BEA IXIO-ST Bedienungsanleitung

IXIO-STINDUSTRIAL

75.5785.01 IXIO-ST UL INDUSTRIAL 20140402 Page 1 of 8

1. LCD

2. AIR-curtain width adjustment

3. AIR-lenses

4. cover

DESCRIPTION

5. main connector

6. main adjustment knob

7. AIR-curtain angle adjustment knob

ENGLISH

(US Version)

Safety sensor

for industrial doors

ACCESSORIES

10IMB: Mounting Bracket 10ICA: Ceiling Adapter 10WRC: Clear Rain Cover 35.1286: Black Cover

35.1302: White Cover

35.1303: Silver Cover

CDA: Curved door accessory

max. 2 in

** SEE APPLICATION NOTES OR CONTACT BEA FOR TECHNICAL SUPPORT

12-24 V AC, 50/60 Hz

12-35 V DC

Max 2.5 W

SUPPLY VOLTAGE

NOT USED

SAFETY INPUT

TEST

OUTPUT **

Sensor connectivity (power and relays) must utilize only the supplied harness.

Sensor power must be supplied from a Class 2 supply source limited to 15 W.

Sensor is intended to be monitored for proper operation by the door operator or system.

Harness shall be routed separated from any Mains or non-Class 2 voltage cable for correct operation or shall be rated for the Mains voltage,

and suitable protection and routing means shall be used according to National and Local Codes to prevent damage to the harness.

Page 2 of 8 75.5785.01 IXIO-ST UL INDUSTRIAL 20140402

MOUNTING & WIRING

TIP!

Mounting and wiring are compatible with the Wizard.

RED

BLACK

WHITE

GREEN

BROWN

BLUE

PURPLE

YELLOW

* Output status when sensor is operational

SENSOR

WIDTH

TIP!

Always

remember to

also adjust the

width via the

LCD or remote

control

(see p. 5)

The arrow position determines the width of the detection ﬁeld.

SAFETY ZONE

Activate the visible spots.*

ANGLE

* Visibility depends on external conditions

** The distance between the inner curtain of the inside door sensor and the inner

curtain of the outside door sensor should always be smaller than 8 inches.

The size of the detection ﬁeld varies according to the mounting height of the sensor.

The full door width must be covered.

Mounting

height

Detection

width

6.6 ft

7.2 f t

8.2 ft

9.8 ft

11.5 ft

6.6 ft

7.2 f t

8.2 ft

9.8 ft

11.5 ft

Always verify the actual detection ﬁeld width

with this user’s guide and not the Spotﬁnder,

which detects the whole emitted ﬁeld.

max.

3.5 in**

CLOSER

AWAY

PUSH

DOOR

If necessary, adjust the AIR-curtain

angle (from -7° to 4°, default 0°).

75.5785.01 IXIO-ST UL INDUSTRIAL 20140402 Page 3 of 8

IMPORTANT! Walk test the proper operation of the installation before leaving the premises.

4SETTINGS

Adjust the sensor by LCD or remote control (see p. 4 and 5)

SETUP

SETUP 1 (QUICK)

SETUP 2 (ASSISTED)

2 s

4 s

STEP OUT OF THE INFRARED FIELD!

reference picture

test of full door cycle +

reference picture

Page 4 of 8 75.5785.01 IXIO-ST UL INDUSTRIAL 20140402

* SEE APPLICATION NOTES OR CONTACT BEA FOR TECHNICAL SUPPORT

HOW TO USE THE LCD?

PUSH

TO SELECT

PARAMETER

SCROLL

UP-DOWN

CHANGING A VALUE

SCROLL

VALUES

UP-DOWN

PUSH

TO SAVE

NEW VALUE

new value is

displayed

more values are

displayed

current value is

displayed

To adjust contrast, push and turn

the grey button simultaneously.

During normal operation only.

Negative display = active output

DISPLAY DURING NORMAL OPERATION

Activation Safety

displayed value = saved value

displayed value = factory value

FACTORY VALUE VS. SAVED VALUE

Select Back to

eturn to previous

menu or display.

Select More to go

to next level:

- basic settings

- all settings

- diagnostics

Select your language before

entering the ﬁrst LCD-menu.

Available for the ﬁrst 30 seconds after

power-on of the sensor .

NAVIGATING IN MENUS

Scroll menu

items

Push to enter

the LCD-menu

Enter password if

necessary

Not during the ﬁrst

minute after power-on

of the sensor.

Password

XXXX

CHANGING A ZIP CODE *

ZIP code ZIP code ZIP code ZIP code ZIP code ZIP code

ZIP code ZIP code

ID #

H24 1 56-KG4

01 0 800/02D

E24 1 56 KG4

01 0 800 02F

E24 1 56-KG4

01 0 800/02F

E24 1 56-KG4

01 0 800/02F

H24 1 56-KG4

01 0 800/02F

H24 1 56-KG4

01 0 800/02F

... Validate the last digit in order to activate the new ZIP code:

- v = valid ZIP code, values will be changed accordingly

- x = invalid ZIP code, no values will be changed

- v/x = valid ZIP code, but from a different product.

Only available values will be changed.

VALUE CHECK WITH REMOTE CONTROL

Pressing a parameter symbol on your remote control,

displays the saved value directly on the LCD-screen.

Do not unlock ﬁrst.

* SEE APPLICATION NOTES OR CONTACT BEA FOR TECHNICAL SUPPORT

75.5785.01 IXIO-ST UL INDUSTRIAL 20140402 Page 5 of 8

Select your language before

entering the ﬁrst LCD-menu.

Available for the ﬁrst 30 seconds after

power-on of the sensor .

ZIP all parameter settings in zipped format

ID # unique ID-number

CONFIG P/N conﬁguration part number

SOFT P/N software part number

ERROR LOG the last 10 errors, time since last error

AIR: SPOTVIEW view of spot(s) that trigger detection

AIR: C1 ENERG signal amplitude received on curtain 1

AIR: C2 ENERG signal amplitude received on curtain 2

POWERSUPPLY supply voltage at power connector

OPERATINGTIME power duration since ﬁrst startup

RESET LOG delete all saved errors

RC PASSWORD password for remotre control login

ADMIN enter code to access admin mode

BACK

OVERVIEW OF SETTINGS

Back

BASIC

0123456789

TEST * off on

AIR: WIDTH

Always additionally adjust the

arrow position on the

sensor with a screwdriver.

AIR: OUTPUT * NO

Back

ALLDIAGNOSTICS

AIR: FREQ AB

AIR: WIDTH

Always remember to also adjust

the arrow position on the

sensor with a screwdriver.

AIR: NUMBER service

mode 12

Service Mode = no IR detection during 15 minutes (maintenance).

AIR: PRESTIME 30 s 1 min 2 min 5 min 10 min 20 min 60 min ∞

REDIRECTION motion motion

presence

activation output is active in case of: 0 motion detection

1 motion or presence detection

FACTORYRST restore to factory values

NO: normally open

NC: normally closed

AIR: OUTPUT * NO

NO: normally open

NC: normally closed

TEST * off on

AIR: IMMUNITY normal enhanced mode B

Sensors mounted close to each other

should have a different frequency.

Page 6 of 8 75.5785.01 IXIO-ST UL INDUSTRIAL 20140402

E8 2Replace sensor.

1Enter the correct password. To access the

sensor without a password, cycle power.

Sensor may be accessed for 1 minute.

The LCD or remote

control does not

react.

The sensor is protected by

a password

TROUBLESHOOTING

The ORANGE LED

ﬂashes 1 x.

The ORANGE LED

ﬂashes 2 x.

The ORANGE LED

ﬂashes 4 x.

The ORANGE LED

is on.

The RED LED ﬂashes

quickly after an

assisted setup.

The RED LED

ﬂashes

sporadically.

The LED and the

LCD-display are off.

The reaction of

the door does not

correspond to the

LED-signal.

The sensor signals

an internal fault.

The power supply voltage

is too low or too high.

The sensor does not receive

enough AIR-energy.

The sensor encounters

a memory problem.

The sensor vibrates.

The sensor sees the door

during the assisted setup.

The sensor sees the door.

The sensor is disturbed

by external conditions.

Check power supply (in the diagnostics menu of the LCD).

Check wiring.

Check the angle and width setting of the AIR-curtains.

Increase AIR-immunity ﬁlter to value 2 (enhanced).

Cycle power supply.

If orange LED turns on again, replace sensor.

Check the angle of the AIR-curtains.

Launch a new assisted setup.

Attention: Do not stand in the detection ﬁeld!

Check output conﬁguration setting.

Check wiring.

Check if the sensor is mounted ﬁrmly.

Check position of cable and cover.

Increase the AIR-immunity ﬁlter to value 2 (enhanced).

Launch an assisted setup and adjust the AIR angle.

Cycle power supply.

If orange LED ﬂashes again, replace sensor.

Cycle power supply.

Check wiring.

The ORANGE LED

ﬂashes 5 x.

The sensor receives

too much AIR-energy.

Check the angle of the AIR-curtains.

Decrease the AIR immunity ﬁlter to value 1 (normal).

The ORANGE LED

ﬂashes 8 x.

The AIR power emitter is

faulty.

Relearn AIR.

Download the BEA DECODER

app for a quick overview

of settings

75.5785.01 IXIO-ST UL INDUSTRIAL 20140402 Page 7 of 8

INSTALLATION

Avoid extreme

vibrations.

Do not cover the sensor. Avoid moving objects

and light sources in

the detection ﬁeld.

Avoid highly

reﬂective objects in

the infrared ﬁeld.

It is recommended to clean

the optical parts at least once

a year or more if required due

to environmental conditions.

Do not use aggressive

products to clean

the optical parts.

• The device should not be used for purposes other than its intended use. All other uses cannot be

guaranteed by the manufacturer of the sensor.

• The installer of the door system is responsible for carrying out a risk assessment and installing the sensor and

the door system in compliance with applicable national and international regulations and standards on door

safety.

• The manufacturer of the sensor cannot be held responsible for incorrect installations or inappropriate

adjustments of the sensor.

• The Sensor should be properly installed and adjusted and the proper functioning of the Sensor, when

installed with an end product, as intended in UL 325 standard, shall be veriﬁed by the installer.

Only trained and

qualiﬁed personnel

may install and setup

the sensor.

The warranty is invalid if

unauthorized repairs are

made or attempted by

unauthorized personnel.

Always test the proper

operation of the

installation before

leaving the premises.

The door control unit

and the door cover

proﬁle must be correctly

grounded.

MAINTENANCE

SAFETY

LED-SIGNAL

Motion

detection

Presence

detection

LED ﬂashes LED ﬂashes

quickly LED is off

LED ﬂashes

x times

LED ﬂashes

red-green

* SEE APPLICATION NOTES OR CONTACT BEA FOR TECHNICAL SUPPORT

Page 8 of 8 75.5785.01 IXIO-ST UL INDUSTRIAL 20140402

©BEA|Originalinstructions|75.5785.01IXIO-STULINDUSTRIAL20140402

TECHNICAL SPECIFICATIONS

Supply voltage:

Power consumption:

Mounting height:

Temperature range:

Degree of protection:

Applicable directives:

Presence

Typical response time: < 200 ms (max. 500 ms)

Active infrared with background analysis

Spot: 5 cm x 5 cm (typ)

Number of spots: max. 24 per curtain

Number of curtains: 2

Solid-state-relay

(potential and polarity free)

Max. contact current: 400 mA

Max. contact voltage: 42 V AC/DC

Automatic Holdtime: 0.3 or 1 s

Sensitivity: Low: < 1 V; High: > 10 V (max. 30 V)

Response time on test request: typical: < 5 ms

Detection mode:

Technology:

Output:

Test input *:

Speciﬁcations are subject to changes without prior notice.

All values measured in speciﬁc conditions.

12 V - 24 V AC, 50/60 Hz; 12 V - 30 V DC (15 W Class II)

< 2.5 W

6.5 ft to 11.5 ft (local regulations may have an impact on the acceptable mounting height)

Sensor: -31°F to +131°F

LCD: 14°F to +131°F

0-95% relative humidity, non condensing

IP54

R&TTE 1999/5/EC; EMC 2004/108/EC; MD 2006/42/EC; RoHS 2002/95/EC

PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING

FCC

ANSI / AAADM

CONTACT

BEA Inc.

G9B

This device can be expected to comply with Part 15 of the FCC Rules provided it is assembled in exact accordance with the

instructions provided with this kit. Operation is subject to the following conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received including interference that may cause undesired

operation.

Andere Handbücher für IXIO-ST

Inhaltsverzeichnis

Andere BEA Sicherheitssensor Handbücher

BEA

BEA ACTIV8 ONE ON Bedienungsanleitung

BEA

BEA IXIO Series Bedienungsanleitung

BEA

BEA Eagle5 Bedienungsanleitung

BEA

BEA CRYSTAL Bedienungsanleitung

BEA

BEA SBK-30R Bedienungsanleitung

BEA

BEA PHOENIX EX Bedienungsanleitung

BEA

BEA G3 Bedienungsanleitung

BEA

BEA Matrix2-S Bedienungsanleitung

BEA

BEA LZR FLATSCAN S Bedienungsanleitung

BEA

BEA MS51W Bedienungsanleitung

BEA

BEA FOCUS 2 Bedienungsanleitung

BEA

BEA 10LZRWIDESCAN Bedienungsanleitung

BEA

BEA MATRIX-3 Bedienungsanleitung

BEA

BEA LZR-FLATSCAN 3D SW Bedienungsanleitung

BEA

BEA IXIO-DT1 Bedienungsanleitung

BEA

BEA IXIO-ST INDUSTRIAL Bedienungsanleitung

BEA

BEA LZR-MICROSCAN T Bedienungsanleitung

BEA

BEA FALCON EXXL Bedienungsanleitung

BEA

BEA IXIO-SO1 I Bedienungsanleitung

BEA

BEA FAAC XV1 Bedienungsanleitung

BEA

BEA IXIO-ST INDUSTRIAL Bedienungsanleitung

BEA

BEA WIZARD II SMR Bedienungsanleitung

BEA

BEA IXIO-SO1 I Bedienungsanleitung

BEA

BEA FLY Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung