SET
MODE
3
4
5
6
8:00
1
2
1
1
P1
P2
P3
1234567
START
1 2 3
2
1
3
4
7
6
5
P1
Current time
1234567
Days of
the week
Clock
12345
6789 10
11 12 13
Setting the Duration Time 14 15
Features
Connects to two separate valves
Up to three operations per day
Easy installation and programming
Waterproof and weather resistant
Battery powered; no need for electrical
hookup.
Getting Started
Parts Identification
1. Top cover
2. Controller Display
3. Solenoid
4. Controllor
5. Water flow direction
arrow
6. Hydraulic valve
This section gives a brief description of the
Controller buttons. See the following
sections fro further details.
MODE button – Quick presses of the
MODE button turn the controller on or off.
Longer presses of the MODE button put the
Controller in programming mode.
SET button - Press the SET button to set
a function and proceed.
Use these buttons to increase and
decrease schedule functions, or
select / deselect functions.
Installing connectors wires
G75
2V
1. Strip wire 1/2”.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
together with ends even, lead stranded
wire slightly.
4. Twist connector onto wires pushing
firmly until hand-tight. DO NOT torque.
5. Swipe excess sealant in and around
conductors. DO NOT REUSE.
Installing the Connectors
NOTE:Can only open one valve at a time.
The valves are indicated as P1 and P2.
If the controller is correctly wired, continue
the installation process as follows:
Turn off the main faucet.
1.
2.
Basic Controller Functions
Install the valve in the irrigation system
so that the black arrow on the valve is
pointing in the direction of the water
flow. The controller may be swiveled
around to faciliate installation.
Occasionally the valve opens in transit. To
ensure that the valve is closed before you
open the main faucet, first make sure that
the controller is not set to OFF (If it is set to
OFF, press briefly on the MODE button to
turn on).
3. Press and SET simultaneously.
P1 will flash.
4. Press SET to select P1 or to
select P2.
5. Press SET and to close the
valve.
You are now ready to program the
controller.
6. Turn on the main faucet.
To manually open the valve, make sure that
the controller is in operating mode and press
and SET simultaneously.
P1 will flash. Press SET to select P1 or
to select P2 and then SET.
Manual Function
The irrigation will continue until the interval
defined has passed. If the irrigation duration
has been set to zero, the valve will close
after one minute.
To stop irrigating, press and SET
simultaneously.
Irrigation schedule design table
Sun. Mon. Tues Wed. Thu. Fri. Sat.
P1
P2
Selected Starts
Irrigation Days
Irrigation Star Times
Irrigation Duration for valve 1 (P1) and
valve 2 (P2)
Start 1 Start 2 Start 3
Start times for P1 and P2
Duration time
Selected Starts for P1
Selected Starts for P2
Start 1 Start 2 Start 3
P1
P2
Programming the Controller
Meaning of Controller Icons
NOTE: Quick presses of the MODE button
on or off. Longer presses of the MODE
buttton put the controller in programming
mode.
1. Irrigating days of
the week.
2. Program starts.
3. P1 is Valve 1,
P2 is Valve 2
4. Irrigation
5. Timing or clock
6. Low battery
7. Time adjustment
Setting the Clock
If screen is blank, press MODE to activate.
Before programming the controller you
must set the clock.
1. Press MODE for several seconds until the
time adjustment icon appears. (The
minutes will be flashing):
On this screen the numbers represent the
current time.
2. Use the and the buttons to adjust
the minutes.
3. Press SET to continue.
4. Use the and the buttons to
adjust the hours.
5. Press SET to continue.
6. Use the and the buttons to select
the current days of the week. The selected
day will flash.
7. Press SET to return to operating mode.
After setting the clock,
1. Two long presses on the MODE button
makes the following screen appear:
On this screen, the clock numbers refer to
the time you wish irrigation to begin. There
are three start times which are the same for
both valves (P1 e P2).
Setting the Start Times
2. Use the and the buttons to adjust
the minutes.
3. Press SET to continue.
4. Use the and the buttons to adjust
the hours.
5. Press SET to return to start time 2, and
repeat steps 1-3 for start times 2 and 3.
Setting the Irrigation Program
The irrigation program must be set for each
valve separately (P1 e P2).
The strat times are common for both valves as
instructed in the previous section. Each valve
may be set with different duration time,
different start selects, and different days of
operation.
1234567
START
1
1. Press 3 long presses on the MODE button
until the following screen appears (The
minutes will be flashing):
On this screen, the clock numbers refer to
the irrigation duration of Valve 1.
2. Use the and the buttons to adjust
the minutes.
3. Press SET to continue.
4. Use the and the buttons to adjust
the hours.
5. Press SET to continue.
1234567
START
1
P1
On this screen, you select the Starts you
wish to irrigate with Valve 1 (P1). Start 1
will flash.
1. To select Start 1, press and then
SET and Start 2 will flash.
OR
2. To deselect Start 1, press and then
SET and Start 2 will flash.
3. Repeat fro Start 2 and 3.
The Select Day screen appears. Day 1
will flash.
The Select Day screen appears after the
Start times have been programmed
(as in section 12).
1. Press SET to reach the day you wish
to irrigate. The number (corresponding
to the day of the week) will flash.
2. Press to select that day (the square
which appears indicates day is
selected).
3. Press to deselect a day.
4. Press SET until all days are
programmed as desired.
5. Press SET to return to operating mode.
P1 programming is now complete. Four
long presses on MODE will begin the
programming for P2.
Setting the Days
1234567
P1
Follow the instructions for Setting the
Irrigation Program (section 10).
Example
If you wish to irrigate with Valve 1 (P1) on
Sunday, Tuesday, Thursday and Saturday at
06:00 in the morning for 15 minutes:
Make sure the clock is set, and you are in
operating mode. Then press MODE twice to
get to the Start Times. Set Start 1 to 6:00
(factory default). Press MODE three times to
set duration time. On the following screen,
select Start 1, and deselect Starts 2 and 3.
On the following screen select days 1, 3, 5
and 7. At the same time, you may program
Valve 2 (P2) to irrigate for 30 minutes at
13:00 on Monday and Thursdays. Start time
are the same for both valves, but Start 2 is
not in use for P1 in this example, so you
may program Start 2 to the desired time of
13:00.
Press MODE twice to get to the Start Times.
Press SET until Start 2 is selected, and
adjust time to 13:00. Press MODE four times
to tset the duration time for P2. On
the following screen, deselect Start 1, select
Start 2 and deselect Start 3. On the next
screen, select days 2 and 4.
It is possible to make a seasonal adjustment
to the irrigation duration for both valves as
necessary. The minimum adjustment is 10%
of the programmed duration, and the
maximum is 200%.
Seasonal Adjustment
Seasonal Adjustment
Setting the Irrigation Program
To set the irrigation program, you must be in
an operating mode.
First program P1 as follows:
The P1 start screen appears:
Selecting the Starts
Sol.1
Sol.2
Green
Green
Green
Black
Black
Black
Red
