board Round-shaped bottom board
Screw the camera on, through hole B,
with washer in the back No. 3 Allen Key ( for cover and wall
mount bracket tighten)
3x12 Double Washer screws for
camera to Square-shaped upper
board,
4
Assembly Steps of the Camera and the Dome Housing
1-1-1 1-1-2 1-1-3
Fix No. 2 side board (Hole 2) to the
round-shaped bottom board (Hole 5)
with 3x8 Double Washer screws.
Use 4x8 double washer screws to
Fix Fan/Heater side board on
Round-shaped bottom board,
connect power cable to Fan/Heater
Fix screws on back of
square-shaped upper board which
go through from back to front to fix
the camera on the square-shaped
upper board (Hole B) with 3x12
double washer screws.
Assembly Steps of the Cables
1-2-1 1-2-2 1-2-3
Use 4x8 double washer to Fix
Fan/Heater side board on
Round-shaped bottom board,
connect power cable to Fan/Heater
Connect L603 to the PC board.
Connect L704 to the PC board. Connect L704 and L705 to the
camera. Cables used for camera.
1
3
4
5
2
1. DC 12V FAN
2. DC 12V HEATER
3. H/SENSER
4. DC 12V OUT
5. DC 12V IN
L705 L704
L704 L603
5
2AXIS 215 PTZ network camera Housing installation
WARNING The unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of unit. Recommend use
stainless screws.
Cables
L603
Power cable to PC board and external power supply
L704
Power cable to PC board and PTZ network camera
9” dome housing
DC12V Fan+Heater
L705
Network extension cable to internet
Component Parts for Assembly
Square-shaped upper board No. 3 side board Round-shaped bottom board
Screw the camera on, through hole G,
with washer in the back No. 3 Allen Key ( for cover and wall
mount bracket tighten)
4x10 Double Washer screws for
camera to Square-shaped upper
board,
6
Assembly Steps of the Camera and the Dome Housing
2-1-1 2-1-2 2-1-3
Fix No. 3 side board (Hole 1) to the
round-shaped bottom board (Hole 6)
with 3x8 Double Washer screws.
Use 4x8 double washer screws to
Fix Fan/Heater side board on
Round-shaped bottom board,
connect power cable to Fan/Heater
Fix screws on front of square-shaped
upper board to fix the camera on
square-shaped upper board (Hole G)
with 4x10 double washer screws.
Assembly Steps of the Cables
2-2-1 2-2-2 2-2-3
Use 4x8 double washer to Fix
Fan/Heater side board on
Round-shaped bottom board,
connect power cable to Fan/Heater
Connect L603 to the PC board.
Connect L704 to the PC board. Connect L704 and L705 to the
camera. Cables used for camera.
1
3
4
5
2
1. DC 12V FAN
2. DC 12V HEATER
3. H/SENSER
4. DC 12V OUT
5. DC 12V IN
L704 L705
L704 L603
7
3AXIS 233D PTZ network dome camera Housing installation
WARNING The unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of unit. Recommend use
stainless screws.
Cables
L605P-2
Power cable to PC board and external power supply
L704P-2.0
Power cable to PC board and camera
9” dome housing
AC24V Fan+Heater
L705
Network extension cable to internet
Component Parts for Assembly
Square-shaped upper board No. 1 side board ＆L board Round-shaped bottom board
Screw the camera on, through hole E,
with washer in the back No. 3 Allen Key ( for cover and wall
mount bracket tighten)
4x10 Double Washer screws for camera
to Square-shaped upper board,
8
Assembly Steps of the Camera and the Dome Housing
3-1-1 3-1-2 3-1-3
Fix No. 1 side board (Hole 1) to the
round-shaped bottom board (Hole 5)
with 3x8 Double Washer screws.
Fix screws on front of square-shaped
upper board to fix the L board on
square-shaped upper board (Hole E)
with 4x10 double washer screws.
Fix the camera to the L board with
4x10 double washer screws.
Assembly Steps of the Cables
3-2-1 3-2-2 3-2-3
Use 4x8 double washer to Fix
Fan/Heater side board on
Round-shaped bottom board,
connect power cable to Fan/Heater
Connect L605P-2 to the PC board.
Connect L704P-2.0 to the PC board. Connect L704P-2.0 and L705 to the
camera. Cables used for camera.
1
3
4
5
2
6
1. DC 12V FAN
2. AC 24V HEATER
3. H/SENSER
4. DC 12V OUT
5. AC 24V OUT
6. AC 24V IN
L705 L704P-2.0
L704P-2.0 L605P-2
9
Inhaltsverzeichnis
Andere Axis Kamerazubehör Handbücher
Axis
Axis VT Verso HPV42K1A000 Bedienungsanleitung
Axis
Axis 24889 Merkblatt
Axis
Axis 26427R1 Bedienungsanleitung
Axis
Axis T92G20 Bedienungsanleitung
Axis
Axis ACH13HB Bedienungsanleitung
Axis
Axis 01457-001 Bedienungsanleitung
Axis
Axis F8201 Bedienungsanleitung
Axis
Axis T96A05-V Bedienungsanleitung
Axis
Axis Videolarm 25734 Merkblatt
Axis
Axis T92E series Bedienungsanleitung
Axis
Axis T91B61 Bedienungsanleitung
Axis
Axis TI8903 Bedienungsanleitung
Axis
Axis 22870 Merkblatt
Axis
Axis 211M Bedienungsanleitung
Axis
Axis TP3203 Bedienungsanleitung
Axis
Axis Geocalla G3-3D Bedienungsanleitung
Axis
Axis FA54 Bedienungsanleitung
Axis
Axis T91A52 Bedienungsanleitung
Axis
Axis AXIS T95A00 Bedienungsanleitung
Axis
Axis F9114-B Bedienungsanleitung
