Barco DP2K Series Bedienungsanleitung

Projector Components

B Series

C Series

— Used for controlling, set-up and projector maintenance (e.g., resetting the lamp

run-time when a new lamp is installed).

— Provides power and communication for the Touch Panel.

: To avoid connector damage, align the pins before you connect the cable.

— Removes heat from lamp house. Must be connected to external extraction system.

: The extraction system must be running. A flexible duct must be installed.

— Automatically adjusts the image between screen formats when a

macro is selected. Always remove the lens cap prior to use.

— Used for communication, GPIO, and alternative content connections to the projector.

— Used to switch lamp and dowser on or off. Also used for macro selection, lens

adjustments and selection of test patterns.

— Powers the projector head off, but the LPS units remain on.

: . Voltage is still present in the B series LPS when the Mains Switch is off.

—= System OK

= Error condition

= Warning

= Maintenance notification

Input CoverLamp Cover Front Cover

Left Side Cover Rear Cover

Front CoverRear CoverInput CoverLamp Cover

— Powers projector on and off. Shuts off all electrical connections.

: For all projectors, the lamp must be cooled down for 10 minutes before switching off.

High voltage and strong UV

radiation is present in these

projectors!

To prevent personal injury, electrical shock,

exposure to UV radiation and fire hazard,

always refer to the “Safety” chapter in any

DP2K Installation Manual.

Quick Start Guide — Operators

Left Side Cover

QSG_DP2K_Operator_EN_110208

Quick Start Guide — Operators

Projector Features

Used to configure the projector for each show. Each

button is linked to a list of commands (called a

“Macro”) as defined in the Communicator software.

Press once to turn the lamp on.

Press once to turn the lamp off.

= Green = Red Press to enable and cycle through

4 test patterns. To return to

normal operations, press a fifth

time, or select a macro. Note that

the button turns green when boot-

up is complete.

Positions the image on screen.

Used for manual override.

Increases or decreases image size.

Adjusts primary image focus.

This security feature must be used

if the projector’s light engine

compartment is opened, or if any

boards are removed.

Keypad

Input Module

These features are not

typically used for normal

operations. The video

server sends commands to

the projector to control

these functions.

HD-SDI Module

Press once to open the dowser.

Press once to close the dowser.

= Green = Red

Accepts an encrypted content data stream

from the server. LEDs indicate sync status,

and if the input is selected.

Accepts data signals from alternative

content devices. LEDs indicate sync

status, and if input is selected.

Used for communication from projector to server and

theater management system. Also used for laptop

connection, for upgrades and running Communicator.

Quick Start Guide — Operators

General Procedures

Ensure that the extraction system is on, and the flexible

duct is installed.

If the projector’s turns red, yellow or blue,

refer to the section in this guide.

Power Up

Switch on the . Allow up to one minute for

the projector to finish the boot-up sequence. Boot-up is

complete when the button turns green.

Remove the lens cap (if applicable).

If the lamp is on, press the button and allow

the lamp to cool for 10 minutes prior to electrical

power down.

After the 10 minute cool down period, switch off the

projector’s .

Damage will result if you do not

allow the lamp to cool down!

Power Down

System Reboot Sequence

Switch off the .

If the lamp is on, press the button and allow the

lamp to cool for 1 minute.

Continue with normal projector operations as required.

After 30 seconds, turn on, and allow 1 minute

for the system to boot, until button turns green.

Play the movie from the server.

Check if the button turns green.

Check the image on screen for proper alignment

and color.

: If the image is not aligned with the screen

masking, use the to correct the

image on screen. Be sure to notify the theater technician.

During normal operations, the server should start the projector automatically.

If it does not start automatically, use the following steps.

Select the appropriate for the next show.

Allow a moment for the lens to move into position,

and the electronic “masking” files to be loaded.

Play the movie from the server.

Check the image on screen for the proper alignment

and color.

Press the button. Check if the button

turns green.

Press the button if required.

Playing a Movie Controlled by the Server

Playing a Movie Manually

Check that the appropriate is selected.

: If the image is not aligned with the screen

masking, use the to correct the

image on screen. Be sure to notify the theater technician.

Quick Start Guide — Operators

Maintenance Procedures

Turn the projector off.

Remove the projector’s front and left side covers.

Cleaning the Intakes and Filters

Vacuum clean all air intakes, and vacuum clean the

LPS main air intake on the bottom of the projector.

Slide the out. Use a vacuum

cleaner, or clean gently with water (see note below).

Re-install the filter when complete.

Slide the out. Use a vacuum cleaner,

or clean gently with water (see note below).

Re-install the filter when complete.

Slide the out.

Location on C Series. Location on B Series.

Use a vacuum cleaner, or clean gently with water (see

note below). Re-install the filter when complete.

Re-install all covers, and turn the projector back on.

Optical System Maintenance

When needed, clean the with a damp lens cloth,

using distilled water. Do not use tap water or alcohol.

When needed, clean the .

Replace the lamp when the maximum lamp runtime is

reached and the turns blue, or when the

projector’s light output falls below optimum requirements.

For full details on all maintenance activities, refer to the .

Cleaning the Exterior of the Projector

Switch off the projector, and unplug the projector from

the mains power net.

Clean the projector’s outside housing with a damp cloth.

Stubborn stains may be removed with a cloth that is

lightly dampened with a mild detergent solution.

Checking the Cooling Liquid Level

Remove the side cover on the light processor side of the projector.

All Series 2 projectors (except the DP2K-12C) are liquid cooled. It is important to check the liquid level

every 3 months. In the reservoir, the liquid level must be between the and labels. A significant

drop in level indicates a major leak in the cooling system, which will require immediate attention.

Look through the small window in the security cover, and check the liquid level in the reservoir.

If the level is between and , no action is needed.

If the level is lower than , contact the theater’s technician immediately. He will need

to start the refill procedure and check for leaks in the cooling system.

: If you cannot see the fluid level, remove the projector’s top

cover and shine a flashlight on the reservoir filler cap while looking

through the small window.

46a

If water is used, ensure that the filter

is dry before re-installing.

Quick Start Guide — Operators

Troubleshooting

Problem: The lamp does not strike

Press the button. Between each strike

attempt, allow 10 seconds (if lamp is cold) or

1 minute (if lamp is hot).

If after the third attempt the lamp does not

strike, check the for errors, then

contact the theater’s technician.

Reselect the proper on the

projector for the current movie.

Use the to select color bars.

Check that red, green and blue can all be seen.

Reselect the proper again, for the

current movie.

Restart the projector and server, and try to re-

play the movie. Let the lamp cool down for at

least 1 minute prior to restarting.

Problem: Content is distorted or not playing with the correct color

1 3

= Error condition. Restart the projector.

If the status light turns green, problem is

resolved. Check the for “red”

marked error messages. If you find an

error, report it to the theater technician.

= Warning. Check the

for “yellow” marked warning messages

and take action accordingly.

= Maintenance notification. Check the

for “blue” marked messages

and perform the suggested maintenance.

Problem: The projector Status Light is solid red, yellow or blue

Verify that the correct is selected.

Check to see if the is on and the

is open.

Verify that the server is playing.

Verify the operation of the projector with a

Check all video connections from the

server. Try playing different content.

Check that the is removed.

Restart projector and server. Try to play the

movie again. Let the projector lamp cool down

for at least one minute prior to restarting.

Problem: There is no image on the screen

1 53

On the Touch Panel, select the and press

the " " button.

Check the “ ” reading. If the

light output does not indicate at least 11 FL, contact

the theater technician

Problem: The image appears dim

Check that the extraction system is operating.

Check that the filters are clean.

Check the booth’s ambient temperature,

which must fall between:

• 50 - 95 degrees Fahrenheit

• 10 – 35 degrees Celsius

Contact the theater technician.

Problem: The projector indicates an overheating error

Andere Handbücher für DP2K Series

Inhaltsverzeichnis

Andere Barco Projektor Handbücher

Barco

Barco R9002129 Bedienungsanleitung

Barco

Barco CNWU-61B Bedienungsanleitung

Barco

Barco Galaxy 9 HC+ Betriebsanleitung

Barco

Barco R9002372 Bedienungsanleitung

Barco

Barco R9002180 Bedienungsanleitung

Barco

Barco DP2K-11CX Betriebsanleitung

Barco

Barco R7628162K Bedienungsanleitung

Barco

Barco Galaxy 4K23 Bedienungsanleitung

Barco

Barco SERIAL COMMUNICATION LCD PROJECTOR Bedienungsanleitung

Barco

Barco LX-5 SERIES Bedienungsanleitung

Barco

Barco CLM W6 Bedienungsanleitung

Barco

Barco Vision 708 Bedienungsanleitung

Barco

Barco Athena Bedienungsanleitung

Barco

Barco iQ Pro G300 Montageanleitung

Barco

Barco BarcoGraphics Maxwell/ 6300 Bedienungsanleitung

Barco

Barco BARCOREALITY SIM 6 MK II + WARP 6 Bedienungsanleitung

Barco

Barco R9000893 Bedienungsanleitung

Barco

Barco UDX Series Bedienungsanleitung

Barco

Barco RLM R6+ Performer R9010270 Bedienungsanleitung

Barco

Barco Bragi Bedienungsanleitung

Barco

Barco FLM HD18 Bedienungsanleitung

Barco

Barco Njord Bedienungsanleitung

Barco

Barco F70 Series Bedienungsanleitung

Barco

Barco Galaxy 6 Classic+ Handbuch

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung