Bard 8620-343 Betriebsanleitung

Page 1 of 9

Bard Manufacturing Company, Inc.

Bryan, Ohio 43506

www.bardhvac.com

Manual: 7960-918

Supersedes: NEW

Date: 6-23-21

UV-C exposure can cause burns to skin and

damage eyes.

Ensure proper safety precautions are taken

during installation.

A trained, experienced technician must

install the UV-C eld kit.

!WARNI NG

UV radiation hazard.

Use only with shielding in place.

Protect eyes and skin from

exposure to UV light.

!CAUTI ON

Ultraviolet band C (UV-C) energy may cause

damage to non-metallic components except

for UV-rated and HVAC-style drain pans.

Select mounting locations that prevent

exposure to vulnerable components. If

mounting locations are limited, protect

components with UV-resistant material

such as aluminum foil, aluminum duct tape,

metallic shields, etc.

!CAUTI ON

8620-343 & 8620-344

Wall Mount UV-C LED Field Kits

SUPPLEMENTAL INSTRUCTIONS

Exposed moving parts.

Disconnect all electrical power before

servicing.

Failure to do so can result in severe injury

or amputation.

!WARNI NG

Electrical shock hazard.

Disconnect the remote electric power

supply or supplies before servicing.

Failure to do so can result in serious injury

or death.

!WARNI NG

Sharp metallic edges.

Take care and wear appropriate protective

devices to avoid accidental contact with

sharp edges.

Failure to do so can result in personal injury.

!CAUTI ON

Manual 7960-918

Page 2 of 9

Personal Protective Equipment (PPE)

UV radiation is absorbed by clothing, plastic or glass.

Once absorbed, the UV radiation is no longer active.

Wear UV goggles or face shield. Cover any exposed skin

with coats, gloves, etc.

UV-C band light spectrum is not visible to the eye.

NOTE: The health aspects associated with the use of

this product and its ability to aid in disinfection

of environmental air have not been investigated

by UL.

NOTE: Color shift or chalking may occur without

affecting structural properties.

Product Specifications

Model

Olympia UV-C Light F15T5-15W-UVC-DL

Electrical Specs

Input Voltage 120-277VAC

Power Consumption 15W

Frequency 50/60Hz

Dimensional Specs

Unit Dimensions 15-1/8" L x 3/4" H x 1" D

Weight 1 lb

Performance

Irradiance 170µW/cm2

UL Listing and Certications

Compliance and

Certications

UL 1598

CSA C22.2#250.0

UL 8750

UL 2043

RoHS Directive

“UV-C LED Light Bar Installed” Label 7961-622-0375

is located near unit serial plate

Kit Voltage Wall-Mount Models

8620-343 460V W**A2,W**AA, W**AB

W**L2, W**LA, W**LB

W**H2, W**HA, W**HB

W*SAC, W*RV, W*LV

8620-344 230V

MIS-4309

MAGNETIC CLIPS

3/4"

151

10"

(REF)

Dimensions

Overview

The UV-C eld-installed light kits utilize UV-C LED

lighting technology to sterilize and improve overall air

quality within an occupied space. UV-C exposure is

proven to damage the DNA of microorganisms and render

them inactive aiding in preventing the spread of diseases.

These instructions are applicable to the following models:

Manual 7960-918

Page 3 of 9

Parts List

WARNING LABEL

SEXP-1059

(ONLY IN KIT

8620-343)

Reference

Letter Bard P/N Description Qty.

A 910-2181 15" UV-C Assembly 1

B 910-2182 Relay Assembly 1

C 910-2183 Red Indicator Light Assembly 1

D 910-2184 Door Panel Switch Assembly (Interlock Safety Device) 1

E 113-908 Bracket (WH/Q-TEC Q**H/A4 Units) 1

F 113-909 Bracket (I-TEC Units) 1

G 113-913 Bracket (Q-TEC Units) 1

H 7961-963 UV-C Warning Label 1

I Per Model Supplemental Instructions Manuals and Wire Diagrams 4/2

J 400-0467 Parts Bag – Six (6) Screws, Three (3) Zip Ties, Six (6) Pieces of Foil Tape,

Bushing, UV-C Warning Label and “UV-C LED Light Bar Installed” Label 1

K 910-2191 460V Stepdown Transformer Assembly (8620-343 Kit Only) 1

L 113-932 Transformer Enclosure (8620-343 Kit Only) 1

Manual 7960-918

Page 4 of 9

Installation

Field-supplied tools needed:

• Appropriate personal protection equipment,

including gloves and safety glasses

• Electrical meter to verify power status

• Drill

• Phillips head screwdriver

• 5/16" nut driver

• 7/8" drill bit (optional)

Installation Procedure

1. Disconnect all power to HVACR unit. Use the meter

to verify that power has been disconnected.

2. Remove outer and inner control panel covers.

3. Remove blower housing cover (large upper panel).

4. Attach two (2) magnetic clips to the UV light

assembly (see Dimensions drawing on page 2).

5. Install UV light assembly onto the blower partition

on the inside of the front ange as shown in

Figure 1.

UV light should be directed over blower

FIGURE 1

Install UV Light Assembly and Route Wires

outlets, facing evaporator coil. (Models may have air

deector or control box mounted to blower partition;

however, UV light can still be installed as shown.)

Route wires into control panel through bushing in

blower partition or copper grommet or wire bushing,

then into control panel as shown in Figure 1.

NOTE: Not all models will have bushing in blower

partition. A 7/8" hole can be drilled and

supplied bushing can be installed.

7. Kit 8620-343 (460V-3PH Units) Only: 460V

stepdown transformer can be installed in any of

these four locations: In control panel assembly, on

side ange of control panel, on blower partition or

under blower partition (see Figure 2).

8. Connect red wire from UV light assembly to

“NO” contact on the relay assembly (see Field

Installation Diagram on page 9).

9. Determine unit supply voltage—located on the

unit serial plate. Connect black wire from UV light

assembly to:

(230V-1PH) − “L2”

(230V-3PH) − “L3”

(460V-3PH) − Black Wire-Transformer

See Field Installation Diagram on page 9.

MIS-4328

CONTROL PANEL

BUSHING

(WITH MAGNETIC CLIPS)

UV LIGHT ASSEMBLY

ROUTE WIRES

THROUGH BUSHING

Manual 7960-918

Page 5 of 9

FIGURE 2

Kit 8620-343 460V Stepdown Transformer Installation Locations

MIS-4336

TRANSFORMER COVER

NOT REQUIRED

IN UNIT CONTROL PANEL

ON BOTTOM BLOWER PARTITION

TRANSFORMER COVER

REQUIRED

ON TOP BLOWER PARTITION ON SIDE FLANGE

CONTROL PANEL

Manual 7960-918

Page 6 of 9

FIGURE 3

Install Relay and Indicator Light Assemblies

MIS-4329

SPACE IS LIMITED IN CONTROL PANELS ON

SOME MODELS. INSTALL RELAY AND INDICATOR

LIGHT WHERE THERE IS SPACE AVAILABLE.

10.

Connect red wire from “COM” on relay assembly to:

(230V-1PH) − “L1”

(230V-3PH) − “L1”

(460V-3PH) − White Wire-Transformer

See Field Installation Diagram on page 9.

11. Connect short orange wire from relay assembly to

indicator light.

12. Connect short black/white wire from relay assembly

to indicator light.

13. Control panel assemblies vary due to available

control options. Find unused space on control

panel and install relay and indicator light

assemblies in control panel using self-drilling

screws provided (see Figure 3).

14. Install door panel switch into panel switch bracket

113-908 (see Figure 4). Door panel switch acts as

interlock safety device to disable UV light source

upon removal of blower access panel preventing UV

exposure.

15. Install panel switch assembly on the left side of

blower partition using self -drilling screw as shown

in Figure 4. Some models may have an air deector

installed on the blower partition; mount switch

assembly next to the blower partition as shown.

Manual 7960-918

Page 7 of 9

16. Route long orange wire from relay assembly (up to

door panel switch) and connect to “NO”. Route

orange wire from door panel switch (down to

control panel) through the blower partition and

control panel bushing as shown in Figure 1 on

page 4.

NOTE: Not all models will have bushing in blower

partition. A 7/8" hole can be drilled and

supplied bushing can be installed.

MIS-4330

DOOR SWITCH ASSEMBLY

LOCATION WHEN NO DEFLECTOR

IS USED.

DOOR SWITCH ASSEMBLY

USE BRACKET 113-908

ROUTE WIRES BEHIND

DEFLECTOR AND THROUGH

BUSHINGS TO CONTROL PANEL

SHOWN WITH

DEFLECTOR INSTALLED

1- 3/4"

INSTALL SWITCH ASSEMBLY

TO DEFLECTOR USING

SELF DRILLING SCREWS

PROVIDED

FIGURE 4

Install Panel Switch Assembly

17. Locate low voltage strip in control panel. Seat

spade end of orange wire from panel switch

assembly under the “G” terminal on the low

voltage strip assembly, then seat spade end of

black/white wire from coil on relay assembly under

the “C” terminal on low voltage strip (see Figure 5

on page 8).

Manual 7960-918

Page 8 of 9

18. Wires can be dressed with provided zip ties or

by tucking into wire channels. Ensure wires are

secured away from sharp edges and moving parts

to prevent damage.

Cover wires and plastic components within a

distance of 6" of the UV light with foil tape to

create a protective barrier from the UV light.

19. UV light will not function without blower panel

installed because of panel switch (interlock safety

switch). Do NOT press door panel switch with

blower panel removed as the UV source could

become active and create UV exposure.

Replace blower access cover (large upper panel).

Adhere UV-C Warning Label 7961-963 to blower

access panel.

Adhere “UV-C LED Light Bar Installed” Label

7961-622-0375 to unit serial plate. (Serial plate

is silver and located on the exterior of the unit

cabinet or on a service panel with “5253-039-

XXXX” printed in the lower right corner.)

20. Now that blower panel is installed, UV light

operation can be safely veried. Restore power

to unit and provide a “G” call signal from the

thermostat. Operation can be conrmed if indicator

light installed in Step 8 is ON in control panel.

Do NOT attempt to look at UV source to conrm

operation!

21. Disconnect power to unit. Replace all inner and

outer panel covers.

22. Restore power to unit.

FIGURE 5

Low Voltage Terminal Strip Connection Points

WITH SPADE IS CONNECTED

TO "C" ON LOW VOLTAGE STRIP

BLACK/WHITE WIRE

ORANGE WIRE

WITH SPADE IS CONNECTED

TO "G" ON LOW VOLTAGE STRIP

MIS-4331

UV radiation hazard.

Use only with shielding in place.

Protect eyes and skin from

exposure to UV light.

!CAUTI ON

Manual 7960-918

Page 9 of 9

FIGURE 6

Field Installation Diagram

COM

NCNO

LowVoltage

Terminal Strip

COM

NCNO

LowVoltage

Terminal Strip

L2L1

480V

COM

230v

Transformer

COM

LowVoltage

Terminal Strip

L1 Compressor

Contactor

ORANGE

UV-LIGHT

RELAY

INDICATOR

LIGHT

BLACK/WHITE

ORANGE

RED

BLACK

RED

ORANGE

BLACK

WHITE

COM

DOOR PANELSWITCH

UNIT SUPPLY VOLTAGE

460 VOLT - 3 PHASE

230 VOLT - 3 PHASE

UNIT SUPPLY VOLTAGE

230 VOLT - 1 PHASE

CONTACTOR

ORANGE

WHITE

Contactor

COM

WHITE

BLACK

ORANGE

RED

BLACK

RED

ORANGE

BLACK/WHITE

Compressor

LIGHT

RELAY

DOOR PANELSWITCH

UV-LIGHT

ORANGE

COM

WHITE

BLACK

ORANGE

RED

WHITE

BLACK

ORANGE

BLACK/WHITE

INDICATOR

LIGHT

RELAY

DOOR PANELSWITCH

UV-LIGHT

ORANGE

4214-102

BLACK/RED

BLACK

BLK/RED

BLACK

INDICATOR COMPRESSOR

RED

Andere Handbücher für 8620-343

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bard Wärmepumpe Handbücher

Bard

Bard WH301 Bedienungsanleitung

Bard

Bard 11EER WH Series Bedienungsanleitung

Bard

Bard I30H1 Bedienungsanleitung

Bard

Bard WH423D Bedienungsanleitung

Bard

Bard QTEC QH244D Bedienungsanleitung

Bard

Bard 11EER QH Series Bedienungsanleitung

Bard

Bard WPV30C Bedienungsanleitung

Bard

Bard WH241D Bedienungsanleitung

Bard

Bard PH13242-A Bedienungsanleitung

Bard

Bard GV27S1-A Bedienungsanleitung

Bard

Bard QH242 Bedienungsanleitung

Bard

Bard Q-TEC Q24H1 Bedienungsanleitung

Bard

Bard SH611D Bedienungsanleitung

Bard

Bard SH261D Bedienungsanleitung

Bard

Bard T24H1 Bedienungsanleitung

Bard

Bard QW2S1 Bedienungsanleitung

Bard

Bard SH431 Bedienungsanleitung

Bard

Bard PH11242 Bedienungsanleitung

Bard

Bard W18H1 Bedienungsanleitung

Bard

Bard WH423 Bedienungsanleitung

Bard

Bard T24H1 Bedienungsanleitung

Bard

Bard S26H1 Bedienungsanleitung

Bard

Bard Q24H2-A Bedienungsanleitung

Bard

Bard W18HB-A Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung