BandRich BandLuxe M250 Bedienungsanleitung
BandLuxeTM
M250 Series HSUPA Module
User Manual
Class: User Manual
Doc. No.: M250-D-001
Doc. Version: 1.0
Publish Date: 2008-Dec-05
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUALARE SUBJECT
TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS
MANUALARE BELIEVED TO BEACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY
PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET
FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCTAND ARE INCORPORATED
HEREIN BY THIS REFERENCE.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF
THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. PRODUCT AND THE ABOVE-NAMED
SUPPLIERS DISCLAIM ALLWARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION,
THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR
ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL PRODUCT OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR
LOSS OR DAMAGE TO DATAARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF
PRODUCT OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
BandRich M250
Datasheet
Document Number: M250-D-001
BandRich Inc.
7F., No. 188, Baociao Rd., Sindian City
TAIPEI, TAIWAN, R.O.C.
http://www.bandrich.com
COPYRIGHT ©2007-2008 BandRich All rights reserved.
Table of Contents
Section 1 Introduction..........................................................................1-2
Section 2 Device Driver Interface........................................................2-2
Section 3 AT Command Set Reference...............................................3-2
Section 4 Packing Information.............................................................3-2
Section 5 FCC Statement......................................................................5-1
Section 1 Introduction
1.1 General Description
The M250 module series is PCI Express Mini Card providing WWAN (HSUPA, HSDPA, WCDMA,
EGPRS, and GPS) connectivity to laptops or any other device equipped with a PCI Express Mini Card
slot.
Figure 1-1 Top View
Figure 1-2 Bottom View
1.2 Features
1.2.1 WCDMA
yFDD 850/1900/2100 MHz
yPower Class 3 (+24dBm)
yWCDMA 384/384 kbps downlink/uplink modem operation
yHSUPA 2Mbps uplink modem operation (SW upgradable to 5.7Mbps)
yHSDPA 7.2Mbps downlink modem operation
ySupports UL and DL Compressed Modes
ySupports Circuit and Packet-Switched Data
yM250V supports 3G voice call via PCM interface
1.2.2 E-GPRS
y850/900/1800/1900 MHz
yGSM Power Class 4 (2W) for 850/900 bands
yGSM Power Class 1 (1W) for 1800/1900 bands
yEDGE class E2 (+27 dBm in 850/900 bands, +26 dBm in 1800/1900 bands)
yGPRS/EGPRS Multislot Class 12 (4 slots Rx, 4 slots Tx, 5 slots active max)
yGPRS/EGPRS Class B Type 1 MT
yGPRS CS1-CS4; EGPRS MCS1-MCS9
yCircuit Switched Data: 14.4 and 9.6 kbps
yM250V supports GSM voice call via PCM interface
1.2.3 GPS
yHigh-sensitivity GPS that integrated in Qualcomm gpsOne solution.
yHigh availability that is enabled by using both satellite and network information.
yThe GPS RF path is shared with the UMTS Receive Diversity RF path. When the GPS
functionality is enabled, the UMTS Receive Diversity will be disabled.
1.2.4 Baseband Functionality
The M250 module interfaces with host device through PCI Express Mini Card interface. The
interface equips with USB2.0 interface, USIM interface, LED control signal, Wake# signal to request
host device return from sleep/suspended state, and W_Disable# signal to disable radio operation.
There are several GPIO pins (2.6V compatible) reserved for customized applications, please contact
BandRich for discussion. Besides the above mentioned interfaces, M250V also provides PCM
interfaces reserved for voice applications. The M250-LC features low power consumption but
requires higher input voltage than PCI standard.
1.2.5 Software Functionality
M250 module series is supplied with device driver of Microsoft Windows Vista 32/64, Windows XP
SP2 above, Windows 2000 SP4 above, Mac OSX 10.4 above, and Linux Fedora 8, Unbuntu 7, Open
SuSE 10.
1.3 M250 PCI-Express Mini Card Interface
1.3.1 Pin Description
Table 1-1 M250 Module Series Connector Pin-out
Pin No. Name Pin No. Name
1 WAKE#/GPIO1 (optional) 2 Vaux
3 PCM_DOUT (M250V only) 4 GND
5 PCM_DIN (M250V only) 6 N.C./GPIO2 (optional)
7 N.C. 8 UIM_PWR
9 GND 10 UIM_DATA
11 PCM_SYNC (M250V only) 12 UIM_CLK
13 PCM_CLK (M250V only) 14 UIM_RESET
15 GND 16 N.C.
17 N.C. 18 GND
19 N.C. 20 W_DISABLE#
21 GND 22 HW_RST#
23 N.C./GPIO3 (optional) 24 Vaux
25 N.C. 26 GND
27 GND 28 N.C.
29 GND 30 N.C.
31 N.C. 32 N.C.
33 N.C. 34 GND
35 GND 36 USB_D-
37 GND 38 USB_D+
39 Vaux 40 GND
41 Vaux 42 LED_WWAN# *
43 GND 44 N.C.
45 N.C. 46 N. C.
47 N.C. 48 N.C.
49 N.C. 50 GND
51 N.C. 52 Vaux
For more information, please refer to PCI-SIG, PCI Express Mini Card Electromechanical
Specification 1.2. http://www.pcisig.com/home
Figure 1-3 Pin-out information of M250 series (Top View)
1.4 Network LED indicate device
The Network LED indicated device is ground-referenced current sink. The host drives the device to
provide a current path and an appropriate voltage for LED at PIN 42 of M250 module. Figure 2-2
shows the block diagram of the current drivers. Table 2-3 describes the LED output characteristics in
different states.
Figure 1-4 LED Current Driver Example
Current Control
M250 Module
VDD
PIN42
Table 1-2 LED Output
LED State Module Status Description LED Characteristics
OFF Module is not powered. LED is OFF.
ON Module is powered and camped on
network, but not transmitting or receiving. LED is continuously ON.
Slow blink Module is powered and searching for
network (not yet registered on network).
LED is flashing at a steady slow
speed.
250ms±5% ON period and
750ms±5% OFF period
LED State Module Status Description LED Characteristics
Intermittent
blink Module is transmitting or receiving
LED is flashing intermittently
during data transfer activity.
50ms±5% ON period and
250ms±5% OFF period
USB Interface
M250, M250V and M250-LC module are compliant with USB2.0 in all three modes (Low speed, Full
speed, and high speed). When two devices are connected via a USB interface, one of the devices must
act as a host, and the other device must act as a peripheral. The host is responsible for initiating and
controlling traffic on the bus. For example, the USB specification requires PCs to act as hosts, and
other devices such as M250 to act as devices.
Figure 1-5 USB Interface
1.5 USIM Interface
The universal subscriber identification module (USIM) is a smart card for UMTS/GSM cellular
applications. The USIM provides the required subscription information to allow the mobile equipment
to attach to a GSM or UMTS network. The USIM also provides the subscriber's verification
procedures as well as authentication methods for network authentication during the network
registration procedures. Upon power-up or after a soft-reset, the clock and data lines to the USIM will
be active through the initialization process. Figure 2-3 shows the SIM card pin definition. It’s
recommended to implement hardware USIM detection mechanism or complete avoiding USIM
hot-plug through mechanical design. The reference design for hardware USIM detection is provided
in the “Application Note for BandLuxe Module USIM Detection Recommendation”.
Table 1-3 SIM Card Pin Definition
Pin No. Description
1 Vcc
2 RST
3 CLK
4 GND
5 Vpp
6 I/O
Inhaltsverzeichnis
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
