Bastl Instruments 60 KNOBS Bedienungsanleitung

last update: 20. 7. 2017

60 KNOBS - Assembly Guide

bastl-instruments.com

INTRODUCTION

Welcome to the assembly guide for the 60 KNOBS kit. 60 Knobs is a midi-controller, designed

specifically for the Sonic Potions’ LXR drum machine. For all the features see the manual here.

This kit doesn't require too much experience. However, it is good to have basic soldering skills and to

be able to identify electronic components before starting it. We have also included some of the best

quality solder to help you solder everything faster and better.

60 KNOBS kit consists of just one big printed circuit board (PCB), soldering components and

mounting components for both enclosure versions. The plastic enclosure is sold separately. Please

check all of your parts BEFORE you begin work to make sure you are not missing anything. See the

bill of materials (BOM) for detailed list.

BILL OF MATERIALS

60KNOBS_V.1.0 SOLDERING BOM

qty

value

part

220R

resistor

100k

resistor

1N4148

DIODE-D-5

1N4007

DIODE-D-7.5

100nF

ceramic capacitor

330nF

polyester capacitor

47uF

electrolytic capacitor

7805

voltage regulator

100mA

fuse

8 pin DIL

DIL socket - in foam

16 pin DIL

DIL socket - in foam

28pin DIL

DIL socket - in foam

CD4051BE

IC in foam

6N137

optoisolator

ATMEGA328-PU-ND / w software

16mHz

resonator

5 pin

DIN MIDI Connector

PC-GK 2.1mm

power barrel connector

12mm

small button ANGLED

POT LIN w B100k 25mm

linear potentiometer

Switch 2 P B

2p 45angled switch

20 pin

male pinheader

LED white

PCB

60KNOBS_V.1.0 MOUNTING BOM

qty

value

part

20 mm

spacer nut x nut

18 mm

spacer nut x nut

M3 x 11,5 mm

spacer nut x screw

8 mm

spacer screw x nut

M3 x 6 mm

mushroom head screw

M3 x 6 mm

countersunk head screw

M3 x 12 mm

mushroom head screw

small nut

allen key

rubber standoffs

BEFORE STARTING THE KIT...

Prepare the following tools:

● Soldering iron

● Multi-meter

● Flush cutters

● n2. hex screwdriver or allen key (enclosed with kit)

● Phillips screwdriver

● Isopropyl alcohol + smaller and clean brush (optional)

● Protective eyewear

● … and also a sufficient amount of time and patience.

We suggest that you work in a clean and a well lit and ventilated environment to avoid accidents or

losing any of the small components.

Also briefly go through this guide and make sure that you understand all the steps.

SOLDERING

Start with the smallest parts - resistors and diodes. There are three values of resistors: 220R (2x)

and 100k (2x) and 1k (1x) - take your time and check those values using a multimeter (or you can

check the color codes if you are seasoned enough). After soldering snip the leads close to the PCB

(be sure to make this step on all remaining leads in the course of this guide).

Solder also the diodes. There are just two values of them: 1N4007 - the bigger one (1x) and 1N4148

(1x). Be careful, diodes are polarized! make sure that the marking ring on the diode body matches

the marking on the circuit board.

Add the ceramic capacitors now. There are fourteen of them of the same value - 100nF (they are

marked "104" on itself).

Insert the IC sockets: 8 pin DIL (1x), 16 pin DIL (9x), 28 pin DIL (1x). Just be aware of the right

direction of sockets - there is a notch on each socket that has to match with the marked notch on

the PCB.

Bend the legs of the 7805 regulator to make them right angled and solder the regulator.

Move to soldering the switch now. You can solder just one leg first, adjust it by reheating and do the

rest then. Just be sure to solder it at the right angle and flat with the PCB. (IMPORTANT NOTE: If you

are going to clear the PCB with the isopropyl alcohol, do soldering of this part AFTER the cleaning.

The alcohol could damage the switch.)

Do also the right angled button. Keep the same quality of position as with the switch.

Add the rest of capacitors. There is 47μF electrolytic one which is polarized! The longer lead goes

to the plus (+) hole on the PCB. Solder also the polyester capacitor (330nF) which is not oriented.

Let's solder the resonator and the fuse as well. These parts are not oriented.

Now you can add the power connector. Just push it down to the PCB and solder it straight.

Insert the male headers now. Be sure to solder them straight and flat with the board. Again, you can

solder just one leg, do the adjustment and solder the rest.

Inhaltsverzeichnis

Andere Bastl Instruments Aufnahmegeräte Handbücher

Bastl Instruments

Bastl Instruments Timber Bedienungsanleitung

Bastl Instruments

Bastl Instruments KASTLE v1.5 Bedienungsanleitung

Bastl Instruments

Bastl Instruments SixtyKnobs Bedienungsanleitung

Bastl Instruments

Bastl Instruments SoftPop Bedienungsanleitung

Bastl Instruments

Bastl Instruments Knit Rider Bedienungsanleitung

Bastl Instruments

Bastl Instruments Noise Square Bedienungsanleitung

Bastl Instruments

Bastl Instruments GRANDPA v1.0 Bedienungsanleitung

Bastl Instruments

Bastl Instruments Thyme Bedienungsanleitung

Bastl Instruments

Bastl Instruments POPCORN v1.1 Bedienungsanleitung

Bastl Instruments

Bastl Instruments Tea Kick Bedienungsanleitung

Bastl Instruments

Bastl Instruments KOMPAS Bedienungsanleitung

Bastl Instruments

Bastl Instruments Timber Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch