Barco AP20 Bedienungsanleitung

AP20 & AP24 Fan Replacement Kit

Installation Manual

R59770891/00

28/09/2015

Barco NV

President Kennedypark 35, 8500 Kortrijk, Belgium

Phone: +32 56.36.82.11

Fax: +32 56.36.883.86

Support: www.barco.com/en/support

Visit us at the web: www.barco.com

Printed in Belgium

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-

ranties or merchantability and ﬁtness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the

program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this

publication; these changes are incorporated in new editions of this publication.

The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site

https://www.barco.com/en/signin.

stored in a retrieval system without the prior written consent of Barco.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.

All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for

the products or their manufacturers.

1. Fan replacement kit

1. FAN REPLACEMENT KIT

Overview

• Kit content

• Installation process overview

• Remove the top cover

• Remove the front panel assembly

• Remove the power supply assembly

• Replace the fan assembly

• install the power supply assembly

• Install the front panel assembly

• Install the top cover

WARNING:This manual is only intended for qualiﬁed service personnel.

1.1 Kit content

What’s in the box?

This kit contains the following:

• 1 fan subassembly

• 4 Keps nuts, 6–32, steel, clear zinc ﬁnish

• 4 screws, 6–32 x 1/2” ﬂat-head Phillips, 100 degree, steel, clear zinc

Purpose of the spare part kit

The fan subassembly in the fan replacement kit is designed to replace the fan of the AP20 and AP24 audio processor. This document

describes in detail the replacement procedures.

1.2 Installation process overview

About this chapter

This chapter gives an overview of the different stages in the installation process. The stages displayed in bold are described in more

detail in this manual. More information about the other stages can be found in the service manual of the audio processor.

Safety warnings

WARNING:Servicingmustbedonebyauthorizedandqualiﬁed technical personnel only, which are thor-

oughly familiar with the product and all of the proper safety checks of this product.

CAUTION:The AP20 and AP24 audio processors contain parts that are static sensitive. Use caution when

handling to avoid damage and avoid touching circuit boards.

When removing or installing internal cables, keeping one hand on the chassis will help to ground you with

respect to internal circuitry.

It is a good idea to stand on a linoleum or cement ﬂoor (not carpet) when handling the processor.

Installation from A to Z

1. Find a suitable workspace to perform the procedure. Antistatic foam or an antistatic mat is an ideal work surface.

2. Turn off the processor’s rear panel power switch and unplug the power cord.

3. Remove the top cover. See "Remove the top cover", page 2

R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015 1

1. Fan replacement kit

4. Remove the front panel assembly. See "Remove the front panel assembly", page 2

5. Remove the power supply assembly. See "Remove the power supply assembly", page 4

6. Replace the fan assembly. See "Replace the fan assembly", page 4

7. Install the power supply assembly. See "install the power supply assembly", page 6

8. Install the front panel assembly. See "Install the front panel assembly", page 6

9. Install the top cover. See "Install the top cover", page 7

10.Connect the audio processor to the AC power and turn it on.

11.Verify if the new fan is working correctly.

1.3 Remove the top cover

Necessary tools

#2 Phillips screwdriver

How to remove the top cover from the audio processor?

1. Remove the two 4–40 x 1/4” pan head Phillips screws from both sides of the top cover.

Image 1-1

2. Slide the top cover to the back of the processor.

Image 1-2

3. Lift the top cover up to remove it.

1.4 Remove the front panel assembly

Necessary tools

#1 Phillips screwdriver

How to remove the front panel assembly?

1. Carefully turn the processor on its side.

2. Remove four 4–40 x 3/16” ﬂat-head Phillips screws from the bottom.

2R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015

1. Fan replacement kit

Image 1-3

3. Place the processor back down with the top facing upwards.

4. Gently remove the ribbon cable connector from the front panel.

Image 1-4

Tip: Pull evenly on both sides and be careful not to bend pins or damage the ribbon cable connector.

Do not tug on the wires to remove the connector, as this ma damage the cable.

5. Remove four 4–40 x 3/16” ﬂat-head Phillips screws on both sides of the processor (eight in total).

Image 1-5

Note: Be careful when removing the last screws.

6. Fold the front panel down and away, to provide more room to access to the fan.

Note: be careful not to stress any of the cables that are still attached.

R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015 3

1. Fan replacement kit

1.5 Remove the power supply assembly

Necessary tools

#1 Phillips screwdriver

How to remove the power supply assembly?

1. Remove three of the four 6–32 x 1/4” pan-head Phillips screws that hold the power supply in place; These screws can be found

on the side.

Image 1-6

2. Remove the fourth screw, while holding the power supply. Do this so that the power supply will not fall.

3. Carefully lift the power supply out and set it on top of the card cage.

Tip: No cables need to be removed from the power supply, but make sure not to stress the cables.

Image 1-7

1.6 Replace the fan assembly

Necessary tools

• A small ﬂat-blade screwdriver

• #2 Phillips screwdriver

• 5/16” combination wrench

Necessary parts

• Sub-Assembly, Fan

• Keps nuts, 6–32, steel, clear zinc ﬁnish (4 pieces)

• Screw, 6–32 x 1/2” ﬂat head Phillips, 100°, steel, clear zinc (4 pieces)

How to replace the fan assembly?

1. Remove the fan power connector from the front panel.

Tip: Useasmallﬂat-blade screwdriver to help lift up the connector out of the socket.

Caution: Do not pull the power connector directly up on the wires. This will pull them out of the connector.

4R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015

1. Fan replacement kit

Image 1-8

2. Remove four 6–32 x 1/2” ﬂat-head Phillips screws and four 6–32 Keps nuts holding the fan to the chassis.

Image 1-9

3. Remove the fan assembly.

4. Install the new fan assembly, using four 6–32 x 1/2” ﬂat-head Phillips screws and four 6–32 Keps nuts.

Note: New screws and nuts for this are included in the kit, as existing hardware may be covered in old Loctite.

Make sure that the wires and arrows indicating air ﬂow direction are in the correct orientation.

Image 1-10

5. Connect the fan power cable to the front panel board socket CN1. The connector is keyed to go into the socket in only one

direction.

R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015 5

1. Fan replacement kit

Image 1-11

1.7 install the power supply assembly

Necessary tools

#1 Phillips screwdriver

Necessary parts

Four 6–32 x 1/4” pan-head Phillips screws

How to install the power supply assembly?

1. Move the power supply back into place, taking care of the cabling.

2. Install the power supply, using four 6–32 x 1/4” pan-head Phillips screws.

Image 1-12

1.8 Install the front panel assembly

Necessary tools

#1 Phillips screwdriver

Necessary parts

eight 4–40 x 3/16” ﬂat-head Phillips screws

How to install the front panel assembly?

1. Slide the front panel back into the chassis.

2. Insert four 4–40 x 3/16” ﬂat-head Phillips screws on each side to secure.

6R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Barco Computerhardware Handbücher

Barco

Barco Iosono Core R9801500 Bedienungsanleitung

Barco

Barco DCPB-2160 Bedienungsanleitung

Barco

Barco ImagePRO-HD Bedienungsanleitung

Barco

Barco LED-PRO Bedienungsanleitung

Barco

Barco BlendPRO-II Bedienungsanleitung

Barco

Barco S3 series Bedienungsanleitung

Barco

Barco ACSAR Bedienungsanleitung

Barco

Barco EX Installations- und Betriebsanleitung

Barco

Barco ImagePRO-3G Bedienungsanleitung

Barco

Barco ImagePRO-II Bedienungsanleitung

Barco

Barco ICP-D Bedienungsanleitung

Barco

Barco DCPB-2120 Bedienungsanleitung

Barco

Barco DCPB-2100 Bedienungsanleitung

Barco

Barco iCon H250 Bedienungsanleitung

Barco

Barco DCPB-2140 Bedienungsanleitung

Barco

Barco TransForm SCN Bedienungsanleitung

Barco

Barco S3-4K Bedienungsanleitung

Barco

Barco ImagePRO-II Bedienungsanleitung

Barco

Barco Encore VPx Bedienungsanleitung

Barco

Barco IOSONO ONE Series Bedienungsanleitung

Barco

Barco iCon H600 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung