Beam RST701 Bedienungsanleitung

These Iridium antennas are designed to be installed in what is referred to as a “Bulk Head Mount” installation,

these antennas are not supplied with a cable and a suitable cable within specification should be used. The

antennas are designed for permanent installations and will require drilled holes and screws to affix them in

place.

The GPS antenna have SMA connectors and the Iridium TNC. The 701 require 1 drilled hole and the hexagon

locking nut used to secure the antenna in place.

The 703, 704 & 719 require 4 screws (supplied) to affix the antenna in place.

To install the antenna you will need to;

1. Use an existing mounting hole or drill a hole that will enable the antenna connector to pass through

2. The hole size should not exceed the size of the hexagonal locking nut

3. Remove the hexagon locking nut from the base of the antenna

4. Secure the hexagonal nut in place on the base of the antenna and tighten antenna firmly in place

5. If this is has screw holes then it is advisable to use these to secure to the surface.

6. connect antenna cable to the antenna and then to the terminal

Applications

TRANSPORTATION VESSELS RAILSMALL AIRCRAFT

Beam Antenna RST701 / 703 / 704 / 719

RST701

RST719 (TSO Approved)

RST703

RST704 (TSO Approved)

For more information on Iridium Antenna Guidelines visit our website at www.beamcommunications.com/antennainstallationguide

Vehicle Antenna Installation

The ideal position for any vehicle-mounted

application is to capitalise on the greatest ground

plane from the surface of the vehicle.

Marine Antenna Installation

The antenna must be installed without obstruction of

other instruments or structures.

The antenna must not be positioned within range of

radar equipment or other RF interference.

Fixed Site Installation

The antenna must be installed without obstruction of

other buildings, chimneys or other structures.

Consideration should also be given to the

surrounding environments such as large trees,

mountains or other buildings.

Preferred Antenna Location

USRMAN004202 - Antenna Instructions

For more information on Iridium Antenna Guidelines visit our website at www.beamcommunications.com/antennainstallationguide

Installation Guidelines

To ensure maximum performance of the antenna system and to maximise

availability and reliability of service the antenna must;

• have a clear line of site to the sky

• be clear and free of obstructions

• be clear of metal objects

• be located away from other transmitting devices

• be securely affixed in location

• not be located indoors

• be installed in conjunction with a certified cable

Installing Antenna Cables

When installing antenna cables, follow these guidelines:

• Route and restrain cables to prevent them from vibrating or moving under normal conditions,

which could result in damage to the antenna or the coaxial cable connections.

• Wherever the cables contact structures, protect the cables from chafing or abrasion. If a cable needs

to be bent, avoid kinking it, and ensure that each bend radius follows the cable supplier limits.

• Use coaxial sealant, shrink-wrap tubing, electrical tape, or another suitable product to seal all cable

connections appropriately to prevent moisture and corrosion damage from weather exposure.

• Mount all antennas vertically and clear of nearby metal obstructions

• Minimize horizontal obstructions as much as possible because

they can create areas of poor system coverage.

• To minimize the loss of radio signal from the antenna to the terminal, the specific coaxial cable system

between the antenna and the other component should be less than 3db including connector loss.

Installation Options

The antenna system is suitable for marine, vehicle and fixed applications and is designed to meet Iridium

System performance requirements when installed according to the instructions in this guide.

The following figure shows typical Installations:

Antenna installation is critical for optimum performance of your Iridium service.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Beam Antenne Handbücher

Beam

Beam RST220 Bedienungsanleitung

Beam

Beam RST720 Bedienungsanleitung

Beam

Beam RST215 Bedienungsanleitung

Beam

Beam RST202 Bedienungsanleitung

Beam

Beam RST210 Bedienungsanleitung

Beam

Beam ISD700 Bedienungsanleitung

Beam

Beam Iridium RST706B Bedienungsanleitung

Beam

Beam ISD710 Bedienungsanleitung

Beam

Beam ISD710 Bedienungsanleitung

Beam

Beam RST703 Bedienungsanleitung

Beam

Beam RST710 Bedienungsanleitung

Beam

Beam RST715 Bedienungsanleitung

Beam

Beam Iridium Bedienungsanleitung

Beam

Beam RST720 Bedienungsanleitung

Beam

Beam MG200-VAB Bedienungsanleitung

Beam

Beam RST715 Bedienungsanleitung

Beam

Beam RST705 Bedienungsanleitung

Beam

Beam RST700 Bedienungsanleitung

Beam

Beam RST740 Bedienungsanleitung

Beam

Beam RST710 Bedienungsanleitung

Beam

Beam RST710 Bedienungsanleitung

Beam

Beam RST714 Bedienungsanleitung

Beam

Beam RST714B Bedienungsanleitung

Beam

Beam RST706 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

IWCS

IWCS iriBelt II Einrichtungshandbuch