Bauer Ecostar 6000 Allgemeine Anweisungen
Update Guide
c Bauer GmbH
V3.0
Ecostar 6000
Update Guide 08. Juni 2016 Seite 1von 12
Contents
Attention ................................................................................................................................................. 1
Software Update ..................................................................................................................................... 2
Possibility 1.......................................................................................................................................... 2
Step1: Preparing the USB stick ........................................................................................................ 2
Step2: Disconnect the power supply............................................................................................... 3
Step3: Plug in the USB stick............................................................................................................. 3
Step 4: Plug in the power supply..................................................................................................... 4
Step 5: Remove USB stick / power reset ......................................................................................... 4
Step6: Check the software version.................................................................................................. 4
Attention ................................................................................................................................................. 5
Possibility 2.......................................................................................................................................... 5
Step1: Preparing the USB stick ........................................................................................................ 5
Step2: Plug in the USB stick............................................................................................................. 6
Step3: Backup Menu ....................................................................................................................... 6
Step 5: Remove USB stick / power reset ......................................................................................... 7
Step6: Check the software version.................................................................................................. 8
Installing new languages ......................................................................................................................... 8
Step1: Preparing the USB stick............................................................................................................ 8
Step2: Delete the old language files.................................................................................................... 8
Step3: Plug in the USB stick................................................................................................................. 9
Step4: Import the new language files ............................................................................................... 10
Step5: Select the language ................................................................................................................ 11
List of figures ......................................................................................................................................... 12
Attention
It is important to update the software version or to import, to delete or to
change a language only while the irrigation is not active.
Update Guide 08. Juni 2016 Seite 2von 12
Software Update
Bauer GmbH provides several updates for the Ecostar6000 to improve the functions of the system.
The latest software versions are available on the Bauer –homepage.
There are two possibilities to update the Ecostar. The following steps describes how to make a
successful update.
Possibility 1
Step1: Preparing the USB stick
Download the actual version from the homepage e.g. “Ecostar 6000 VXX.XX.zip”. Unpack this file and
copy the four files on an empty USB stick:
Bios.inf
Ecostar.bin
EEPROM.BAK
SPIFLASH.BAK
Figure 1 - Update Files
Update Guide 08. Juni 2016 Seite 3von 12
Step2: Disconnect the power supply
Remove the plug of the at the battery or unplug the connector at the backside of the Ecostar6000
Figure 2 - Power supply
Step3: Plug in the USB stick
Plug in the USB stick at the USB port at the backside of the Ecostar6000.
Figure 3 - USB stick
Update Guide 08. Juni 2016 Seite 4von 12
Step 4: Plug in the power supply
After connecting the power supply the Ecostar6000 checks if there is an USB stick connected. If the
USB stick is recognized, a special update melody comes up and the controller starts to update the
software. During the update the display is black but at the back there should flushing three led’s.
Figure 4 - LED's flushing
The update is ready when the homescreen is shown on the display.
Figure 5 - homescreen
Step 5: Remove USB stick / power reset
Remove the USB stick and plug off and on the power supply to make a reset.
Step6: Check the software version
Check if the correct version is installed. This information is available at “Menu” -> “Service / Info”->
“Info”.
Figure 6 - installed SW version
1
1
The shown software version could be higher.
Update Guide 08. Juni 2016 Seite 5von 12
Attention
There is a second possibility to update the Ecostar if the update was not
successful.
Possibility 2
Step1: Preparing the USB stick
Download the actual version from the homepage e.g. “Ecostar 6000 VXX.XX.zip”. Unpack this file and
copy the four files on an empty USB stick:
Bios.inf
Ecostar.bin
EEPROM.BAK
SPIFLASH.BAK
Figure 7 - Update Files
Update Guide 08. Juni 2016 Seite 6von 12
Step2: Plug in the USB stick
Plug in the USB stick at the USB port at the backside of the Ecostar6000.
Figure 8 - USB stick
If the USB stick was recognized the USB symbol is shown at the right corner.
Figure 9 - USB symbol
Step3: Backup Menu
Press “Menu” and open the “Backup“. Enter the Backup Menu with “8570” and open the
second page by pressing “down arrow”.
Update Guide 08. Juni 2016 Seite 7von 12
Figure 10 –Backup page 2
Press „restart“, a special update melody comes up and the controller starts to update the software.
During the update the display is black but at the back there should flushing three led’s.
Figure 11 - LED's flushing
The update is ready when the homescreen is shown on the display.
Figure 12 - homescreen
Step 5: Remove USB stick / power reset
Remove the USB stick and plug off and on the power supply to make a reset.
Update Guide 08. Juni 2016 Seite 8von 12
Step6: Check the software version
Check if the correct version is installed. This information is available at “Menu” -> “Service / Info” ->
“Info”.
Figure 13 - installed SW version
2
Installing new languages
If there is a big system update available for the Ecostar6000 it is also necessary to install or to update
the language files. For this the newest versions are available to download at the Bauer homepage.
Step1: Preparing the USB stick
Download the actual version from the homepage e.g. “LanguageVX.XX.zip”. Unpack this file and copy
the two files on an empty USB stick:
Figure 14- language files
Step2: Delete the old language files
It is important to delete the old installed language files. At “Menu” -> “base setting” -> press button
where the actual selected language is shown e.g. “Deutsch”
2
The shown software version could be higher.
Update Guide 08. Juni 2016 Seite 9von 12
Figure 15: Sytem setting
Press button next „select language
Figure 16 - change language
The list of all imported language appears -> delete the selected language by pressing “delete”
Figure 17 - delete language
After pressing delete the Ecostar is making a reset, this can take several seconds.
Step3: Plug in the USB stick
Plug in the USB stick at the USB port at the backside of the Ecostar6000
Andere Handbücher für Ecostar 6000
2
Inhaltsverzeichnis
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
