Bdcom S1010-8P-120 Bedienungsanleitung

专业网络科技

User Guide

100M PoE Switch

S1010-8P-120/S1006-4P-65

Disclaimer

Please note that the manual is for reference only. It does not cons tute a legal contract or a commitment between

BDCOM and any person or en ty. Although every eﬀor t has been made to ensure all the informa on is

correct ,inaccuracies or typographical errors may s occur. In no event shall BDCOM be responsible or liable, directly or

indirectly, for any damage or loss caused or alleged to be caused by or in connec on with the manual.

BDCOM reserves the right to alter, update and other wise change the informa on contained in the manual from me to

me without no e.

Introduction

Overview

S1010-8P-120/S1006-4P-65 are Power Over Ethernet switch. The PoE ports can automa ally detect and

supply power with those IEEE 802.3af/at compliant Powered Devices (PD). The power is transmi ed along with

data by one single cable allowing you to expand your network where there are no power lines or outlets and

which allow you to expand devices such as AP, IP Cameras or IP Phones, etc.

The PoE Switch have VLAN funcon that improve the network environment and reduces network maintenance

costs.

Port Feature

Model

10/100Mbps RJ45 Port

PoE Port

PoE Standard

S1010-8P-120

Port1~8

IEEE802.3af/at

S1006-4P-65

Port1~4

Product Appearance

Front panel

The Front Panel of the S1010-8P-120 consists of 10-Por t 10/100M Auto-Nego a on Ethernet R

J45 Por t. The LED indicators are also on located on the panel.

DIP Switch

The DIP switch in located in the le panel.

Standard: the factory default mode, can normally communicate between port 1~10.

VLAN: 1-8 port can be isolated each other, but 1-8 port can connect to 9/10 port a er open VLAN model to stop

broadcast storm Which can increase forwarding rate of frame.

Extend: Up to 250m PoE distance.it allows you to expand you network via Ethernet cable to where there is no power

Line or outlet but where you want to ﬁx device such as IP Cameras.

LED indicator

LED Color Func on

PWR Green Oﬀ: No Power supply.

Light: Indicates the switch has power.

LNK/ACT Green

Oﬀ: No device is connected to the corresponding port.

Light: Indicates the link through that port is successfully

Established at 10/100Mbps.

Blink: Indicates that the Switch is ac vely sending or

Receiving data over that port.

PoE Orange

Oﬀ: No PoE powered device (PD) connected.

Light: There is a PoE PD connected to be port, which

Supply power successfully.

Blink: Indicates port abnormal power supply.

The Front Panel of the S1006-4P-65 consists of 6-Por t 10/100M Auto-Nego a on Ethernet R J45 Por ts, The LED

indicators also on located on the panel.

DIP Switch

The DIP switch is located in the le panel.

Default mode: when open default mode ,the poe switch can normally communicate between port 1~6

CCTV mode: 1-4 port can be isolated each other .but 1-4 port can connect to 5, 6 port a er open CCTV to stop

broadcast storm which can increase forwarding rate of frame. The CCTV mode, allows you to expand you network via

Ethernet cable to where no power line or outlet .

Note: A er change the mode, in order to the corresponding conﬁgura on take eﬀect.the PoE switch need to restart

manually restart the PoE switch.

5 6

PoE

4*10/100Mbps PoE Port

2*10/100Mbps Port

CCTV

OFF ON

PoE

DATA 10/100M

BDCOM S1006-4P-65

DIP Switch

Power

LED indicator

LED

Color

Func on

PWR Orange Oﬀ: No Power supply.

Light: Indicates the switch has power.

DATA Green

Oﬀ: No device is connected to the corresponding port.

Light: Indicates the link through that port is successfully

established at 10/100Mbps.

Blink: Indicates that the Switch is ac vely sending or

receiving data over that port.

PoE Orange

Oﬀ: No PoE powered device (PD) connected.

Light: There is a PoE PD connected to be port, which

supply power successfully.

Blink: Indicates port abnormal power supply.

The rear panel of S1010-8P-120 indicates AC inlet power socket .

Rear Panel

The rear panel of S1006-4P-65 indicates AC inlet power socket .

Grounding Column

Power Socket

max

Power Socket

Grounding Column

Rear Panel

Power socket

Connect the female connector of the power cord here, and the male connector

to the AC (Alterna g Current) power outlet. Please make sure the voltage of

the power supply meets the requirement of the input voltage

Grounding

The switch already comes with lightning protec on mechanism. You can

also ground the switch through the PE (Protec g Earth) cable of AC cord

or with Ground Cable.

Cau on：Please use the provided power cord.

Make sure the power socket has a good contact with the ground.

Installation

Package Contents

▄PoE Switch......................................... 1

▄Power Cord........................................ 1

▄User Guide. ....................................... 1

▄Accessories(Rack angle iron*2, Rack installaon bolt*8, plas cushion*4)

Caution：If any part is lost and damaged, please contact your local agent immediately.

Safety Precautions

To avoid any device damage and bodily injury caused by improper use, please observe the following

rules.

▄Keep the power oﬀduring the installa on.

▄Wear an ESD-preven ve wrist strap, and make sure that the wrist strap has a good skin contact

and is well grounded.

▄Use only the power cord provided with the switch.

▄Make sure that the supply voltage matches the speciﬁca ons indicated on the rear panel of the

switch.

▄Ensure the vent hole is well ven ated and unblocked.

▄Do not open or remove the cover of the switch.

▄Before cleaning the device, cut oﬀthe power supply. Do not clean it by the waterish cloth, and

never use any other liquid cleaning method.

Desktop Installation

Install the Switch on a desktop, please a ach these cushioning rubber feet provided on the

bo om at each corner of the Switch in case of the external vibra on. Allow adequate space for

ven a on between the device and the objects around it.

The S1010-8P-120 Desktop Installa on

The S1006-4P-65 Desktop Installa on

Wall-mounted installation

In the ﬁrst two ﬁxed screw on the wall as shown in the ﬁgure below

Aim at the two ﬁxed hole switches, and the machine smoothly on the screw

(S1010-8P-120)

Default

VLAN

CCTV

(S1006-4P-65)

Turn on the switch

Plug in the nega ve connector of the provided power cord into the power socket of the device,

and the posi ve connector into a power outlet . A er the device is powered on, it begins the Power-

On Self-Test. The PWR LED indicator will light on all the me.

Appendix Specification

Model S1010-8P-120 S1006-4P-65

Standard IEEE802.3, IEEE802.3u, IEEE802.3az, IEEE802.3x, IEEE802.3af, IEEE802.3at

Port 10*10/100Mbps

Auto-Nego a on RJ45 Port

6*10/100Mbps

Auto-Nego a on RJ45 Port

PoE Port Port1~8 Port1~4

PoE Power Output 32W Max

PoE Power on RJ-45 Mode A 1/2(+) 3/6(-)

VLAN and CCTV Support

PoE total 120W 60W

Forwarding Mode Storage-and-Forward

Switching Capacity 2G 1.2 G

Forwarding Rate 1.488Mpps 0.89Mpps

Input Power Supply AC 100-240V 50/60Hz

Opera on Temperature 0℃~40℃

Storage Temperature -40 ℃~70℃

Opera on Humidity 10%~90%RH non-condensing

Storage Humidity 5%~90%RH non-condensing

MAC Address Table 8K, Auto-learning, Auto-aging 2K, Auto-learning, Auto-aging

Fan Fanless

Dimensions（L*W*H) 220*150*44mm 160*93*32mm

Network Media(cable)

10BASE-T: UTP category 3,4,5 cable (≤100m)

100BASE-TX: UTP category 5 cable (≤100m)

100BASE-FX:MMF,SMF

上海博达数据通信有限公司

Shanghai Baud Data Communi cation Co., LTD.

网址 Web: www. bdco m.co m.cn

地址 Add: 上海浦东张江高科技园区居里路123 号

N o .123, Juli Road,Pudong Zhangjiang High-Tech Park,Shangha i

邮编 Zip Code: 201203

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung