Bandai Namco RAZING STORM Bedienungsanleitung

The actual product may differ slightly from the illustrations in this manual.

●To ensure safe operation of the game machine, be sure to read this Operation Manual before use.

●Keep this Operation Manual in a safe place for quick access whenever needed.

DANGER

RAZING STORM

OPERATION MANUAL

RAZING STORM MANUAL

US/EUROPE

NOTE:SEE ADDENDUM FOR SPECIFIC EU INFORMATION.

Read PRECAUTIONS and INSTALLATION

Sections before operating game

IMPORTANT

RF Notice

Note: This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operating in a commercial environment. This equipment uses, and

can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communica-

tions. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

No part of this publication may be reproduced by any mechanical photographic,

or electronic process, or in the form of a photographic recording, nor may it be

stored in a retrieval system, transmitted, or otherwise copied for public or private

use, without permission from NAMCO BANDAI GAMES.

INTRODUCTION

Thank you for purchasing the “Razing Storm” game machine (hereafter referred to as the “machine”).

This operation manual describes:

How to install, operate, relocate, transport, maintain and discard the machine safely and

properly

How to operate the machine correctly and make full use of its features

How to ensure safety of players and bystanders

Inquiries regarding this machine and its repair

For further information about the machine and its repair, contact your distributor.

The software included in the machine is protected by copyright laws.

The software must not be copied, modied, distributed publicly, or used for purposes

other than the operation of this game machine.

Violators of copyright laws may be subject to criminal penalties.

Do not use the software storage media in any other game machine; otherwise, machine

malfunctions may result.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380;

5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending.

DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol

Visit http://www.bandainamcogames.co.jp/aa/am/vg/s357-license/ for other licensees and

trademarks.All other trademarks are the properties of their respective owners.

Notes:

On thelabels attachedto themachine and inthis operationmanual, precautionsregarding

safety and property damage are classied as shown below in accordance with the magnitude

of the particular risk.

:Failure to avoid the risk most certainly result in death or serious injury.

:Failure to prevent the indicated risk may result in death or serious injury.

Failure to prevent the indicated risk may result in minor injury or property

damage.

Notes related to machine functions but not to safety are marked with the following

indication.

:Note related to product function or protection.

1-1 Magnitudes of risk

1. SAFETY PRECAUTIONS- Be sure to read these instructions to ensure safety -

Instructions to the owner

If you entrust another party to perform installation, operation, relocation, transportation,

maintenanceordiscardingofthemachine,instructtheconcernedpartytoreadandobserve

all the instructions and precautions in this operation manual regarding the particular action

to be taken.

1-2 Denition of the term “technician”

This operation manual is written for arcade personnel. However, the sections marked

“To be conducted by a technician only” in the table of contents are written for technicians.

These tasks should be conducted by technicians only.

Technician:Apersonengagedinmachinedesign,manufacture,inspectionormaintenance

service for a manufacturer of amusement equipment, or a person who has

tecnical knowledge related to electricity, electronics or mechanical engineering

at a level equal to or higher than that of a technical high school graduate and

is engaged routinely in the maintenance and management (including repair)

of amusement machines.

DANGER

CAUTION

WARNING

1-3 Top-priority safety precautions

Should any abnormality occur, turn off the power switch immediately to

stop operating the machine. Then, unplug the power cord plug from the AC

outlet.

Operating the machine without correcting abnormalities can result in a re or

accident.



When adjusting the projector, do not touch any parts other than those

specied in the instructions. Accidentally touching internal parts of the

projector other than those specied can result in electric shock or injury.

* Some internal parts of the projector remain hot or charged with high

voltage even after the power switch is turned off.

Dust accumulated inside the projector can lead to a re or malfunction.

The inside of the projector should be cleaned once a year. Contact your

distributor for internal cleaning of the projector.

Do not dismount the projector screen. Removed screen and internal lens can

converge light and may cause a re, blindness or burns.

Dust accumulated on the power cord plug may cause a re. Check the power

cord plug regularly and remove dust.

Insert the power cord plug rmly into the AC outlet. Poor contact may cause

overheating that can lead to a re or burns.

A damaged power cord can cause a re, electric shock or electrical leakage.

Observe the following cautions.

 Keep the power cord away from heating devices.

Do not twist the power cord.

Do not bend the power cord forcibly.

Do not alter the power cord.

Do not bundle the power cord.

Do not pull the power cord. (Always unplug by holding the power cord

plug, and avoid pulling the power cord.)

Do not place anything on the power cord.

Do not get the power cord caught by the machine, other equipment or

wall.

Do not do anything else that might damage the power cord.

Do not wet the power cord or power cord plug with water. Water can cause an

electric shock or electrical leakage.

Do not touch the power cord plug with a wet hand. Doing so can result in an

electric shock.

The power ratings of the machine are 120 VAC and 6 A. To prevent re and

electric shock, be sure to use interior wiring that conforms to these power

1. SAFETY PRECAUTIONS- Be sure to read these instructions to ensure safety -

WARNING

1. SAFETY PRECAUTIONS- Be sure to read these instructions to ensure safety -

ratings.

Operate the machine with a power supply voltage in the range of 105 to

125 VAC. Operating the machine with a supply voltage outside the specied

range may cause a re or electric shock. To ensure that the machine operates

in optimum condition, maintain the power supply at 120 VAC.



Use consumables and service parts (including fasteners) specied by our

company. To order parts, contact your distributor.

Do not convert the machine without permission. Do not perform any work

that is not described in this operation manual. Unauthorized conversion of

the machine may create unforeseen hazards.

If the ownership of the machine is transferred, be sure to provide this

operation manual and the Projector Adjustment Manual together with the

game machine.

1. SAFETY PRECAUTIONS- Be sure to read these instructions to ensure safety -

1-4 Description of warning labels attached to the machine

The warning labels describe important safety precautions. Observe the

following:

To ensure that the warning labels attached to the machine are easily

legible, install the machine at a proper location with ample illumination

and keep the labels clean at all times. Also, make sure that the labels

are not hidden behind another game machine or other objects.

 Do not remove or alter the warning labels.

 If the warning labels become excessively dirty or damaged, replace them

with new labels. To order warning labels, contact your distributor.

Front side

* Internal parts refer to the AMP PC Board,

switching regulators and others.

(See P. 79 “8-3-1 Projector Tower Assy.”)

Warning sticker Maintenance (B)

Part No.: 461-531

Caution sticker Gun

Part No.:VG40-12401-00

Instruction sticker

Part No. :VG44-07943-00

WARNING

JointAssy

Coin Tower Assy

Rear side of Coin Tower Assy

Warning sticker Maintenance (B)

Part No.: VC40-10599-00

* Internal parts refer to the

transformers and others.

Warning sticker Maintenance

(B)

Part No.: RM44-13905-00

* Internal parts refer to the CPU

Board, USIO PC Board, GUN

DRIVE PC Board, switching

regulators and others.

(See P. 27 “5-3-3 Connecting

the Projector Tower Assy and

Control Assy,” P. 92 “8-3-3 (3)

ReplacingtheCPUBoard,”P.94

“8-3-3 (4) Replacing the USIO

PC Board,” and P. 96 “8-3-3 (5)

Replacing the GUN DRIVE PC

Board.”)

1. SAFETY PRECAUTIONS- Be sure to read these instructions to ensure safety -

Rear side

CONTENTS

INTRODUCTION

1. SAFETY PRECAUTIONS - Be sure to read these instructions to ensure safety - ...................................1

1-1 Magnitudes of risk............................................................................................................................... 1

 1-2Denitionoftheterm"technician" ....................................................................................................... 1

1-3 Top-priority safety precautions............................................................................................................ 2

 1-4Descriptionofwarninglabelsattachedtothemachine...................................................................... 4

CONTENTS............................................................................................................................6

2. SPECIFICATIONS ...........................................................................................................10

3. CHECKING THE PACKAGE CONTENTS........................................................................12

4.OVERALLCONSTRUCTION(NamesofParts)...............................................................14

5. INSTALLATION ................................................................................................................15

5-1 Installation conditions ....................................................................................................................... 15

5-1-1 Locations to avoid ......................................................................................................................................15

  5-1-2Playzoneforinstalledmachine .................................................................................................................16

  5-1-3Preventionofcommunicationinterference..................................................................................................17

 5-2Requireddimensionsofcarry-inpassage(suchasdoorsandcorridors) ...........................................................18

5-2-1Separating the Projector TowerAssy(whenrequiredduetopassageconditions)-Tobeconductedbyatechnicianonly-..........19

 5-3Assembly..........................................................................................................................................22

5-3-1Adjusting the level adjusters .......................................................................................................................22

  5-3-2AssemblingtheSignboardAssy-Tobeconductedbyatechnicianonly-.................................................23

5-3-3 Connecting the Projector TowerAssy and Control Assy- To be conducted by a technician only - ..............................27

5-3-4 Installing the PedalAssys - To be conducted by a technician only -..........................................................29

 5-4Removingandinstallingthefrontdoor -To be conducted by a technician only - ............................. 31

5-5 Inserting the dongle - To be conducted by a technician only -......................................................... 32

5-6 Connecting the power cord and ground lead ................................................................................... 33

  (1)Using3PACsocket...........................................................................................................................................................33

5-7 Optional Dollar BillAdaptor .............................................................................................................. 34

6. MOVING AND TRANSPORTING ....................................................................................35

 6-1Moving(ontheoor) ......................................................................................................................... 35

6-2 Transportation ................................................................................................................................ 36

  6-2-1Manualtransportation(carryingonstairs,etc.)..........................................................................................36

   6-2-2Loadingonorunloadingfromavehicle............................................................................................... 37

6-2-3 Trucking ............................................................................................................................................... 38

7. OPERATION ....................................................................................................................40

7-1 Pre-service check.............................................................................................................................. 40

  7-1-1Safetycheck(beforepowerON).................................................................................................................40