Barko HARVESTER 240B Bedienungsanleitung
®
OPERATOR’S MANUAL
®
1 Banks Avenue • Superior • WI • 54880
Phone: 800-544-6532 • 715-395-6700
Fax: 800-772-2448 • 715-392-9348
Web: www.barko.com Email: [email protected]
MANUAL P/N
REVISION
DATE
Serial Number Range:
Machine Serial Number:
NOTE:
This Operator’s Manual includes precautions and procedures for safely operating your BARKO machine. This manual includes
limited service, repair and parts information. Separate BARKO Parts and Service Manuals are available from your BARKO
dealer or from BARKO directly.
Engine, attachment and other component information may be limited in this manual. See separate manufacturer manual(s)
which accompanies this BARKO machine from the factory.
The information and illustrations in this manual have been approved as accurate at the time of printing. However, this manual
may contain information on options not present on your loader. BARKO Hydraulics, LLC reserves the right to make changes
and improvements in its product at any time without notice or obligation.
800-00471
A
06/03/2019
HARVESTER
240B / 260B
240B- 11924023679 thru
260B- 11926023635 thru
®
SUPERIOR • WI • USA • www.barko.com
NOTE:
The beginning of each chapter has its own detailed table of contents.
MANUAL Table of Contents
CH-10 GENERAL INFORMATION 10-1
USE GENUINE BARKO PARTS 10-3
HYDRAULIC PRESSURE WARNING 10-4
INTRODUCTION 10-5
KNOW YOUR BARKO 10-7
SAFETY SUMMARY 10-8
WELDING SAFETY 10-13
FIRE PREVENTION 10-14
BARKO DEALER NET 10-16
ABBREVIATIONS 10-18
CH-13 MACHINE OVERVIEW 13-1
MODEL DESCRIPTION- 240B, 260B 13-3
COMMON SERVICE PARTS 13-10
MACHINE SERVICE 13-12
NEW MACHINE BREAK-IN 13-27
OPERATION 13-28
TRANSPORTING 13-39
MACHINE STORAGE 13-40
CH-18 DECALS 18-1
BOOM DECALS 18-2
CAB DECALS 18-2
SHROUD DECALS 18-5
POWER PACKAGE DECALS 18-6
CH-22 ELECTRICAL 22-1
ELECTRICAL PANEL 22-3
CH-26 HVAC 26-1
GENERAL HVAC SYSTEM 26-3
HEATER-A/C UNDER-SEAT UNIT 26-5
CH-40 CAB 40-1
OPERATOR SEAT 40-2
CAB ROOF EGRESS 40-4
HARVESTER SIDE CONSOLE 40-5
IQAN MD4 DISPLAY 40-8
RADIO / STEREO 40-41
CAB SLIDE OPERATION 40-42
CH-43 PLATFORM 43-1
PLATFORM- HARVESTER 43-3
®
SUPERIOR • WI • USA • www.barko.com
CH-46 LOWER FRAME 46-1
SIDE FRAME AY- D5 & D6 46-2
CH-50 SHROUDING 50-1
SHROUDING OVERVIEW 50-3
GULLWING DOOR 50-6
CH-60 POWER PACKAGE 60-1
CUMMINS TIER-4 DIESEL ENGINE 60-2
CH-70 HYD & FUEL RESERVOIR 70-1
RESERVOIR- HYD & FUEL 70-3
CH-80 OPTIONS 80-1
PROHEAT PRE-HEAT SYSTEM 80-2
VACUUM PUMP 80-4
®
THIS PAGE INTENTIONALLY BLANK
®
SUPERIOR • WI • USA • www.barko.com
CHAPTER
1 BANKS AVE • SUPERIOR • WI • USA • www.barko.com
®
OPERATOR
GENERAL INFORMATION
10
Table of Contents- CHAPTER 10
USE GENUINE BARKO PARTS 10-3
HYDRAULIC PRESSURE WARNING 10-4
INTRODUCTION 10-5
OTHER RESOURCES 10-6
UNAUTHORIZED PRODUCT CHANGES 10-6
KNOW YOUR BARKO 10-7
SAFETY SUMMARY 10-8
OPERATION ON SLOPED TERRAIN 10-12
WELDING SAFETY 10-13
FIRE PREVENTION 10-14
BARKO DEALER NET 10-16
PARTS TAB 10-16
MANUALS TAB 10-16
SERVICE TAB 10-17
ABBREVIATIONS 10-18
800-10004
THIS PAGE LEFT INTENTIONALLY BLANK
10-3
Remember, use only...
* GENUINE BARKO PARTS *
NOTE
This Operator’s Manual has limited parts information. A BARKO
Parts Manual will have detailed parts lists and illustrations that may
assist in performing routine maintenance.
A BARKO Service Manual will have detailed service and
maintenance procedures which will assist servicing your BARKO
machine or attachment.
This Operator’s Manual must be with the machine at all times.
Purchase BARKO Parts and/or Service Manuals
from your authorized BARKO dealer.
BARKO HYDRAULICS, LLC
1 Banks Avenue
Superior, WI 54880
715-395-6700
www.barko.com
OPERATOR’S
®
10-4
WARNING
!
Raising hydraulic pressure on this
machine above the factory approved
settings may cause death, severe
injury or property damage and will
void the warranty.
The consequences of increasing hydraulic
pressure are serious. The function of the relief
valves is to provide a fuse action to protect the
machine and the operator from overloading. When
overloaded, the machine can become stressed to a
level where parts fracture causing death, severe injury
or property damage. This is an extremely
dangerous practice.
Accordingly, you are advised that the pressure
settings of this machine are limited to the factory
approved settings. Pressures in excess of these
settings render each and all Barko warranties null and
void and constitute an obvious misuse and abuse of
our product.
BARKO HYDRAULICS, LLC
OPERATOR’S
®
10-5
®
INTRODUCTION
Model and Serial Numbers are found on the Data Plate of your machine and/or
attachment. Machines and Attachments each have their own unique S/N's. Locations of the
612/830/930/937 LH rear of front frame
Your BARKO machine has been designed and manufactured with the highest quality of
materials and care in workmanship. This Operator’s Manual is intended to assist you in safe
operation and maintaining your BARKO to keep it in peak condition. A BARKO Operator’s Manual must
be with the machine at all times. Separate Parts and Service Manuals can be obtained from your
BARKO Dealer.
Understand the correct servicing procedures before servicing your BARKO machine or
attachment. It is important to know the correct operating and servicing procedures of the machine and
all safety precautions to prevent the possibility of property damage and/or personal injury or death.
REFER TO A BARKO SERVICE MANUAL for detailed service schedules and procedures.
PHONE: 715-395-6700
EMAIL: [email protected]
Right or left hand is determined when positioned in the machine from the normal
Cylinders- The port location off center viewed from butt of cylinder.
Pump and Motor Rotation- Determined by viewing from the shaft end.
1. Right Hand (RH) or Left Hand (LH)
Know the following information before ordering parts or servicing your BARKO machine:
All parts for your BARKO machine or attachment may be ordered from your nearest BARKO
Dealer. If you are not certain of the dealer's location check our website or contact BARKO Customer
Service for assistance:
operator's seat position behind the boom or lifting arms.
WEB: www.barko.com/dealer-locator
2. Model and Serial Numbers ---- IMPORTANT!
data plate on popular BARKO models are:
70/80/110 LH or RH head plate
240/260/270 On head right side of main lift cylinder
295/495/595 RH on lower frame below platform
service procedures in this manual before servicing your BARKO machine or attachment.
It is your responsibility to know and understand ALL safety warnings and follow safe
Cylinders- ID numbers stamped on gland.
may be machine/serial number specific.
machine or attachment. BARKO warranties are included with the Operators manual and
It is your responsibility to know and understand the factory warranty for your BARKO
4. Safe Working Practices & Procedures
Grapples- Front or side head plate
3. Warranty
PAR T NO 53 9-00667
06/03/2019
Updated
OPERATOR’S
10-6
®
INTRODUCTION (continued...)
ŸSociety of Automotive Engineers (SAE) www.sae.org
ŸAssociation of Equipment Manufacturers (AEM) www.aem.org/groups/product-specific/forestry-
equipment-council-foec/
As a professional trained operator you are responsible for safety, both your own and that of
your co-workers. Your knowledge and use of all safety practices and correct servicing procedures in
this manual, and your good judgement, can be a major factor in preventing some of the thousands of
injuries and deaths caused by industrial accidents each year.
A professional operator should also be familiar with the information contained in other applicable
sources such as:
DON'T FORGET - SAFETY FIRST!
ŸOccupational Safety and Health Administration (OSHA) www.osha.gov/SLTC/logging/
ŸForest Resource Association (FRA) www.forestresources.org
ŸNational Timber Harvesting and Transportation Safety (THATS) Foundation
www.loggingsafety.com
ŸAmerican National Standards Institute (ANSI) www.ansi.org
The installation of any unauthorized attachment or changes made of any kind to this BARKO product
could affect the products ability to perform as originally intended. The products integrity, stability and it's
ability to perform safely could be at serious risk!
UNAUTHORIZED PRODUCT CHANGES:
As owner / operator of this machine, BARKO advises you that NO CHANGES ARE TO BE MADE TO
ITS PRODUCTS INCLUDING DELETIONS OR ADDITIONS OTHER THAN A BARKO APPROVED
OPTION. Any unauthorized alterations to this BARKO machine may nullify and void your BARKO
factory warranty as well as component manufacturer warranties. KNOW YOUR WARRANTY!
Contact BARKO or your BARKO dealer for information on maximum permissible operating weights and
the effects of additional options may have on your machine. Weight and stability are important factors
when considering the addition of options or attachments. BARKO will not be held responsible for
any situation that may arise resulting from any unauthorized field changes to its products.
06/03/2019
Updated
OPERATOR’S
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Barko Traktor Handbücher
