BARO BR-W2 Bedienungsanleitung
BARO SNT PRODUCT
MANUAL
www.barosnt.com
VER.1.1
2015/06/12
WIRELESS MICROPHONE & RECEIVER
1 CHANNEL SYSTEM: BR-W2
CONTENTS
www.barosnt.com
Before Use:
Device Outline………………………………………………………………...4
Device Specifications………………………………………………………...4
Device Features……………………………………………………………… 4
Package Contents…………………………………………………………… 5
Parts Listing…………………………………………………………………... 5
Cautions and Warnings………………………………………………………6
Component Descriptions:
Receiver Description and Functions………………………………………. 7
Hand Mic Description and Functions………………………………………8
Hand Mic Charger Description and Functions………………………....... 8
Installation:
Receiver Installation…………………………………………………………. 10
System Installation……………………………………………………………10
Hand Mic Installation…………………………………………………………11
Settings:
Setting the Volume……………………………………………………………12
Setting the Tone……………………………………………………………… 12
Setting the Squelch………………………………………………………….. 12
Setting the Receiver Channel…………………………………………….....13
Setting the Hand Mic Channel………………………………………………13
Operation…………………………………………………………………………………………...15
2
www.barosnt.com
Battery Replacement:
Hand Mic Battery Replacement……………………………………………. 16
Issue Diagnosis…………………………………………………………………………………… 17
Other:
Channel Frequency Chart…………………………………………………...18
Full Specifications:
Receiver………………………………………………………………………..19
Hand Mic………………………………………………………………………19
Hand Mic Charger (Optional)……………………………………………… 20
3
BEFORE USE
4
www.barosnt.com
Device Outline:
This product is a wireless device using the UHF 900MHz spectrum. It is designed for use in homes, offices,
government facilities, broadcasting centres and other locations where wireless transmission is required. The
system operates within internationally designated channel frequencies, and enables the accurate wireless
transmission of audio signals without any distortion or interference.
General Specifications (BR-W2):
Operating Frequency
925.120MHz to 937.420MHz
Oscillation Mode
62Channel . PLL synthesized
Receiving Mode
1 Channel System
Modulation Method
FM(F3G)
Total Harmonic Distortion
Less Than 0.5% (Ref
±12kHz Distortion, 1khz Mod)
Audio Frequency response
50 to 16,000Hz (
±3dB)
Audio output
100Mv / Input 10mV
S/N Ratio
More Then 60dB
Audio Outputs Type
Unbalanced / Balanced XLR
Power Supply
DC12V / 500mA / Adapter
Operation Temperature
-5
℃to 60℃
Device Features:
•Country of Origin: South Korea
•PLL synthesizer type transmitting microphones with 62 Channel settings. Freely select the operating
channel with clear audio reproduction and no interference.
•The adoption of FND makes switching operating channels simple.
•Through tone adjustments, manage the high and mid levels to avoid howling.
•Adoption of RF volume adjustment reduces noise and interference from other nearby wireless devices.
•Usage time is extended with a low-power circuit design. With a fully charge Ni-Mh battery, over 10 hours
of use is possible..
5
www.barosnt.com
Single Channel Wireless Audio System BR-W2
1 Channel Receiver
BR
-WR1
Hand Mic
BR
-WMH
Antenna
BR
-WANT
Racking
BR
-WRAC
Power Cable and Adapter
BR
-WPWR
Audio Output Cable
BR
-WCAB
Non
-rechargeable Batteries
BR
-WBAT
Optional Hand Mic Charger BR-WCH
Charger
BR
-WMC
Racking
BR
-WMCRAC
Power Cable and Adapter
BR
-WMCPWR
Rechargeable Batteries
BR
-WMCBAT
Optional Hand Mic Charger (BR-WCH)
Parts Listing
Charger
Power Cable
Mounting Bracket
PACKAGE CONTENTS
Single Channel System (BR-W2)
Hand Mic Antenna
Power Cable Audio Output Cable
AA x 2 Racking Bracket
Receiver
6
www.barosnt.com
Cautions and Warnings:
•Never handle the product or power source with wet hands.
•Ensure the product never comes into contact with water or any other liquid. Ensure it is
installed in a location where liquid will not be poured on it. This may cause electrical
shock or fire.
•If liquid has entered the product, be sure to disconnect it from all power sources, inputs
and outputs, and contact your Baro representative for product inspection.
•Only use the power cable and components that were originally supplied with the product.
Substitutions may lead to injury or fire.
•Ensure the product is not installed where it will be operating in direct sunlight. This can
lead to product overheating, failure, and possibly fire.
•Ensure the product is disconnected from during inclement weather. A power surge may
cause product damage.
•Ensure the product is installed in a well ventilated location to prevent overheating.
•Ensure the product is not installed near any flammable objects or gases.
•Ensure the product is installed in an area free from interfering wireless and radio
equipment for optimal performance.
•Do not place heavy objects on top of the product.
•Ensure the product is keep free of dirt, dust, and other objects that could potentially enter
it. This could cause product failure.
•Use common sense during the installation and use of this product to avoid any risks not
outlined in these warnings.
7
www.barosnt.com
1 Channel Receiver (BR-WR1) FRONT
1 Channel Receiver (BR-WR1) REAR
1.
Channel Status
Shows which operating channel is in use.
2.
Channel Selector
Use to navigate up and down the available channels.
3.
Volume
Set the output volume for the output audio.
4.
Channel Hold Switch
LOCK:
Channel cannot be adjusted on the receiver.
UNLOCK: Channel may be adjusted freely.
5.
Tone Volume
Set the tone (Low to High).
1.
DC Input
Connection port for power adapter.
2.
Antenna
Connection port for receiver antenna.
3.
Squelch
Adjust the
pickup range and sensitivity.
4.
AF Output
Balanced
XLR audio output.
5.
Mic
-Line
Unbalanced
¼” audio output.
6.
Power Switch
Power ON or OFF.
COMPONENT DESCRIPTIONS AND SPECIFICATIONS
3
54
21
2
1 3 4 5 6
8
www.barosnt.com
Hand Mic Description and Functions
1.
Head Case
Protects
the microphone pick-up components from damage, windscreen.
2.
Channel Status
When switching the microphone ON it will show the current operating channel. After 3
seconds “
- -” will be displayed. Switched OFF, the status window will be blank.
3.
Power Switch
Use to switch the microphone ON and OFF
4.
Channel Adjustment
Use
the channel adjustment switch when setting the channel with the receiver.
5.
Mic Handle
The area of the microphone the user should hold while operating. Unthread the handle
counter
-clockwise to reveal the Battery Case.
6.
Battery Case
The internal
storage space for the microphone batteries.
7.
Battery
2
x 1.5V AA
8.
Handle Rubber
Keeps the microphone
from rolling when placed on a flat surface.
9.
Charger (Optional)
Optional charging
base connector.
1.
Mic Holder
Place the Mic handle downward
into the base to charge.
2.
Charge
Status
LED
RED
–When microphone is
charging.
GREEN
–When charge is
completed.
3.
DC Input
Use to switch the microphone
ON and OFF
Hand Mic Charger Description and Functions
76
1 32 54
9
8
3
2
1
9
www.barosnt.com
Receiver Installation:
1. Mount the receiver in the location where it will be used permanently. Affix the racking
bracket and mount to your digital podium or racking unit as necessary.
2. Attach the receiver’s antenna.
3. Set the Volume level somewhere near the middle setting.
4. Attach the power adapter to the receiver and connect it to a power source.
5. Turn the receiver’s power switch to the ON position.
6. The status window should light and the current operating channel will be displayed.
System Installation:
1. The receiver’s output must be connected to your audio system’s amplifier or mixer.
2. Depending on the connectivity of your system you may use the Balanced or Unbalanced
output to make the connection.
*** It is best to install the receiver and mixer/amplifier near one another. Lengthening the cable
run between devices increases the chance for audio distortion.
INSTALLATION
10
www.barosnt.com
Hand Mic Installation:
1. Remove the battery cover and install the 2 x AA 1.5V batteries supplied with your
product. Be sure to install them according to the +/- symbols denoted on the battery
case.
2. Turn the power switch to the ON position and view the status window. If the batteries are
providing ample power, the status window will display the current channel. If the
batteries are weak and need to be charged or replaced, “LO” will be displayed in the
status window. If the batteries provide no power, the status window will not illuminate and
they should be charged or replaced.
3. If the batteries are sufficient, confirm the microphone’s current operating channel. Note
whether it matches the operating channel currently displayed by the receiver.
Inhaltsverzeichnis
Beliebte Mikrofonsystem Handbücher anderer Marken
Sennheiser
Sennheiser Evolution Wireless Digital EW-DX EM 2 Bedienungsanleitung
Alpha Technologies
Alpha Technologies RBMS Bedienungsanleitung
SWIT Electronics Co.,LTD.
SWIT Electronics Co.,LTD. CW-S150 Bedienungsanleitung
Shure
Shure UA844 Bedienungsanleitung
Panasonic
Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Bedienungsanleitung
Pyle
Pyle PDWM5000 Bedienungsanleitung