BALCO KOG6789 Bedienungsanleitung
.
MODEL NUMBER: KOG6789
INSTRUCTION MANUAL
.
.
.
.
Warranty Note
If you experience any issues with this product, or it’s
performance is not what you had expected, please contact
us at Balco Lifestyle before returning the item to the store.
It is likely that we can resolve any problems for you via
phone or email.
We can be reached on:
Phone: 1300 663 907 (Mon - Fri; 8:30am - 6:00pm EST)
Email: customercare@balcolifestyle.com.au
Web: www.balcolifestyle.com.au
Important
Getting the most out of your 3D Printer:
Read the manual carefully
It will help you get set up with ease
Visit www.balcolifestyle.com.au
We’ve got additional support videos and guides
Call After Sales Support - 1300 663 907
Available Monday - Friday, 8:30am - 5:30pm AEST
Email customercare@balcolifestyle.com.au
We’re always happy to help
.
.
Warranty Details
AFTER SALES SUPPORT
1300 663 907
This product is warranted against defects for a period of 1 year. If the product is faulty, Balco will repair or
replace the product (at its discretion) at no cost to you provided the product has been used in accordance with
instructions provided. The benefits conferred by this warranty are in addition to other rights and remedies
under consumer law in relation to these goods.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
To Make a Warranty Claim
This product warranty is provided by Balco Lifestyle, PO Box 537 Bayswater Business Centre, Victoria,
Australia, phone 1300 663 907. If a defect appears within the warranted period, you are entitled to claim a
warranty.
Contact Customer Care
Phone: 1300 663 907
Address: Balco Lifestyle, PO Box 537 Bayswater Business Centre, Victoria, Australia
When making a return, contact Balco Lifestyle via phone or email to register your claim and identify the fault.
You will be responsible for any expenses associated with making a claim under this warranty (including
postage). When returning a faulty product, please include your contact details, the original or copy of your
proof of purchase, explanation of the fault and ensure the product is properly packaged to ensure no damage
occurs during transport.
Upon receipt of your of your valid warranty claim, a replacement will be issued sent to your nominated address
at no cost to you.
.
.
5
Warranty Details
AFTER SALES SUPPORT
1300 663 907
This product is warranted against defects for a period of 1 year. If the product is faulty, Balco will repair or
replace the product (at its discretion) at no cost to you provided the product has been used in accordance with
instructions provided. The benefits conferred by this warranty are in addition to other rights and remedies
under consumer law in relation to these goods.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
To Make a Warranty Claim
This product warranty is provided by Balco Lifestyle, PO Box 537 Bayswater Business Centre, Victoria,
Australia, phone 1300 663 907. If a defect appears within the warranted period, you are entitled to claim a
warranty.
Contact Customer Care
Phone: 1300 663 907
Address: Balco Lifestyle, PO Box 537 Bayswater Business Centre, Victoria, Australia
When making a return, contact Balco Lifestyle via phone or email to register your claim and identify the fault.
You will be responsible for any expenses associated with making a claim under this warranty (including
postage). When returning a faulty product, please include your contact details, the original or copy of your
proof of purchase, explanation of the fault and ensure the product is properly packaged to ensure no damage
occurs during transport.
Upon receipt of your of your valid warranty claim, a replacement will be issued sent to your nominated address
at no cost to you.
Safety Instructions
Before you get started, please read these important safety instructions.
CAUTION: The Balco 3D Printer generates high temperatures and includes moving parts that can
cause injury. Never reach inside of the Balco 3D Printer while it is in operation, and allow time for
the printer to cool down after operation.
Vapours/fumes may be irritating at operating temperatures. Always use the Balco 3D
Printer in an open, well ventilated area.
Do not leave the Balco 3D Printer unattended during operation
Contact with extruded material may cause burns. Wait for printed objects to cool before
removing them from the build platform.
Always take care when using the Scraper. Never direct the Scraper towards your ngers.
• The printer must not be exposed to water or rain, or damage will occur.
• The printer is designed to be used with ambient temperature ranging 15°C - 30°C, and humidity
ranging 20% - 50%. Operating outside these limits may result in low quality models.
• In case of emergency, turn o the 3D printer at the power outlet.
• It is recommended that you use eye protection when cleaning/sanding printed models to avoid
small particles contacting eyes.
HOT SURFACE MOVING PARTS
.
6
Contents
Warranty Details 4
Safety Instructions 5
Parts List 8
Technical Specications 9
Product Overview 10
Printer Front View 10
Printer Rear View 11
Print Bed 12
Control Box 13
Quick Guide 14
Construct and Connect 14
Levelling the Bed 15
Printing a File 16
Introduction 18
1.1 What is 3D Printing? 18
1.2 From 3D Design to Printed 3D Object: 18
1.3 Good 3D Printing Practices 20
Installation 21
1.4 Unboxing and Assembly 21
1.5 Control Panel 23
1.5.1 Main Display 23
1.5.2 Menu Map 23
1.5.3 Default Conguration 25
Setup 26
2. Levelling the Heated Print Bed 26
3. Filament 27
3.1 Filament Types 27
3.2 Inserting Filament: 28
3.3 Removing Filament: 29
3.4 Storage: 29
4. Using the Micro SD Card 29
4.1 Loading les from your Computer: 29
4.2 Printing from the Micro SD Card: 30
5. Removing 3D Objects from the Bed 30
.
7
Using Cura 31
6. Creating a GCODE File using Cura 31
6.1 Installing Cura 31
6.2 Adding your Balco 3D Printer to Cura 32
6.3 Loading a 3D Design into Cura 32
6.4 Viewing and Positioning your 3D Model in Cura 32
6.5 Quick Print Settings 35
6.5.1 Exporting your GCODE File: 36
6.6 Advanced Print Settings 36
6.6.1 Basic Tab Options 36
6.6.2 Advanced Tab Options 39
6.6.3 Plugins Tab 42
6.6.4 Start/End GCODE Tab 42
6.6.5 Expert Settings 43
Servicing 48
7. Servicing your 3D Printer 48
7.1 Replacing the Print Mat 48
7.2 Nozzle Cleaning 48
7.3 Routine Component Check 49
7.4 Storing 49
Finishing 50
8. Finishing Techniques 50
8.1 Useful Tools/Equipment 50
8.2 Removing Support Material 50
8.3 Sanding 51
8.5 Surface Coating 51
Troubleshooting 52
9. Troubleshooting 52
9.1 Printing Problems 52
10.2 Connectivity Problems 53
10.3 Other Problems 54
10. Useful Terms 56
Appendix 58
References 58
.
8
Parts List
1 x Balco 3D Printer (Control
Box, Extruder Tower, Heated
Print Bed)
1 x Filament Spool Holder
1 x Filament Spool Stand
1 x Power Cable
1 x USB Cable
1 x 4GB MicroSD Card
1 x Scraper
1 x PTFE Tube
1 x Hex Key Set
6 x Hex Bolts
2 x Cable Ties
4 x 10m PLA Filament
2 x Print Bed Mats
2 x 0.4mm Drill Bits
1 x Instruction Manual
1 x Getting Started Guide
1 x Warranty Card
.
9
Technical Specications
Printing
Print Technology: Fused Filament Fabrication (FFF)
Build Volume: 200 x 200 x 180mm
Layer Resolution: 0.1 – 0.4mm
Positioning Accuracy: X 0.012mm
Y 0.012mm
Z 0.004mm
Extruder Quantity: Single Extruder
Extruder Diameter: 0.4mm
Print Speed: 10mm/s - 70mm/s
Travel Speed: 10mm/s - 70mm/s
Supported Print Materials: Balco Branded PLA, ABS, PVA,
HIPS, PLA Wood, PLA Flex, Conductive
Temperature
Ambient Operating Temperature: 15°C – 30°C
Operational Extruder Temperature: 170°C - 260°C
Operational Print Bed Temperature: 30°C - 120°C
Software
Slicer Software: Cura V14.07
Cura Input Formats: .STL, .OBJ, .DAE, .AMF
Cura Output Format: .GCODE
Connectivity: Micro SD Card, USB port (Expert users only)
Electrical
Input Rating: 100-240V AC, 50/60Hz, 3.5A
Physical Dimensions
Printer Frame Dimensions: 400 x 410 x 400mm
Weight: 10KG
.
10
Product Overview
Printer Front View
1. X Rail
2. X Belt Drive
3. Extruder Spring Lever
4. Extruder Cooling Fan
5. X Stop (Micro Switch)
6. Filament Cooling Fan
7. Extruder Driving Motor
8. Filament Spool Holder
Assembly
9. Tower Frame
6
2
9
8
1
4 7
3
5
.
Inhaltsverzeichnis
Andere BALCO 3D-Drucker Handbücher
