Baolong TMSS6D4 Bedienungsanleitung

OPERATION MANUAL OF TPMS SENSOR

MODEL: TMSS6D4

Thank you for choosing our TPMS. This guide instructs the technician how to properly

mount and dismount a Baolong Huf TPMS snap-in sensor.

Introduction of TMSS6D4

TMSS6D4 is the transmitting module in TPMS. Its working frequency is 433.92MHz;

Receiver Low frequency ：125KHz; supply:Battery;Radio frequency uses the FSK

modulation and Machester encoding mode;Antenna type:Monopole antenna,antenna

Gain:-3.7dB~-3.4dB;cable loss：3.12dB.The communication mode between WARDKS and

receiving module is RF wireless communication. The module detects pressure and

temperature inner the tire periodically and sends these information via RF output circuit to

the receiving module. One can manually detect data inner tire by LF wake-up tools. Install it

on the rim together with cycle valve.

PART ONE MOUNTING AND DISMOUNTING OF TRANSMITTER

1. Mounting of Transmitter

1.1 Identify Transmitter

Check whether the prepared sensor is the same with the image below.

Note: Only plastic or aluminum caps, aluminum valves and nickel plated valve cores can be

used when replaced.

①Self-lock Screw

②Electronal Module

1.2 Before the transmitter is installed, the rim around

the hole must be cleaned with a cloth.

1.3 Remove the Self-lock Screw①, insert the valve stem

through the rim hole from inside.

1.4 Place the Self-lock Screw①on the valve stem, and

tighten with 5 Nm (44 inch pounds) torque.

1.5 Lock the rim on the tyre changer. (If the mounting

head of the tyre changer is positioned at 12 o’clock,

then the valve should be at the 7 o’clock position.)

Apply lubricant on both the tyre bead and rim. Mount

the lower tyre bead on the rim. Ensure that the tyre

bead does not touch the electronic module during

mounting.

1.6 Mount the upper tyre bead the same way. (If the

mounting head of the tyre changer is positioned at 12

o’clock, then the valve should be at the 5 o’clock

position.) Inflate the tyre to nominal pressure.

1.7 Apply soapsuds on the valve tip. If no leakage is

found, put on the valve cap○

6. If unsuccessful, try again.

Inside the tyre

Outside the tyre

1.8 Dynamically balance the wheel before it is placed

back on the vehicle.

2. Dismounting of Transmitter

2.1 Deflate the tyre and remove the wheel weights

from the rim. Push the tyre bead away from the rim.

Make sure to always set the bead breaker at least 90

degrees from the valve stem to avoid damaging the

electronic module.

2.2 Firmly fix the wheel on the turntable clamps. (If the

mounting head of the tyre changer is positioned at 12

o’clock, then the valves stem should be at the 11

o’clock position.) Apply lubricant to both tyre bead and

rim, and then remove the upper tyre bead.

2.3 Use the same procedure to dismount the lower

tyre bead. (If the mounting head of the tyre changer is

at the 12 o’clock position, then the valves stem should

also be at the 12 o’clock position.)

2.4 Final inspection: Visually inspect the rim, valve stem and electronic module to ensure

no damage has occurred.

PART TWO FCC’s Authentication Announcements

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy, and if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

–Consult the dealer or an experienced radio/TV technician for help.

PART THREE IC’s Authentication Announcements

CAN ICES-3(B)/NMB-3(B)

PART FOUR WARRANTY

This warranty covers substantial manufacturer’s defects in workmanship and materials. It

does not cover any unit that is damaged beyond normal use, not properly installed, subject

to chemical contact, or other acts not sanctioned by the Owner’s Manual.

All components are covered for one year following the date of purchase. If the warranty

period specified in local law exceeds the period provided by Baolong Huf, the former will

supersede the latter.

The warranty will be honored by any authorized Baolong Huf dealer. The owner is required

to provide date of proof of purchase. The authorized dealer will determine if there is a

warranty condition associated with materials and/or manufacturing workmanship. If a

warranty condition exists, the component will be replaced free of charge and shipping

prepaid. The owner is responsible for any labor and installation charges.

The warranty does not include any further obligation whatsoever, including but not limited to

actual installation of the replacement unit on the customer’s vehicle.

All other Warranties, expressed or implied, are disclaimed. All collateral agreements, which

purport to modify this limited warranty, are of no effect. The absolute limit of liability is the

purchase price of the unit.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with

"CE" and comply therefore with the applicable harmonized European standards

listed under the RED Directive 2014/53/EU, the RoHS Directive 2011/65/EU.

EU Conformity Statement

This product is marked with "CE" and comply therefore with the applicable harmonized

European standards listed under the Radio Equipment Directive 2014/53/EU.

RF Exposure Information

This device has been tested and meets applicable limits for Radio Frequency (RF) exposure.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be

disposed of as unsorted municipal waste in the European Union. For

proper recycling, return this product to your local supplier upon the

purchase of equivalent new equipment, or dispose of it at designated

collection points. For more information see:www.recyclethis.info.

Please take attention that changes or modification not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of the device.

IC Statement

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Baolong Huf Shanghai Electronics Co.,Ltd. is not liable for any direct, consequential,

indirect or punitive damages of any kind.

Hereby, Baolong Huf Shanghai Electronics Co., Ltd. declares that the radio equipment type

TMSS6D4 is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

https://www.intellisens.com/downloads

Frequency band: 433.92 MHz

Maximum Transmit Power: < 10 mW

Manufacturer:

Baolong Huf Shanghai Electronics Co., Ltd., 1st Floor, Building 5, 5500 Shenzhuan Rd,

Songjiang Shanghai, China

Importer：

Huf Baolong Electronics Bretten GmbH

Gewerbestraße 40

D-75015 Bretten

NOTE:Baolong Huf Shanghai Electronics Co.,Ltd. reserves the right to change the contents of this

manual at any time without notice. The information contained in this manual is proprietary and must not

be reproduced without prior written consent from Baolong Huf Shanghai Electronics Co.,Ltd.

Company:Baolong Huf Shanghai Electronics Co.,Ltd.

Address:1st Floor,Building 5,5500 Shenzhuan Rd,Songjiang,Shanghai

TEL:+86-21-31273333

Fax:+86-21-31190319

E-mail:sbic@baolong.biz

Web:www.baolong.biz

Inhaltsverzeichnis

Andere Baolong Sicherheitssensor Handbücher

Baolong

Baolong TMSS6A4 Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung