Band-it 60FM Bedienungsanleitung

Model No: __________________________

Serial No: __________________________

DEALER:

Name: _____________________________

Address: ___________________________

City/State: __________________________

Phone No: __________________________

Delivery Date: _______________________

MODEL 60FM / 72FM

OPERATING & PARTS MANUAL

6750 Millbrook Rd. • Remus, MI 49340 • 1-989-561-2270

MANUFACTURED BY BANDIT INDUSTRIES, INC

PHONE: (989)561-2270

PHONE: (800)952-0178 IN USA

FAX: (989)561-2273 ~ SALES DEPT.

FAX: (989)561-2962 ~ PARTS/SERVICE

WEBSITE: www.banditchippers.com

ATTENTION:

Depending on what replacement parts you are ordering, we will need the following information:

ATTACHMENT COMPONENTS

Serial Number

Model Number of Attachment

Serial No:

DEALER:

Name:

Address:

City/State:

Phone No:

Delivery Date:

WARNING

ADVERTENCIA

Breathing diesel engine

exhaust exposes you to

chemicals known to the

State of California to cause

cancer and birth defects or

other reproductive harm.

• Always start and

operate the engine in a

well-ventilated area.

• If in an enclosed area,

vent the exhaust to the

outside.

• Do not modify or tamper

with the exhaust system.

• Do not idle the engine

except as necessary.

For more information go to:

www.P65warnings.ca.gov/diesel

Respirar gases de escape de

motores diesel le expone a

quÍmicos conocidos por el estado

de California como causales de

cáncer y defectos congénitos u

otros daños reproductivos.

Para mayor informaciÓn visite:

www.P65warnings.ca.gov/diesel

• Siempre encienda y opere el

motor en áreas bien ventiladas.

• Si está en un área cerrada,

ventile escape hacia el exterior.

• No modiﬁ que ni altere el

sistema de escape.

• No deje el motor en ralentÍa no

ser que sea necesario.

SPW-46 8/18

SPW-47 8/18

Cancer and

Reproductive

Harm

WARNING

ADVERTENCIA

Cáncer y daño

reproductivo

www.P65warnings.ca.gov

CALIFORNIA PROPOSITION 65



WARRANTY VALIDATION FORM

(BANDIT TRACK CARRIER)

PURCHASER / OWNER INFORMATION:

Company Name __________________________________ Contact Name _____________________

Mailing/Street Address _______________________________________ City _______________________

State ___________________ Zip Code _______ Country ______________ Telephone Number(__) ________

E-mail ____________________________ Machine Model No. _______ Date Put Into Service ______

Machine Serial No. ____________________ Machine Work Order No. ________ Machine Hours _______

Engine Make _________________ Engine Serial No. __________________ Machine Color _______

DEALER / SELLER INFORMATION:

Dealer/Seller Name _______________________________ Contact Name _____________________

Mailing/Street Address _______________________________________ City _______________________

State ___________________ Zip Code _______ Country ______________ Telephone Number( __) ________

IMPORTANT - WARRANTY WILL BE DEEMED NULL AND

VOID IF THIS FORM IS NOT FILLED OUT COMPLETELY AND

ACCURATELY AND RETURNED TO THE CUSTOMER DATA

DEPARTMENT WITHIN 10 DAYS OF EQUIPMENT DELIVERY

I have inspected this equipment and nd it in correct working condition. To the best of my knowledge,

the customer and his/her personnel are aware of, and agree to the above procedures.

Signed: ________________________________________________________ Date: ______________

(Dealer Representative)

The equipment has been thoroughly checked by the above named dealer representative, and I am

satised with his/her instructions. I have also read, understand, and agree to reverse side of page.

Signed: ________________________________________________________ Date: ______________

(Customer)

1. _____ The customer has received instruction and fully understands all operational, safety and maintenance

requirements of the equipment.

2. _____ The customer has received instruction and fully understands that everyone needs to stay back 300 feet (90

m) in all directions of machine while in operation. Failure to do this could result in severe injury or death.

3. _____ The customer has received instruction and fully understands the equipment maintenance schedules and

procedures. The customer understands that it is their responsibility to perform scheduled maintenance that includes

retightening all fasteners as needed, belt adjustments, lubrication and other items.

4. _____ The customer has received instruction and fully understands not to reach near cutter head with hands or

feet or to be located near debris eld with engine running.

5. _____ The customer has received instruction and fully understands that the operators must always be located

within easy reach of all feed control and shut down devices.

6. _____ The customer has received instruction and fully understands purpose of and how to operate the shut down

and shut-o󰀨 devices, and will not attempt to override any safety devices or guards.

7. _____ The customer has received instruction and fully understands to not start grinding or mowing without checking

for power lines, water lines, sewer lines, phone lines, etc. in the area above or below the ground level.

8. _____ The customer has received instruction and fully understands that before performing any maintenance

on the machine the ignition key must be removed, the cables must be completely disconnected from the battery,

the cutter head must have come to a complete stop, and be securely on the ground before performing any type of

maintenance on the machine. The customer understands they must allow the necessary time for the cutter head to

come to a complete stop.

9. _____ The customer has received instruction and fully understands that the machine is not to be operated without

all safety devices installed and working properly; this includes guards, shields, deections chains, and other devices.

10. _____ The customer has reviewed and fully understands limited warranty, and all written and visual instructions.

11. _____ The customer has received instruction and fully understands that warranty will not apply if the machine is

operated with replacement parts or equipment not manufactured or recommended by Bandit Industries, Inc.

12. _____ The customer has received, been advised, and understands the manuals, and the Safety/Service video

supplied with the machine. A video is supplied for equipment models as available.

13. _____ All Danger, Warning and Operational decals are properly displayed on equipment and fully understood

by customer.

14. _____The customer has been instructed, understands, and agrees that all potential operators must: See the

supplied video, be instructed on all the Danger, Warning and Operational decals, read the manual and follow the

procedures.

Customer Data Department

6750 Millbrook Road

Remus, MI, USA 49340

Phone: (800) 952-0178 in USA

Phone: (989) 561-2270

Fax: (989) 561-2273

Website: www.banditchippers.com

All of the employees that build your equipment strive to manufacturer the very best quality product on

the market. We would appreciate your e󰀨orts in letting us know how we are doing.

We would like you to operate your machine for thirty (30) days and then ll out this questionnaire and mail it to us.

This will help us to keep producing a good product and improving our products through your recommendations.

DATE PURCHASE: ______________________

MODEL: ________________________________

SERIAL NUMBER: _______________________

DEALER NAME: ________________________

_______________________________________

TO BE RETURNED AFTER THIRTY (30)

DAYS OF OPERATION

Please return to: Customer Data Department

6750 Millbrook Road

Remus, MI 49340

Phone: (800) 952-0178 in USA

Phone: (989) 561-2270

Fax: (989) 561-2273

Website: www.banditchippers.com

STUMP GRINDER / FORESTRY MOWER

QUALITY REPORT

1. Did your machine perform to your expectations? _______________________________________

2. Was the machine delivered on schedule? _____________________________________________

3. Was the paint color and nish to your satisfaction? ______________________________________

4. Was machine equipment as ordered? ________________________________________________

5. Did all welds appear to be high quality? ______________________________________________

6. Was the overall machine to your liking? ______________________________________________

7. What problems have you experienced? ______________________________________________

8. Have any components regularly loosened that caused problems? __________________________

9. Does the hydraulic system seem to have adequate power? ______________________________

10. Is the machine manufactured to accommodate service in an adequate manner? If not, please explain:

_______________________________________________________________________________

11. General comments and/or suggestions: ________________________________________________

_______________________________________________________________________________

12. Would you like to be contacted concerning more of our equipment? ________________________

YOUR COMPANY: ________________________________

NAME: __________________________________________

ADDRESS: ______________________________________

CITY: ___________________________________________

STATE & ZIP: _____________________________________

PHONE: ( ____ ) _________________________________

E-MAIL: _________________________________________



Bandit

MODELS 60FM / 72FM TABLE OF CONTENTS

TABLE OF CONTENTS

ANY PART, PORTION, DESIGN, NUMBER, SPECIFICATION, AND/OR DIMENSION IN THIS

MANUAL IS SUBJECT TO CHANGE WITHOUT NOTICE BY THE MANUFACTURER.

NOTICE

PAGE

INTRODUCTION & WARRANTY ........................................................... 2

SERIAL NUMBER LOCATIONS ............................................................ 6

SAFETY PROCEDURES ........................................................................ 7

EQUIPMENT SPECIFICATIONS ........................................................... 11

DECALS ................................................................................................... 12

MACHINE OPERATION ......................................................................... 15

MAINTENANCE ...................................................................................... 18

HYDRAULICS ......................................................................................... 27

REPLACEMENT PARTS ........................................................................ 31

FORESTRY MULCHER COMPONENTS ....................................... 32

CUTTER HEAD TEETH................................................................... 34

HYDRAULIC COMPONENTS ......................................................... 35

SERVICE RECORD ................................................................................ 36

Bandit

INTRODUCTION & WARRANTY

INTRODUCTION

The purpose of this manual is to provide the user with specications and procedures for the

operation, maintenance and repair of this BANDIT product. As with any piece of equipment, safety

should always be a constant thought while the machine is being operated, serviced or stored.

In order to highlight this consideration, the material which addresses safety is proceeded by the

following signal words:

The equipment is designed and manufactured in accordance with the latest product industry

standards. This alone does not prevent injury. It is the operator’s responsibility to use good

judgement and follow the warnings and instructions as indicated in this manual, on the machine

and follow all safety standards per ANSI and OSHA instructions.

Improper use of the product can result in severe personal injury. Personnel using the equipment

must be qualied, trained and familiar with the operating procedures as dened in this manual,

prior to operating the product.

It is the responsibility of the owner or employer to ensure that the operator is trained and practices

safe operation while using and servicing the machine. It is also the owner’s responsibility to provide

and follow a regularly scheduled preventative maintenance and repair program on the product,

using only factory approved replacement parts. Any unapproved repairs or modications may

not only damage the machine and its performance, but could result in severe personal injury.

Unapproved repairs or modications will void warranty and eliminate manufacturer of any liability

claims. Consult the equipment manufacturer with any questions.

Each machine is shipped with a manual, a customer’s check sheet on the product, and any

available parts & service manuals on component parts not produced by this manufacturer.

Additional copies of these manuals and check sheets can be purchased from the manufacturer,

or through the dealer. Engine parts, service and maintenance manuals MUST be purchased

through the engine manufacturer or their dealer.

The producer of this Bandit product reserves the right to make any modications or revisions to

the design or specications of its machine without advance notice. The producer also reserves

the right to change machine and part prices as needed without advance notice.

NOTICE

WARNING

Signal Word Likelihood of Occurrence Degree of Potential

Injury or Damage

Will occur if warning is ignored

Can occur if warning is ignored

Will or can occur if warning is ignored

Important, but not hazard related

Severe

Minor

Minor to Severe

Severe

CAUTION

NOTICE

DANGER

WARNING

Bandit

MODELS 60FM / 72FM

TYPICAL SERIAL NUMBER AND/OR

WORK ORDER NUMBER LOCATIONS

1. Serial Number - in tool box compartment

2. Work Order Number - on back left hand corner

SERIAL NUMBER LOCATIONS

Bandit

MODELS 60FM / 72FM

Before starting the machine, take a minute to

check a few things. The grinder should be in an

area restricted from people passing by. This area

around the grinder must be free of all objects that

can obstruct your movement when working with the

grinder. The machine should be checked for loose

tools or foreign objects, especially in the grinding

area. All tools not in use should be secured in a tool

box.

Operators must at all times be located within easy

reach of all control and shut-o󰀨 devices when the unit

is running. They must be attentive and prepared to

activate the devices.

Torn or loose clothing is more likely to get caught

in moving machinery parts. Keep such items as long

hair, shirt sleeves, and shirt tails properly contained.

Avoid wearing necklaces, rings, watches, and

especially neckties while operating this machinery.

Make sure the machine is in excellent condition, and

all the guards are in place, tight and secure.

Wear all personal protection equipment and follow

all safety standards per ANSI and OSHA instructions.

Examples of equipment: hard hat, face shield, safety

glasses, gloves, ear protection, etc. Always keep a

fully charged re extinguisher with the machine while

operating or servicing the machine.

SAFETY PROCEDURES

The words Danger, Warning, Caution, and

Notice are used on the safety decals and throughout

this manual, to make you aware of the safety

procedures. These procedures are very important,

read and obey them.

YOUR SAFETY IS VERY IMPORTANT TO US!

This machine is equipped with safety decals,

guards and designs for your protection.

Don’t ever take the machine for granted, always be

cautious and careful when operating your equipment.

Read and follow all the instructions in your

manual thoroughly. Your safety is dependent on

your knowledge of how to operate and maintain this

machine. You may obtain additional copies of this

manual from your Bandit Dealer.

Before operating machine, you must have all

potential operators; read and understand manuals

and decals, watch the video and follow the

recommendations.

Regardless of how hard a manufacturer tries to

produce a safe machine, accidents still happen.

Normally accidents are caused by people making

mistakes. They do not read the manual, they ignore

warning decals or do not use lockouts provided for

their safety. This normally happens after the person

has become accustomed to the machinery. In the

initial start up and operation of the machinery, they

are cautious, they are very careful because they do

not understand the machine.

This equipment is intended for use by personnel

who are experienced with similar equipment. Always

operate safely. There must be at least two qualied

and trained operators at the work site. They must be

positioned in safe working locations, following safety

procedures and instructions, and aware of each

others whereabouts. There must, also, be at least

two people on site during maintenance and service

procedures in case an accident should occur. Never

operate any machine while under the inuence of

drugs or alcohol.

Keep children, bystanders and animals clear of

working area. Never operate equipment that is in

need of repair or adjustment.

! ! !

DANGER

WARNING

NEVER sit, stand, lay, climb or ride anywhere

on this machine while it is running, operating, or in

transit. You will be injured.

DANGER

Bandit

MODELS 60FM / 72FM

Do Not enter or exit the operator’s cab unless:

the cutter head has come to a complete stop, the

cutter head is setting on the ground, and the ignition

key is in the operator’s possession.

DANGER

SAFETY PROCEDURES

It is very important after you have operated a new

machine for approximately an hour to shut down the

machine and recheck all nuts and bolts. It is normal

for nuts and bolts to loosen once on a new piece of

machinery. If you tighten them now, there is a good

possibility they won’t loosen again. Certain nuts and

bolts should be checked periodically such as cutter

teeth bolts, etc. for torque and t.

Most of the nuts used on the machine are self

locking. After a nut or bolt has been removed

ve times, it should be replaced to ensure proper

tightness. This is especially critical on the cutter tooth

bolts!

After the engine is started, let the grinder tooth

turn at the lowest RPM’s possible. Listen for any

type of noise that is foreign. Any steel on steel noise

is foreign. If you hear a noise, stop the engine, nd

the problem and x it.

It is very important after you have operated a new

machine for approximately an hour to shut down the

machine and recheck all hydraulic ttings. Retighten

as needed.

DO NOT GO NEAR HYDRAULIC LEAKS! High

pressure oil easily punctures skin causing serious

injury, gangrene, or death. Avoid burns from uid.

Hot uid under pressure can cause severe burns.

DO NOT use ngers or skin to check for leaks. Lower

load or relieve hydraulic pressure before loosening

ttings. Relieve all pressure in the system before

disconnecting the lines, hoses, or performing other

work. Use a piece of cardboard to nd leaks. Never

use your bare hands. Allow system to cool down to

ambient temperature before opening any coolant or

hydraulic oil system.

In cold weather situations let your hydraulic

system idle for approximately 15 minutes to allow

the system to warm up to operating temperature.

WARNING

Keep the machine in good condition. Be sure the

machine is in good operating condition and that all

safety devices, including guards and shields are

installed and functioning properly. Visually inspect

the machine daily before starting the machine. Refer

to the “Daily Start Up & Maintenance”. Make no

modications to your equipment unless specically

recommended or requested by Bandit Industries Inc.

DANGER

DO NOT operate this machine unless all hydraulic

control devices operate properly. They must function,

shift and position smoothly and accurately at all

times. Faulty controls can cause personal injury!

WARNING

SAFETY PROCEDURES

WARNING

Sparks can occur if cutter teeth strike rocks,

metal, or other hard objects.

DO NOT use in high or very high re hazard

severity zones.

Operation of this equipment may create sparks

that can start res around dry vegetation. A spark

arrester may be required. The operator should

contact local re agencies for laws or regulations

relating to re prevention requirements.

Do not attempt to engage the cutter head if

the cutter head is jammed or frozen in place. If

you do, you will damage or ruin the drive belts

and/or the hydraulic motors which will not be covered

under warranty and will cost you down time and

money.

NOTICE

Before attempting any type of maintenance, allow

cutter head to come to a complete stop, turn o󰀨 engine,

remove the ignition key from the skid steer, make sure

the ignition key is in your possession, disconnect the

battery to the skid steer. Make sure the cutter head is

setting on the ground or securely blocked up and also

chained before doing any work around or under it.

DANGER

Do Not let the cutter wheel come in contact with the

machine, this will damage the machine and may cause

severe injury or death. Do Not over tilt the cutter wheel,

this will damage the hydraulic hoses.

DANGER

WARNING

Make sure to lock the couplers

by twisting the sleeve at least 1/4

of a turn after connecting. Failure

to do this may result in damage

to component.

To disconnect, line up the

shoulder groove on the sleeve

with the detent ball.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Band-it Rasen- und Gartengeräte Handbücher

Band-it

Band-it STUMP GUN Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung