BaltLED CROWN DUO R21 Bedienungsanleitung

CROWN DUO R21 INSTALLATION GUIDE

READ THE INSTRUCTIONS CAREFULLY BEFORE MOUNTING

CONNECTION SCHEME

! 29 pcs - max number of modules in one chain when the power supplied from single end.

! String end voltage can’t be less than 11V, do not exceed specified module string length

POWER SUPPLY

QUANTITY OF MODULES* 2 m* 5 m* 10 m*

min max mm2AWG mm2AWG mm2AWG

BP3

-C700-34.1 314 0.5 26 0.5 26 0.5 26

* When connecting two chains parallel with even number of modules in each chain

**Distance between power supply and modules.

! Power loss less than 5%.

! Recommendations for optimal use of power supply.

1/2

POWER SUPPLY LOAD RECOMMENDATIONS

www.baltled.com

9th August, 2018

STORAGE AND MAINTANANCE CONDITIONS

MOUNTING AND USING RECOMENDATIONS

•Be careful not to go beyond recommended maximum quantities of modules for a power supply. Overload may cause blinking or a failure.

•Any type of self tapping screws can be used for mounting.

•These modules are designed to work with constant-current power supply. Use only recommended power supplies, do not connect to a constant-voltage

power supplies as it will cause immediate failure of modules.

•Before installing make sure, that the fixing area can bear the total weight of the modules.

•Please install LED modules with appropriate cables. There is a possibility, that cables may get disconnected due to contractions, caused by

temperature changes.

•Please check that sulphur constituent is not contained in used components when the module is installed.

•Make sure to install modules in a place with a sufficient breathability in order to prevent lifetime reduction by heat. Operating temperature should not

exceed +50 ºC.

•When installing a module in a fixture (signboard), make sure to provide ventilation for constituent sulphur, drainage for rain water to prevent aged

deteriorations.

•When fixing cables of the modules do not use metal cable stop. The tunic of the cable may be damaged and therefore lead to short-circuited.

•Be sure to install modules at a maintainable place.

•In order to prevent LED from breaking down caused by static electricity, make sure not to touch the metal parts of the cable directly with bare hands.

•Make sure to apply correct polarity and direction of the modules. If mistaken, it will lead to failure and break down of the modules.

•When trying to perform lighting test (burn-in test), be sure to connect module to a power supply. Modules can fail to light up due to over-current. If the

power supply is turned on without LED modules connected, modules can be connected only 5 minutes after the power supply has been turned off.

Residual electricity may cause damage to modules.

•Avoid applying force while bending, twisting or pulling the power supply cables to minimize the risk of electrical shock.

•If any signs of smoke or the smell of burning plastic occurs, turn off modules immediately and investigate the power supply and the wiring carefully.

•Make sure to record and keep product lot and installation date of the modules.

•Before the maintenance, turn off the power and maintain the modules after modules cool down. Otherwise, electric shock or burn may occur.

•Do not pull the wiring while removing the modules to prevent possible disconnections.

•Make sure to store modules at dry places, avoid elevated temperatures, high pressures, vibrations, corrosive or combustive gas, direct sunlight.

•Do not wipe or spray modules with volatile materials, such as thinner or benzene as it may lead to combustion and malfunctioning.

•Modules cannot operate at presence of materials containing sulphur components or where sulphur containing gas is generated as it leads to changes in

light color and malfunctioning.

CROWN DUO R21 INSTALLATION GUIDE

GENERAL CONDITIONS

•Installation of modules must carried out by a qualified technician according to handling standards of electrical equipment.

•Modules and power supply have absolute maximum rating. Comply with the specifications to avoid failures or combustion.

•Avoid placing any high temperature objects around the modules, also avoid putting cloth or paper on the modules. It may lead to combustion, burnout,

overheat, failure, deformation.

•Modules cannot be used in high-temperature environments, also they must not be subjected to vibration, shock, particles, corrosive or combustive gas.