Barton 95029 Original Bedienungsanleitung
SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT’S
SERIAL NUMBER ON THE BACK OF THE MANUAL NEAR THE ASSEMBLY DIAGRAM (OR MONTH
AND YEAR OF PURCHASE IF PRODUCT HAS NO NUMBER)
OWNER’S MANUAL AND SAFETY INSTRUCTIONS
FOR QUESTIONS PLEASE CALL OUR CUSTOMER SUPPORT: (909) 628 0880 MON-FRI 9AM TO 3PM PST
50” WALL MOUNT ELECTRIC FIREPLACE WITH GLASS
FIRESTONE
ITEM: 95029
IMPORTANT SAFETY INFORMATION
GENERAL SAFETY WARNINGS
Read all safety warnings and instructions. Failure to follow the warnings and instructions may
result in electric shock, re and/or serious injury. Save all warnings and instructions for future
reference.
SAFETY
WARNING DO NOT use this product or any available optional equipment without rst completely reading
and understanding these instructions and any additional instructional material such as owner’s manuals,
service manuals or instruction sheets supplied with this product or optional equipment. When using an
electrical appliance, basic precautionas MUST be followed to reduce the risk of re, electric shock and
personal injury.
DO NOT mix old and new batteries.
1
DO NOT use rechargeable silver oxide cell batteries with the remote control unit.
DO NOT mix alkaline. Standard carbon-zine, or rechargeable batteries.
DO NOT switch the appliance on until is is properly installed as described in this manual.
DO NOT leave the replace unattented during use.
DO NOT operate the replace if it has a damaged cord or if it has any other malfunction.
DO NOT run the cable under carpets or rugs.
DO NOT allow the mains cable to hang over any sharp edges or hat surfaces.
This heater must be used on an AC supply only and the voltage marked on the heater must
correspond with the supply voltage.
Periodically check the cord for damage. NEVER use the appliance if there is any damage.
This heater must be used on an AC supply only and the voltage marked on the heater must
correspond with the supply voltage.
Risk of burns. This replace is HOT when in operation and heating element is ON. Power to the
replace should be turned off and the replace allowed to cool before servicing. To disconnect power
to the replace, turn controls to off, then remove plug from outlet.
Young children should be carefully supervised when they are in same room with replace. Toddlers,
young children and others may be susceptible to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the house. To restrict access to the replace, install an
adjustable safety gate to keep toddlers, young children and other at risk individuals away from the
replace and hot surfaces.
Clothing and other ammable material should not be placed on or near the replace.
Due to high temperatures, the replace should be located out of trafc and away from furniture and
draperies.
It is imperative that that the control compartments, circulating blower, and its passageway is the
replace is kept clean.
Under no circumstances should this replace be modied.
2
IMPORTANT SAFETY INFORMATION
DO NOT use the replace if any part has been under water.
DO NOT operate the replace with the glass panel removed, cracked or broken.
Servicing should only be done while the replace is disconnected from the power outlet.
Unplug replace if not being used for an extended period of time.
DO NOT use outdoors.
NEVER locate replace where it may fall into a bathtub or other water container.
DO NOT insert foreign objects into any ventilation or exhaust opening as this may cause and electric
shock, re, or damage to the replace.
Ensure clearances to combustibles are maintained when building a mantel or shelves above the
replace. Elevated temperatures on the wall or in the air above the replace can cause melting,
discoloration or damage to the decorations, a TV or other electronic components.
Repairs to electrical appliance should be made by a qualied technician only.
Overheating will result if it is accidentally covered.
NEVER immerse the product in water or other liquids.
WARNING: DO NOT open the back panel of the insert unless the power has been shut off and the
insert has been unplugged.
WARNING: Discontinue use of the electric replace if it has any of the following: Water damage, if
the insert is dented or bent, if the power cord is damaged or hot to the touch or if the unit smokes or
smells like smoke.
3
FEATURES
Add a dash of romance to your home with the warmth and mesmerizing color play of this Fire and Ice
electric replace. Its LED lights and crystals simulate ames dancing on embers while electric coils heat
the surrounding air. There’s no smoke, no chimney, and no need to build or tend this re. It is always
under your remote control - as bright and as warm as you please.
Features
Insert Dimension: 43.5” x 15.75” x 6”
Flame effect with three colors
750 and 1500 watt heat settings
Heating type: Coiled wire heat
Fan motor with aluminum blows heat from the top of the unit
Adjustable ame brightness
Materials: Metal, tempered glass
Color: Black
Package Contents
Set includes: One replace, one remote control, hardwares (brakets and screws)
Wall mounting hardware included
Crystals (pebbles) included
Instruction manual included
Description
4
Set includes: One replace, one remote control, hardwares (brakets and screws)
Wall mounting hardware included
Crystals (pebbles) included
Instruction manual included
Getting Started: Unpack the contents of the box
Heater
Wall xing bracket and screws
Remote control
1 x bracket and and 1 x bottom bracket
8 x 6 x 2 5 m m t o p b r a c k e t ; 2 x 4 * 8 m m t o x t e m p e r e d g l a s s
2 x 4*8mm and 1 x 6x25mm to x the bottom
1 instruction manual
1 b a g o f c r y s t a l e m b e r s , 1 x w h i t e b o a r d
Wall Mount Instructions
This appliance is designed to be xed to a wall at a minimum height of 300mm and the minimum
distance from the top of the heater to the ceiling should be 1000mm. The all bracket must be tted
horizontally and the cable routed to the bottom right of the heater.
A distance of 600mm from the bottom of the heater to the oor is recommended for optimum veiwing
of the feul bed.
600
Fig. 1
ASSEMBLY
5
Remove the back panel from the heater rst. See Fig 2
Drill holes with a #6 drill bit.
Fig. 2
Remove the two pieces of white screws on both sides on the heater. See Fig 3
Fix the wall bracket using the plug and 6x25mm screws provided.
Carefully lift up the heater ensuring the top rear ledge of the heater engages with the wall bracket (see
Fig. 4) and is sitting centrally. This process should be carried out by two people.
Put the crystal up to the white border then gently bring the heater down against the wall.
Fig. 3
Fig. 4
ASSEMBLY
6
Peel off the white board’s protective lm and put the crystal on the appliance.
Place the front glass over the front of the re aligning the slots in the bracket at each side of the glass
panel with the lugs on the sides of the re. Two people are required for this operatin. See Fig. 6
Fig. 5
Fix the tempered glass with 2 pieces of 4x4*8mm screws provided. See Fig. 6
Fig. 6
Fig. 7
ASSEMBLY
7
Fasten two pieces of white screws of both sides. See Fig. 5
The switches located at the center right hand side of the re. The standby switch must be switched on
rst.
Wall Insert Instructions
Take the glass from the heater rst then gently put the heater to the cut hole. This is a two person
operation. See Fig. 1
For optimum wiewing, mark the left and right screws. Fixing positions on the wall in accordance with
the appliance’s holes. See Fig. 2
Fig. 5
Fig. 2
Fig. 3
ASSEMBLY
8
Fig. 4
Place the front glass surround over the front of the aligning slots in each bracket at each side of the
glass panel with the lugs on the sides of the heater. See. Fig. 4
Take the glass from the heater rst then gently put the heater to the cut hole. This is a two person
operation. See Fig. 1
ASSEMBLY
Fix the tempered glass with 2 of the 4*8mm screws as provided.
Fig. 4
9
OPERATION
The heater can be operated either by the switches located in the top right side of the replace, or by
the supplied remote control.
Control Panel Access
The Standby switch at the center right hand side of the foreplace must be rst switched on.
It takes time for the receiver to respond to the transmitter. DO NOT press the buttons more than
once within two seconds for correct operation.
Press the ON/OFF button on the remote once, this turns the replace re effect on and
off.
Press the DIMMER button to operate the Dimmer mode. Each time the Dimmer button
is pressed, the ame intensity decreases. There are 5 brightness levels you can cycle
through.
Press the HEAT button once for the low heat setting (750W), press twice for for the
high setting (1500W) and press again to turn the heat off.
The highest temperature of the thermoset is 82°F. There are several levels you can
cycle through between 62 °F to 82 °F, as well as the OFF setting.
°F
Press the TIMER button to cycle through the timer settings: 1H to 8H, as well as the
OFF setting.
Pressing the COLOR button changes the ame color. Pressing once will turn the amber
embers to blue, pressing three times will bring you back to amber color.
Infrared Remote Control
RELEASE
PULL
RELEASE
OPEN
PUSH
Fig. 6 Fig. 7
Inhaltsverzeichnis
Andere Barton Kamin im Innenbereich Handbücher
