barkman Quarry Stone Bedienungsanleitung
Barkman Landscape Kits
Quarry Stone
Compact Fireplace
136671
2
05-2021
IMPORTANT: READ PRIOR TO INSTALLATION
It is the responsibility of the consumer to read and follow the proceeding information.
1. Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury or death.
2. Improper installation or maintenance of this product may result in damage ot property, injury or death.
3. Read the installation, operation and maintenance instructions thoroughly before installing or servicing this equipment.
4. Barkman Concrete Ltd. is not liable for any property damage or bodily injury caused by failure to follow the installation instructions,
improper use of the product or any negligence or carelessness of the consumer.
INSTALLATION AND USE
1. Improper installation, adjustment, alteration, service or maintenance can cause injury, or property damage. Read the installation
instructions thoroughly before installing the fireplace.
. DO NOT touch areas if fire is burning, severe burning may result. Clothing ignition may result.
3. Carefully supervise children near the fireplace.
4. Keep clothing, furniture, draperies and other combustibles away from the fireplace.
5. Fireplace is for outdoor use only. Place the fireplace in an area where wind won’t disturb the flames.
. DO NOT obstruct the opening of the fireplace, or otherwise obstruct the flow of air.
7. Fire brick related fire can occur when there is a failure to maintain the required clearances (air spaces) to combustible materials.
8. Certain steps in the installation process will require more than one person.
9. Curing is crucial to the operation of your fireplace. Ensure to follow the direction on page 14 of the instruction guide.
10. Plan to install the fireplace a week before intended use to allow enough time for the curing process.
11. Never leave the fireplace unattended when in use.
12. We strongly recommend the installation of a steel fireplace grate on the floor of the fireplace before starting to make fires. This makes
it easier to ignite the fire, directing heat away from the floor which extends the life of the floor by inhibiting the formation of small
cracks from excess heat. These grates are available at hardware and building supply outlets.
WARNING
DANGERS OF FIRE
1. If the information in these instructions is not followed exactly, a fire or explosion may result in property damage, injury or death.
2. Beware of flying sparks from mouth of the firebox, made up of firebrick components. Make sure that no combustible materials are within
range of firebrick components at any time.
3. Beware of extremely high temperatures in the fireplace when in use and for hours aer use. Do not put unprotected hands or arms
inside while the fireplace is lit.
305-2021
PROXIMITY TO BUILDINGS AND OTHER COMBUSTIBLE MATERIALS
1. The fireplace should be installed and used in accordance with the by-laws, regulations, local building codes and laws of your
jurisdiction. Please confirm that use of this product is in compliance with the by-laws, regulations and laws of your jurisdiction before
installing or using it.
2. Make sure that you locate your respective gas lines, wires, water pipes, and/or any above ground and underground services in your area
and install your fireplace in the proper distance away from them. Check with your provider for location and distance requirements prior
to installation.
3. This manual must be kept by the customer as long as they own their fireplace kit.
4. Check with your insurance provider concerning the installation, use, value implications and/or any other considerations in regards to
your fireplace kit.
Do not use landscape glue to seal the firebrick and firecap components as this is a fire hazard.
Only use SILICONE for this purpose. Do not overload wood into the firebox when in use.
FIRE WARNING
. DO NOT use charcoal, pressure treated lumber, chipped wood products, sappy wood (such as pine), laminated wood, or any material
other than dry medium or hard natural firewood.
. DO NOT use liquid fuel (firelighter fluid, gasoline, kerosene or similar liquids) to start or maintain a fire.
4
05-2021
This kit measures 78" h x 44" w x 40" d
MATERIALS INCLUDED:
• 12" x 8" Quarry Stone – 115 pieces
• 8" x 8" Quarry Stone – 37 pieces
• 4" x 8" Quarry Stone – 39 pieces
• Fire Brick – 83 Pieces Total
• 9" x 4" Fire Brick – 60 pieces
• 9" x 2.75" Fire Brick – 2 pieces
• 9" x 2.75" Fire Brick – 6 pieces
• 7.75" x 4" Fire Brick – 4 pieces
• 7.5" x 4" Fire Brick – 8 pieces
• 7.5" x 2.75" Fire Brick – 1 piece
• 4" x 2.25" Fire Brick– 2 pieces
• Hearth
• Mantle 1
• Mantle 2 (Front and Back)
• Mantle 3 (Front and Back)
• Mantle 4
• Firecap
• Spark Arrestor
• Tube of Landscape Glue – 2 pieces
• High Temperature Silicone – 2 pieces
• Gloves
• Plastic and Steel Shims
• Instruction Guide
OTHER ITEMS NEEDED:
• Rubber Mallet
• Caulking Gun
• Measuring Tape/Ruler
• Level
Materials
Base Preparation
If installing your Barkman Quarry Stone
Compact Fireplace on an unstructured
base, please ensure to follow these steps:
• Excavate area approx. 9 inches below
grade.
• Excavate approx. 6 inches larger than
your actual kit dimensions to ensure
a stable base.
• Fill with ¾ inch down limestone and
compact firmly.
• Level out ½ inch of sand and install
kit as per the instruction guide.
If you are installing on a solid base
such as an existing patio, base prep is
not necessary. Please proceed to the
first step.
These instructions may not refer to all
base conditions. As this kit is incredibly
heavy, base prep will greatly depend
on existing ground conditions and may
require alternate techniques.
Note: This manual was updated in
May 2021. For manual updates, check
www.barkmanconcrete.com/resources
12 x 8
Quarry Stone
8 x 8
Quarry Stone
4 x 8
Quarry Stone
9 x 2.75
Fire Brick
9 x 2.25
Fire Brick
9 x 4
Fire Brick
7.5 x 2.75
Fire Brick
4 x 2.25
Fire Brick
7.75 x 4
Fire Brick
7.5 x 4
Fire Brick
Fireplace
Hearth
Mantle
Mantle 2
(Front and Back)
Mantle 3
(Front and Back)
Mantle 4 Firecap
Spark
Arrestor
Plastic and
Steel Shims
505-2021
Instructions
2
A Lay out the second layer as shown in
the diagram.
B Check that stones are level. Use
included shims for adjustments.
USE:
(15) 12 x 8 Sierra Grey blocks
(4) 8 x 8 Sierra Grey blocks
(2) 4 x 8 Sierra Grey blocks
3
A Lay out the third layer as shown in
the diagram.
B Check that stones are level. Use
included shims for adjustments.
USE:
(7) 12 x 8 Sierra Grey blocks
(2) 8 x 8 Sierra Grey blocks
12" x 8"
1
A Lay down the first layer as shown in
the diagram.
B Check that stones are level at
every step. Use included shims for
adjustments.
USE:
(14) 12 x 8 Sierra Grey blocks
(4) 8 x 8 Sierra Grey blocks
(5) 4 x 8 Sierra Grey blocks
4" x 8" 8" x 8"
6
05-2021
5
A Repeat steps 3 and 4 twice to the
height of eight layers.
B Check that stones are level. Use
included shims for adjustments.
USE:
(26) 12 x 8 Sierra Grey blocks
(8) 8 x 8 Sierra Grey blocks
(6) 4 x 8 Sierra Grey blocks
4
A Lay down the fourth layer as shown
in the diagram.
B Check that stones are level. Use
included shims for adjustments.
USE:
(6) 12 x 8 Charcoal blocks
(2) 8 x 8 Sierra Grey blocks
(3) 4 x 8 Sierra Grey blocks
705-2021
7
A Lay down the ninth layer as shown in
the diagram.
B Check that stones are level. Use
included shims for adjustments.
USE:
(5) 12 x 8 Sierra Grey blocks
(2) 8 x 8 Sierra Grey blocks
(4) 4 x 8 Sierra Grey blocks
WARNING: Only use silicone when
securing the fire brick.
6
A Start installing the firebrick surround
inside the wall of the fireplace as
indicated by the diagram to create a
firebox.
B Install in this order: bottom first; then
le and right sides; finally the back.
C Aix firebrick pieces to the wall
using the included high temperature
silicone. Ensure that both surfaces
are dry and free of debris to allow for
optimal adhesion. Run silicone along
each horizontal layer along with the
backs of each individual piece.
USE:
(2) 4 x 2.25 Fire Bricks
(6) 7.5 x 4 Fire Bricks
(6) 9 x 2.25 Fire Bricks
(52) 9 x 4 Fire Bricks
9" x 4"
9" x 4"
4" x 2.25"
9" x 4"
9" x 2.25"
7.5" x 4"
9" x 2.25"
9" x 4"
8
05-2021
9
A Lay out the tenth layer as shown in
the diagram.
B Check that stones are level. Use
included shims for adjustments.
USE:
(8) 12 x 8 Sierra Grey blocks
(2) 8 x 8 Sierra Grey blocks
(2) 4 x 8 Sierra Grey blocks
10
A Lay out the eleventh layer as shown
in the diagram.
B Glue the block indicated in the
diagram to the Quarry Stone below.
C Check that stones are level. Use
included shims for adjustments.
USE:
(8) 12 x 8 Sierra Grey blocks
(2) 8 x 8 Sierra Grey blocks
(2) 4 x 8 Sierra Grey blocks
8
A Place the mantle into the ninth layer
as indicated in the diagram.
B Glue the mantle where is contacts
the Quarry Stone below using the
included landscape adhesive.
USE:
Mantle
Glue block
905-2021
11
A Lay down the twelh layer as shown
in the diagram.
B Check that stones are level at
every step. Use included shims for
adjustments.
USE:
(6) 12 x 8 Sierra Grey blocks
(2) 8 x 8 Sierra Grey blocks
(3) 4 x 8 Sierra Grey blocks
12
A Place and glue the remaining pieces
of the firebox.
B Double check if all the pieces are
completely flushed against the inside
wall of the fireplace.
USE:
(1) 7.5 x 2.75 Fire Bricks
(2) 7.5 x 4 Fire Bricks
(4) 7.75 x 4 Fire Bricks
(2) 9 x 2.75 Fire Bricks
(8) 9 x 4 Fire Bricks
9" x 4"
9" x 4"
7.75" x 4"
7.5" x 4"
9" x 2.75"
7.5" x 2.75"
9" x 4"
7.75" x 4"
10
05-2021
14
A Apply high temperature silicone to
the tops of the firebrick as well as
to the quarry stone supports on the
front.
B Install the Firecap on top of firebrick
as indicated in the diagram.
USE:
Firecap
15
A Place the spark arrestor at the top of
the fireplace setup as shown.
USE:
Spark Arrestor
13
A This shows how the fireplace will
look when all the firebricks installed.
Warning: Only use Silicone when
securing the Fire Brick. Allow Silicone to
set 2 hours before installing the Firecap.
Andere Handbücher für Quarry Stone
2
Inhaltsverzeichnis
Andere barkman Kamin im Innenbereich Handbücher
