Ayra ERO 3108 Bedienungsanleitung

RGBW LED beam movinghead

User manual

Safety precautions

WARNING: This unit may cause serious injury to the eyes when used incorrectly. It is therefore

strongly advised to read this user manual carefully, to get familiance yourself with the functions of this

device.

WARNING: This unit must be operated by, or under the supervision of an adult. This device is not

suitable for children.

WARNING: Do not look directly into the beam from a short distance. This may cause serious injury to

the eyes. Ayra is not responsible for any injuries caused by incorrect use of this device.

Installation requirements:

- Always check the power supply to which you want to connect the device. If the voltage requirements

do not meet, do not connect the device as this may cause serious damage.

- This device must be installed by a professional technician, in a standing or hanging position. Only

use the included mounting bracket if you want to position the unit against a ceiling or truss system.

- When installed in a hanging position above your audience, this unit MUST be secured by using a

safety cable, capable of holding 10x the weight of this device.

- The unit is designed to be installed with a halfcoupler or G-clamp, by using the included mounting

bracket. Direct installation with proper bolts is also possible.

- Make sure there are no flammable objects in the direct environment of the device.

- Do not block the beam-exit and fan.

- Keep a minimum distance of 0.25 meter from any walls to provide sufficient cooling.

- Make sure the beam-exit and fan are not blocked by any objects in the near environment.

- Always use the included power supply. Contact your local dealer for a replacement unit if necessary.

Maintenance and protection

- Keep the unit away from dusty environments, as this may have negative effects on the fan-cooling

system and optics. Clean the optics and fan with a small, soft brush and vacuum cleaner when

needed. Clean the housing of the unit with a damp cloth. WARNING: Always disconnect the unit from

the power supply when cleaning the unit. Reconnect the unit only when any moist on the fixture has

evaporated completely.

- Do not switch the power on and off frequently, as this may cause serious damage to the unit.

- Avoid heavy shocks and collision during transport and use, as this may cause damage to the LED

light source, electronic circuit, optics and housing.

- Keep the device away from moisture, rain, water or any liquids as this may cause a short circuit

and/or electric shocks. If any liquid enters the unit, power supply or housing of the unit, disconnect the

unit immediately and do not reconnect the power supply. Contact your local dealer or technician to

inspect the unit for any damage.

Box contents

1x ERO 3108 movinghead

1x power cable

1x XLR-XLR signal cable

1x installing bracket

1x safety cable

Unit and accessory inspection

- Always use the supplied power cable to connect the unit to a power supply. If the cable appears

broken or has visible damage, do not use it.

- If the unit is not going to be used for a longer period of time, disconnect it from the power supply and

store it in a dust-free environment.

- Always check the unit for possible damage before use. If you suspect that something is wrong with

the unit, do not connect it to a power source! When you suspect that your unit is broken or damaged,

contact your local dealer or a certified technician to inspect the unit.

- When your device does not generate any light, do not look directly into the lens. When the fixture

suddenly produces a beam, it may cause injury to your eyes.

Device overview

1. Beam output

2. Control panel with display and menu-functions

3. On/off switch

4. Fuse

5. Power input (Twist-lock connector)

6. DMX input

7. DMX output

8. Transport handles

Setting up the unit

To activate the unit, connect the included power supply to the unit and a suitable 230V, 50 Hz power

outlet. Switch the on/off switch to the ‘ON’ position, the LED movinghead will activate.

Give the movinghead time to calibrate the stepping motors, which are used to determine the position

of the head. You may hear and see some shaking, which is normal. The stepping motors use an end

point to determine the beginning and end of their movement. After calibration, the movinghead will

start the previously used mode, but by default it is set to DMX mode.

The display shows several settings, each with the possibility to set several values. In the table below is

an explanation for every feature and value.

Menu item

Description

Values/options

‘Enter’ triggers

action

Followed by

DMX ADDRE

Press enter and

use up/down to

change the DMX

address

1 –512

Set DMX address

Press Menu to

return to the main

PAN INVERT

Press enter and

use up/down to

change the pan

inversion

Yes / no

When ‘yes’ is

selected, the

behavior of the

pan function will

be inverted

Press Menu to

return to the main

PAN ANGLE

Press enter and

use up/down to

change the pan

angle

540 / 630

Choose between

a pan angle of

maximum 540 or

630 degrees

Press Menu to

return to the main

TILT INVERT

Press enter and

use up/down to

change the tilt

inversion

Yes / no

When ‘yes’ is

selected, the

behavior of the tilt

function will be

inverted

Press Menu to

return to the main

MODE

Use the up/down

buttons and enter

to choose a

working mode

DMX 512

SLAVE

AUTO

SOUND

Scroll and press

enter to select an

operating mode

Press Menu to

return to the main

MANUAL

Press enter to

access the

manual operating

mode

CH:XX

Date(XXX)

Select a channel

(CH:XX) and a

value for the

channel

(Date(XXX)).

Press Enter to

save the setting.

RESTORE

Press enter to

access the Motor

and Factory reset

Motor reset =

recalibrate the

pan and tilt

motors

Factory reset =

Reset the fixture

to factory settings

Press enter to

activate the reset

function for the

motors or factory

reset.

The display will automatically shut down after 30 seconds of inactivity. When pressing one of the menu

buttons, the menu backlight will re-activate.

The ERO 3108 is equipped with several working modes, each with its own advantages. For simple

events there are stand-alone modes, for advanced situations there are options to create synchronized

lightshows, or controlled with a DMX-512 controller. A short description for each mode can be found

below:

Auto:

Automatic lightshow with a pre-programmed internal show, on a pre-defined speed.

Sound:

Automatic lightshow with a pre-programmed internal show, on the beat of the music, thanks to an

internal microphone which senses the beat of the music and will change a step every time a beat is

detected.

Slave:

In master/slave mode, it is possible to link several ERO 3108 movingheads together, to create

synchronized lightshows in the Auto or Sound mode. The first fixture in the chain needs to be set in

the Auto or Music mode. All the next fixtures need to be set to Slave and will mimic the behavior of the

first fixture. The master/slave function requires XLR –XLR cables (not included).

DMX:

The ERO 3108 movinghead can be connected to a DMX-controller with standard XLR –XLR cable.

While doing so, a DMX-terminator must be connected to the last fixture, at the end of the DMX-chain.

This prevents reflections in the DMX-signal, which could cause flickering and unwanted behavior from

your intelligent fixtures.

A DMX terminator is a XLR connector with a resistor of 120 Ohm, placed between pin 2 and 3 as a

bridge. See the illustrations below for more information.

With the following channel assignment, it is possible to control the ERO 3108 movinghead:

Channel

Function

Value

Description

Pan

0-255

Pan movement 8-bit

Tilt

0-255

Tilt movement 8-bit

Dimmer

0-255

Dimmer function 0-100%

Strobe

0-6

No function

7-65

Strobe function Slow –Fast

66-69

No function

70-128

Pulse strobe (Slow –Fast)

129-132

No function

133-191

Strobe fade in (Slow –Fast)

192-195

No function

296-255

Strobe fade out (Slow –Fast)

Red

0-255

Red 0-100% dimmer

Green

0-255

Green 0-100% dimmer

Blue

0-255

Blue 0-100% dimmer

White

0-255

White 0-100% dimmer

Motor speed

0-255

Fast –Slow movement speed

RGB macro function

0-4

No function

5-44

Eight fixed colors

45-49

No function

50-94

Eight jumping colors (9 speeds)

95-99

No function

100-149

8 fading colors (5 speeds)

150-154

No function

155-166

Red + Green, 0-100%

167-178

Green + Red, 100-0%

179-190

Green + Blue, 0-100%

191-202

Blue + Green, 100-0%

203-214

Blue + Red, 0-100%

215-226

Red + Blue, 100-0%

227-238

RGB, 0-100%

239-250

Blue + Red 0-100%, green 100-0%

251-255

Master RGBW output 100%

Auto

0-127

No function

128-255

Auto

Reset

0-250

No function

251-255

Reset (after 3 seconds on the same

value)

Installation and maintenance

Mounting the bracket

The included omega-type bracket is designed for this movinghead and makes it easy to mount en

remove a mounting hook to your fixture. A G-clamp, halfcoupler or triggercoupler can be mounted to

the omega bracket, which on his turn can be mounted to the fixture with quick-lock fastners. With a

clockwise rotation of 90 degrees, the omega-type bracket is mounted to the fixture. When using the

omega bracket, a safety cable must be connected to the safety eye of the fixture. For more

information, see the graphic instructions below.

1. Omega-type bracket

2. Clamp (Triggerclamp, not included)

3. Safety cable

4. Quick-lock fastners

Cleaning

Make sure to clean the exterior of the unit frequently, as the build-up of dust and dirt may have

negative effects on the cooling and optics of the fixture.

The exterior (plastic parts) of the unit can be cleaned with a damp cloth. The optics of the fixture can

be cleaned with a clean cloth or paper towel, with the addition of a non-aggressive glass cleaning

solution.

Clean the fan outlet and the cooling vents with a small brush, while using vacuum cleaner suction to

remove any loose dust and/or dirt.

Clean the exterior of this fixture once a month. When using this fixture intensively, the frequency of

maintenance needs to be increased.

Transport

When using this fixture in mobile setups, provide sufficient protection during transport. Use the original

packaging of this unit, or use a professional flightcase with proper foam inlay. This way the electronics,

optics and housing are protected against severe shocks, exterior damage and failing electronics.

Make sure the moving parts of the movinghead (pan and tilt motors) are secured during transport.

Shocks and fierce movement of the pan and tilt stepping motors may cause permanent damage.

After use, let the unit cool down for at least 10 minutes. When using DMX, use the ‘black out’ option on

your DMX controller. This way the unit is positioned in a static stand-by mode and the internal fan is

able to cool down the internal electronics, which decreases the chance of damage during transport.

Replacing the internal fuse

First check whether a failing power supply may be the cause of malfunction. When you suspect that

the internal fuse is broken, the fuse can be replaced by removing the fuse cover, located directly below

the power inlet.

WARNING: Before changing the fuse, always disconnect the fixture from your wall outlet or any other

power supply to prevent electric shocks.

Always replace a broken fuse with a fuse that has the same type and rating. After the fuse has been

replaced, always close the fuse-cover. Reconnect the fixture to your power supply and check whether

the problem is solved. When this does not solve your problem, contact your local dealer for help.

IMPORTANT: A spare fuse is located inside a special compartiment of the fuse holder.

Spare parts

This unit has no user serviceable parts inside. When any damage to internal components occurs,

contact your local dealer or a specialized technician in order to repair the fixture.

Checkup

To prevent dangerous situations, make sure your fixture is in optimal condition before using it. Check

your fixture frequently by using the following checklist:

- All screws must be mounted tightly.

- Check all screws and metal parts for corrosion. No visible corrosion may be present.

- The exterior of your fixture must be in optimal condition. Check your fixture for dents, cracks or

missing parts.

- Your installation spot must be in optimal condition. Check your installation spot for corrosion, cracks,

dents and strength.

- Electrical components (connectors and cables) must be in optimal condition. Any form of damage

(cuts, exposed wire cores or any other visual deformities should not be present.

If any visual or mechanical damage is detected, contact your local dealer or a specialized technician.

Do not use a damaged or failing fixture.

Connectors and wiring schematics:

DMX-connections: Electrical wiring:

Technical specifications

- RGBW LED beam movinghead

- 108x 3 Watt high power Edison LEDs, spread over red (24), green (28), blue (28) and white (28)

- expected lifespan LEDs: 50.000h

- low power consumption

- 8-bit smooth and precise pan and tilt movement

- 540 or 630 degrees pan, 270 degrees tilt

- scan position memory function with autocorrect

- RGBW color mix system

- LED shutter (electronic)

- LED dimmer (0-100% variable)

- LED rainbow effect

- LED macro effect

- LED strobe effect (0-18 Hz) with pulse

- master dimmer + dimmer for each color

- 12 DMX channels

- 2x16 character LCD display with blue backlight

- display auto dim function when not used for 30 seconds

- power requirements: 90-240V AC, 50/60 Hz

- power consumption: 120W (stand-by), 344W (max.)

- dimensions: 350 x 260 x 350 mm

- packing dimensions: 425 x 295 x 400 mm

- net weight: 9 kg

- gross weight: 11 kg

Connectors:

- DMX: 3p XLR male and female

- Power: Twist-lock connector (power cable to Schuko included)

Included accessories:

- Mounting bracket

- XLR-XLR signal cable

- Twist-lock to Schuko power cable

- Safety cable

Inhaltsverzeichnis

Andere Ayra Leuchte Handbücher

Ayra

Ayra Armageddon 648 RGB LED Bedienungsanleitung

Ayra

Ayra ITA COMPACT series Bedienungsanleitung

Ayra

Ayra Ero Minibeam 12 Bedienungsanleitung

Ayra

Ayra ERO 540 MKII Bedienungsanleitung

Ayra

Ayra ERO 030 Bedienungsanleitung

Ayra

Ayra Compar Kit Jr. Bedienungsanleitung

Ayra

Ayra LED Tri-Bar 12 Bedienungsanleitung

Ayra

Ayra TDC Diamond Scan Bedienungsanleitung

Ayra

Ayra Flash 150 Bedienungsanleitung

Ayra

Ayra IntenZ CB700 Bedienungsanleitung

Ayra

Ayra TDC Acid Bedienungsanleitung

Ayra

Ayra TDC 180 Derby Bedienungsanleitung

Ayra

Ayra ERO L90 Bedienungsanleitung

Ayra

Ayra Armageddon 648 W LED Bedienungsanleitung

Ayra

Ayra TDC HYBRID BEAM Bedienungsanleitung

Ayra

Ayra ERO Motion Heads 1W Bedienungsanleitung

Ayra

Ayra IntenZ CB600 Bedienungsanleitung

Ayra

Ayra TDC Flower Power Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung