BandLuxe E580 Series Bedienungsanleitung

E580 Series

(Embedded SIM)

Installation Guide

123

Product Overview

DATA

P+DATA

OUT

POWER IN

DATA

P+DATA

OUT

POWER IN

Power: Power LED will remain lit while power is applied.

Signal strength: Indicate receive signal strength.

The Signal Strength LEDs are only used at the

power on to assist the installation.

The CPE will turn off all the Signal Strength LEDs after a

timer expires from power on. Such design is to prevent

the outdoor CPE becoming a potential target particularly

at night. The default time is 60 minutes however,

is user settable in the web GUI.

Mount base: Attach the mounting bracket.

Earth ground terminal: It is necessary to

connect a grounding wire to protect the CPE

from ESD (electrostatic discharges) and lightning.

Ethernet port: Connect to a computer using an

Ethernet cable.

Reset button: Short press to

restart the device. Long press for

for 10 seconds to reset the settings

to the factory default settings.

External SIM card slot: The CPE has

LTE Outdoor CPE Mounting bracket

Passive PoE adapter (E580A series) Passive PoE adapter (E580P series)

Optional: Plug head water

resistant kits (RJ-45)

Package Contents

Sprint embedded SIM inside. Please

insert the external SIM card for special

application.

Install external SIM card

Notice before installation

Step 1: Unscrew the SIM card slot.

Step 2: Insert a valid SIM card into the SIM card

slot. Push it fully until it clicks into place.

Step 3: Screw the cap back on tightly.

Once the external SIM is plug in,

the embedded SIM will no longer be activated.

Choose a solid and safe place (Wall or Pole) for CPE installation

Note:

For optimum reception, there are few things you should consider before

installation. Please see Appendix 2 for important installation considerations.

Prepare two Ethernet cables

Prepare wrenches

Prepare adjustable wrenches or four combination wrenches

(size: 13mm x 2, 8mm x 1, and 19mm x 1)

Be sure that one of the cables used is an outdoor grade CAT 5e (or above)

Ethernet cable type and the length of the cables are adequate to reach the

location of the CPE and indoor PPoE.

Warning:

1. Do NOT start any traffic test (ex: throughput

test and internet browsing) before the

installer returns to the ground.

2. Do ground the CPE to provide protection

from ESD (electrostatic discharges) and lightning.

The CPE has Sprint embedded SIM inside.

For special application that you have to use an

external SIM card, please follow below steps to

load the external SIM card.

- Choose the best location of the house and the

orientation of the CPE to get the strongest signal

reception from base station.

- The ambient temperature for E580 series

must be within:

E580A series : -10°C to 55°C

E580P series : -40°C to 55°C

SIM card

Mount assembly package

A B C D

Kit-1

Quantity: 1

Kit-2

Quantity: 1

Hex Head Bolt

(M8x50mm)

Quantity: 2

M8 Spring Washer

Quantity: 3

M N O P

Kit-4

Quantity: 1

1/2” U Bolt DN63

Quantity: 1

M13 Washer

Quantity: 2

M13 Spring

Washer

Quantity: 2

1/2 Hexagon Nuts

Quantity: 2

E F

Washer M8x22

(OD) mm

Quantity: 2

M8 Hexagon Nuts

Quantity: 2

G H

Hex Head Bolt

(M5x35mm)

Quantity: 2

Spring Washer

(M5)

Quantity: 6

I J K L

Kit-3

Quantity: 1

Washer (M8)

Quantity: 1

Hex. Head Bolt

(M5x20mm)

Quantity: 4

Washer (M5)

Quantity: 4

21.6

18.72

12.7

7.9

13.5

8.9

Wall-mount Assembly

Step 1.

Step 2.

Step 3.

Step 1: Align the mounting bracket on the wall. Using the bracket as

mounting template, mark the positions to drill the holes.

Step 2: Assemble the bracket as shown in the illustration.

Step 3: Attach the bracket to the back of the CPE.

Step 4: Hang the CPE to the wall and secure the bracket using the designated

screws and washers.

Pole-mount Assembly

Step 3.

Step 1.

Step 2.

Step 1: Align the mounting bracket on the wall. Using the bracket as

mounting template, mark the positions to drill the holes.

Step 2: Assemble the bracket as shown in the illustration.

Step 3: Attach the bracket to the back of the CPE.

Insert the Ethernet cable

For 1.5” to 2” diameter

Step 4.

For 2.5” diameter

Step 4.

Unscrew the Ethernet port and insert one

end of the Ethernet cable into the CPE port.

Note:

For best protection against dust and water,

ethernet cable MUST be fitted with a water-proof

RJ-45 jack. Please see Appendix 1 for water-proof RJ-45

cable jack assembly.

Step 4: Align a pole on the bracket and assemble the pole bracket as shown.

Step 5: Adjust the CPE position to an appropriate direction and secure the pole

bracket using the designated screws and washers.

Connect to PC

Prepare two Ethernet cables for connection.

Step 1: Insert the other end of the Ethernet cable to “P+D OUT” port of the

PoE adapter.

Step 2: Connect another Ethernet cable to a Network Hub/Router or directly

to PC/Laptop via PoE adapter (“Data/IN” port).

Step 3: Plug the PoE adapter to an electrical outlet.

Using Passive PoE adapter (E580A series)

Using Passive PoE adapter (E580P series)

LTE Outdoor CPE

PoE

PC/Laptop

Network Hub/Router

Data/IN

P+D/OUT

Step 2

Step 1

DATA

P+DATA

OUT

POWER IN

Electrical outlet

Step 3

LTE Outdoor CPE

Adapter

PC/Laptop

Network Hub/Router

Data/IN

P+D/OUT

Step 2

Step 3

Step 1

DATA

P+DATA

OUT

POWER IN

PoE

Electrical outlet

Adjusting CPE position

For optimum reception, fine tune the CPE orientation (horizontally or

vertically) to have the best signal strength shown from LED or other test

equipment.

Note: LEDs (on the front panel) indicate signal strength.

Horizontal angle adjustment

Step 1: Loose the top knob using the wrench as

shown.

Step 2: Swivel the device to the left or right

to face the direction of the base

station.

Step 3: Secure the knob using

the wrench after the

position is fixed.

Vertical angle adjustment

Step 1: Loose the side knob using the wrench as

shown.

Step 2: Adjust the device position up or down

to face the direction of the base

station.

Step 3: Secure the knob using the wrench

after the position is fixed.

Note

If you can NOT connect to the network, please follow below steps to set

APN manually.

1. Go to

Network > Mobile Internet > WWAN Setting- APN Profile Setting

to enter the APN profile name, then click Add.

2. Enter APN, User Name, and Password, then click Save.

3. Go to Network > Mobile Internet > WWAN Setting- Network Setting

to configure the APN to Manual. Then select the Profile Name you

added from the Profile Selection, then click Apply.

Above change will be applied after the system is rebooted.

Once the external SIM is reinserted, you must restart the CPE to read the

SIM card properly.

For more detail information, please go to

http://www.bandrich.com/UM/E580_Embedded_Series.pdf

to download User Manual.

Using web management

Step 1: Enter the IP address (http://192.168.1.1) of the CPE in your

browser’s address bar then press Enter.

Step 2: On the opening screen, enter the username (admin) and password

(admin).

Step 3: Click OK to login to the main screen.

Step 4: Click one of the header tabs for advanced features.

E580 series CPE uses network domain 192.168.1. X.

For any downstream connections, all devices should avoid using this

network domain otherwise there might be IP address conflict and cause

communication failure.

If the PIN verification on your SIM card is enabled, please go to

Network > Mobile Internet > UICC/SIM PIN Management to unlock the

PIN code.

Inhaltsverzeichnis

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung