BD BDS4012-50 Bedienungsanleitung
bello-digital.com
A316
Bell’O International Corp; 711 Ginesi Drive, Morganville, NJ 07751
Made in China • Printed in China • Fabricado en China • Impreso en China • Fabriqué en China • Imprimé en Chine
www.tsicustomerservice.com
bello-digital.com
1-888-235-7646
Twin-Star International, Inc. Delray Beach, FL 33445
Made in China • Printed in China • Fabricado en China • Impreso en China • Fabriqué en Chine • Imprimé en Chine
MODEL/ MODÈLE/ MODELO:
BDS4012-60 / BDS4012-50
Sound Shelf
bello-digital.com
A316 1
If at any time you are unclear about the directions and believe you need further assistance, contact
customer service at: 1-888-235-7646 (US/Canada) from 8:30am – 5:30pm EST, Monday through
Friday.
NEVER EXCEED THE MAXIMUM LOAD CAPACITY OF: 80 lbs (36.3kg) WHEN INSTALLED INTO
2 OR MORE STUDS, CONCRETE OR CONCRETE BLOCK WALLS.
Wood studs should be 2” x 4”, at minimum: 1.5” x 3.5” (38mm x 89mm). Designed to be
mounted to 2” x 4” wood studs that are spaced 16” on center.
is speaker shelf was designed to be installed and utilized ONLY as specied in this manual.
Twin-Star International. will not be responsible for failure to assemble as directed or for the
improper assembly, use, or incorrect assembly.
If the mounting bracket will be attached to any structure other than specied in this
manual, only a licensed professional contractor/installer should perform this installation.
e supporting structure must support, at minimum, four times the combined weight of
the sound shelf, plus anything place on top of it. It is the responsibility and liability of the
installer to ensure the suitability of the supporting structure.
Check carefully to ensure that there are no missing or damaged parts. Never use defective parts.
To receive replacement or missing part(s) under this Warranty, visit our website at www.bello-
digital.com or call our Customer Service Department at 1-888-235-7646. Please have the model
number, lot code, part number(s) and your sales receipt or other proof of purchase available for
reference. We will ship you any necessary replacement parts in the Continental United States or
Canada.
Specications are subject to change without notice.
Precautions
Furniture Guideline
It is best to keep your furniture in a climate-controlled environment. Temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep
furniture away from direct sunlight as sun may damage the nish. Proper care and cleaning
at home will extend the life of your purchase. Following these important and helpful tips will
enhance your furniture as it ages.
A touch-up pen has been provided to repair any small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years. ank you for your purchase!
bello-digital.com
A316 2
Packing Content
Hardware Kit
Part Desciption Qty
AInstallation Template 1
B Wall Bracket 1
CSound Shelf 1
DLe Corbel 1
E Right Corbel 1
A
B
CD
E
Part Description Quantity Picture
Lag Bolt
0.3 in. x 2.68in.
7.6 mm x 62 mm
Masonry Anchor
0.48 in. x 1.75 in.
12.3 mm x 44.5 mm
Washer
outer dia. 19 mm (0.75in.)
inner dia. 8.5 mm( 0.33in.)
6
6
BB
AA
6
CC
4
DD
Screw
0.25 in. x 1.1 in.
6.3 mm x 25 mm
bello-digital.com
A316 3
Hardware Kit
Part Description Quantity Picture
1
GG Touch-up Pen
1
HH Power Supply
1
II RCA Stereo Cable
1
JJ Remote Control
Screw (installed in bracket)
0.25 in. x 1.1 in.
6.3 mm x 25 mm
6
EE
Washer (installed in bracket)
outer dia. 19 mm (0.75in.)
inner dia. 6.5 mm( 0.25in.)
6
FF
bello-digital.com
A316 4
Necessary Tools
Phillips head
Screwdriver
Pencil
Drill Bit
Wood: 3/16”
Masonry:1/2”(12.5mm)
Masking Tape
Socket Wrench
(optional)
Stud Finder Drill
Level
bello-digital.com
A316 5
• Carefully place the shelf upside down on a so surface so the wood is not damaged. Loosen
the bolt EE on the wall plate and remove the wall plate B from the speaker shelf C.
• Keep the bolts EE and washers FF for reinstalling the sound shelf to the wall bracket aer the
wall bracket has been installed on the wall (see page 11).
Remove the wall plate
EE
FF
EE
FF
bello-digital.com
A316 6
• Attach Le Corbel D and right Corbel E to the back of Sound Shelf C as shown. Carefully
screw the corbels in as shown using screws DD.
Attaching e Corbel
D Le Corbel
E Right Corbel
C Sound Shelf
DD Screw
0.25 in. x 1.1 in.
6.3mm x 28mm
bello-digital.com
A316 7
• FIND THE WOOD STUD:
Using a stud nder, nd the exact location of the studs to which you want to attach the wall
mount. Mark the right and le side to determine the center of each stud.
Installing e Sound Shelf Bracket In Wood
FOR WOOD STUD WALLS INSTALLATIONS, SEE PAGE 8.
FOR MASONRY INSTALLATIONS, SEE PAGE 9.
bello-digital.com
A316 8
Installing e Sound Shelf Bracket In Wood
A
BB
BB
BB
BB
BB
B
AA
AA
AA
AA
AA
AA
BB EE
EE
EE
EE
EE
EE
• DETERMINE INSTALLATION LOCATION:
Use the Installation Template in order to determine the location on the wall that you want to
install the shelf.
Carefully drill six holes at 2.5” deepth through apppropriate points “A”, “B”, ‘’C’’, “D”, “E” and
“F” in the installation template.
Mount into 3 studs as shown above.
If the bracket will not line up with 3 studs,
Center the bracket on 2 studs.
A
bello-digital.com
A316 9
Installing e Sound Shelf Bracket In Masonry
• DRILL PILOT HOLES
Aer you have determined your desired Sound Shelf location, Line up the Installation
Template to ensure you will not drill into any mortar joints. Tape the Installation Template in
place securely on the wall with masking tape. Use a Level. Carefully drill six holes using a
1/2” (or 12.5 mm) masonry drill bit Into holes A, B, C, D, E and F. Each hole should be at
least 2.5” (63mm) deep.
Note: Each hole should be at least 5” apart.
at means the hole on the top row of the wall bracket should be three slots away from the
hole on the bottom row of the wall bracket.
DO NOT DRILL INTO MORTAR JOINTS! DRILL HOLES AT LEAST 1” (25.4 MM) FROM
THE JOINTS. USE A NEW DRILL BIT TO ENSURE OPTIMUM HOLDING ABILITY. DO
NOT USE A HAMMER DRILL!
• Insert the anchors CC:
Place the anchors CC, the end that spreads open rst, into the hole, Tap the anchor with a
hammer until it is ush with the wall.
EE
EE
EE
EE
EE
EE
BB
BB
CC
A
CC
CC
CC
CC
63mm
2.5
EE
EE
EE
EE
EE
EE
BB
BB
CC
A
CC
CC
CC
CC
63mm
2.5
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Beliebte Sprecher Handbücher anderer Marken
Bowers & Wilkins
Bowers & Wilkins 4 Bedienungsanleitung
Sonance
Sonance SONOS OUTDOOR Series Bedienungsanleitung
Electro-Voice
Electro-Voice EVID FM4.2 Bedienungsanleitung
Pioneer
Pioneer XW-HTD630 Bedienungsanleitung
Onn
Onn BWA16AA002 Bedienungsanleitung
HP
HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung