An explanation of all available functions can be found below
ADDR With this function, you can determine the DMX start address of the device. Set it channel 001, and
the device will respond to DMX channel 1. Set it to channel 003, then the device will respond to DMX
channel 3 and so on.
CHND DMX channel mode allows the selection of ‘X’ number of channels with which certain functions of the
device can be operated. For certain functions, a simple, limited channel mode can be used while others will
require more extensive modes for optimum functionality.
SLND Using the Master / Slave Mode, it’s possible to connect several devices of the same type with one
another, via DMX 3 pin XLR cables so that they perform exactly the same movements and functions at the
same time. Therefore, single devices do not respond individually (or chaotically) and this results in a
completely coordinated show. In the Master / Slave function, the first device in the circuit does not receive
DMX signal.
PLEASE NOTE: When Slave mode is activated, the device shall wait for a signal from the designated Master
device. Selecting a automatic or sound controlled mode is then not possible! To cancel the Slave mode,
enter the ‘SLND’ menu and select ‘NAST’. This then sets the device to Master mode and the stand alone
functions can then be activated once more.
SHND Within this mode, a number of automatic programs can be selected, the settings of which you have
full control over. There are 15 programmes to choose from (where programme ‘0’ is a random show) and the
speed of each show can be adjusted. In this mode, the Sound Controlled function must be switched off. If it
is switched on, the unit will only respond to sound registered via the in built microphone.
SOUN Here, the in built microphone can be set to On or Off.
SENS This mode allows you to set the sensitivity of the in built microphone. The further the device is
installed from the sound source, the higher the sensitivity of the microphone needs to be so that the sound is
registered and the device responds accordingly and in time to the music. The microphone is able to
withstand high sound pressure. However, if the sound is loud and the sensitivity is high, the microphone will
find it more difficult to register the beat. Experiment with the sensitivity and distance from the positioning of
the device to make sure you’re getting the best possible signal and optimum performance.
MANU In this mode, the device can be used as a standard stroboscope. Both the strobe speed and
dimming levels can be set manually. In this mode, it’s also possible to illuminate the device continually and
without flashes.
PLEASE NOTE: In order to use this function, all automatic shows in the SHND menu must be set to ‘Off’. If
the SHND is set to ‘On’, the device shall automatically switch to that mode.
LED When the LED display is not in use, it can be switched off. By setting ‘LED’ to ‘Off’, this will prevent red
symbols from illuminating when the device is being used in dark spaces. If you press of the menu buttons,
the display shall immediately light up and show all necessary information. If the display is not used, it shall
automatically switch off again within 30 seconds.
DISP This function is useful when the device is suspended and the display screen is upside down. Use this
function to flip the screen so that it can be easily read when the device is suspended.
TEST When the device needs to be checked, use the ‘TEST’ function to test one or more devices at the
same time. The device(s) shall continuously runs through a programme within which the LEDs are tested so
that any deviations or defects can be easily detected. The device shall continue to repeat the programme
until it is manually interrupted (when you switch the device to sound control, for example).
INFO When the device is used professionally, or has been rented, it is important to carry out general
maintenance on a regular basis and the device is inspected before and after use. The ‘HOUR’ function
shows the number of hours that the device has been active. This number counts the usage automatically and
cannot be adjusted or manipulated. There is also a ‘VER’ function which displays the current firmware
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -
