Becker Online Pro 7800 Bedienungsanleitung

Subject to errors and technical changes 31 Copyright by Becker GmbH, D-76303 Karlsbad

Installation Guide

1. Contents

2. Symbols used in the Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

3. Safety and Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4. Connection schematic for the OnlinePro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5. Installation of the GPS/GSM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

6. Installation of the hands-free microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

7. Installation of the GSM/GPS Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

8. Connection of the reverse signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

9. Connection of the speed signal (GAL) from the speedometer/ tachometer . . . . . . . . . . . . . . 43

10. Installation/ Removal of the OnlinePro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

11. Initial operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

12. Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

13. Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

14. Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

15. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Subject to errors or technical changes 32 Copyright by Becker GmbH, D-76303 Karlsbad

Installation Guide

2. Symbols used in the Installation Guide

Gdenotes instructions which are important for your safety and the safety of others.

denotes instructions which are important for the installation and function of the unit.

3. Safety and Installation Instructions

The OnlinePro should only be installed by trained personnel.

• Disconnect the vehicle battery before installation of the unit.

GNote the safety instructions of the vehicle manufacturer (airbags, immobilisers etc.).

• Ensure that leads are installed in such a manner that they cannot be pinched, bent or pulled out.

• Before installation, park the vehicle in a safe and level place and remove the ignition key.

• If using branch connections, it is important to note the relevant cable section.

Subject to errors and technical changes 33 Copyright by Becker GmbH, D-76303 Karlsbad

Installation Guide

4. Connection schematic for the OnlinePro

Note: Connection options are described in detail on page 57.

Speed signal antenna

Radio

CD changer

Optional

Earphone

Optional

OnlinePro

GSM

Antenna

GPS

GPS/GSM Box Sound system /

loudspeaker

Hands-free

microphone

Reverse signal Power supply

Subject to errors or technical changes 34 Copyright by Becker GmbH, D-76303 Karlsbad

Installation Guide

5. Installation of the GPS/GSM antenna

The antenna delivered with the system is a two-piece combination

GSM/GPS antenna. The combination GSM/GPS antenna is a glass-

adhesive antenna; i.e. no leads must be run from the outside to the

vehicle interior.

The GSM/GPS combination antenna consists of an internal unit Aand

an external unit B. To ensure correct function, the two units must be

installed as described below: Attached to the internal unit Ais a 3-metre

long cable Cwith the combined GSM/GPS plugs. The connecting cable

is connected to the GSM/GPS Box with the GSM/GPS plugs. If more

than 3 metres of cable are required, the cable can be extended with the

optionally available extension cable (Stock No. 1380311). The antenna

Dcan be loosened Fto adjust the angle Eby twisting the antenna. After

loosening and adjusting, the antenna Dmust be screwed on hand-tight.

)The angle of the antenna to the vehicle has an influence on

the antenna’s transmission and reception.

If reception is still unsatisfactory after installation, the

angle of the antenna to the vehicle can be adjusted to

optimise reception. In most cases, best results are achieved

with the antenna in a vertical position.

Windscreen or rear window

Subject to errors and technical changes 35 Copyright by Becker GmbH, D-76303 Karlsbad

Installation Guide

Installation of the GSM/GPS Antenna

GThe antenna is to be affixed in such a manner that it cannot detach in the event of a collision or sudden

braking.

)The antenna can only be installed under a non-metallised windscreen or rear window.

The installation of the GSM/GPS antenna on sharply angled windows (i.e. side windows or rear window in

estate cars/ stations wagons) is not recommended as satisfactory GPS reception cannot be ensured.

(1)

Rear window

Possible antenna positioning

Subject to errors or technical changes 36 Copyright by Becker GmbH, D-76303 Karlsbad

Installation Guide

a. Determine installation position (1) (rear window, windscreen)

)The antenna must not be affixed over the heating wires of heated windscreens or rear windows.

Windows with metal layered plastic window tinting are not suitable.

Take the windscreen-wiper range into account when positioning the antenna.

The glass surface to which the antenna must adhere, may be slightly curved.

When selecting position for installation, please bear in mind the possibility of cable extension.

Windscreen/Rear window

Slot faces upwards.

(2)

(A)

(B)

Protective paper

Subject to errors and technical changes 37 Copyright by Becker GmbH, D-76303 Karlsbad

Installation Guide

GThe driver’s field of vision must not be obstructed.

GClean adhesion surfaces (inside and outside) with the enclosed cleaning cloth.

After cleaning, wait until the cleaned surfaces have dried.

b. Completely pull off protective paper from the adhesive surface (the square piece as well) (2). Caution: The

adhesive part is now exposed.

First adhere the external unit (A) with the slot at the top to the glass by firmly pressing (approx. 3-5 seconds)

around the circumference of the external unit base.

Subsequently, affix internal unit (B) to the inside of the window, once again by pressing on the housing of the unit

for approx. 3-5 seconds, with the circular area centred in the middle of the outside unit (centre point = centring

axis).

Depending upon the amount of space, the position of the internal unit can be turned on this centring axis before

being directly affixed.

)The ideal adhesion temperature is between +15 °C and +25 °C.

The adhesive foil will adhere immediately to the adhesion surface and cannot be repositioned. It is not possible

to reuse the adhesive foil.

c. Run connecting cable to the installation position of the GSM/GPS Box.

Subject to errors or technical changes 38 Copyright by Becker GmbH, D-76303 Karlsbad

Installation Guide

6. Installation of the hands-free microphone

The hands-free microphone should be placed in the vehicle to allow optimal recognition of the speaker’s voice. Possible

positions in the vehicle for the microphone can be seen in the following diagram.

)The installation position should be as far away from the loudspeakers as possible. If problems occur, different

positions should be tested. In order to pick up as little background noise as possible, the microphone has a

narrow pick-up angle and must consequently be directed towards the driver.

Affixing the hands-free microphone to a flat and smooth surface can be accomplished with the adhesive strip E(Clean

adhesion surfaces). If the microphone is to be affixed to a rough or uneven surface, the screw-on plate Gshould be affixed

first with the screw F(To avoid risk of damage, please pay attention to screw length). Subsequently, affix the microphone

to the screw-on plate Gwith the adhesive strip E. The connection of the hands-free microphones takes place in socket C

of the OnlinePro.

A: Optimal installation position

B: Alternative installation position

C: Less suitable installation position

D: Speaking direction on microphone

E: Adhesive strip for affixing to smooth surfaces

F: Screw for fastening the screw-on plate

G: Screw-on plate for affixing to rough or uneven surfaces.

Subject to errors and technical changes 39 Copyright by Becker GmbH, D-76303 Karlsbad

Installation Guide

Install the lead in such a manner that it cannot be pinched, bent or pulled out.

Connection of the hands-free microphone to the OnlinePro

a. Connection without CD changer

For connection of the hands-free microphone to an OnlinePro without CD changer, the enclosed blue socket must

be connected as described below. Before connection, remove protective cap Afrom both contacts.

b. Connection with CD changer

For connection of the hands-free microphone to an OnlinePro with CD changer, the enclosed blue socket must

be connected with the two leads as described below. Before connection, remove protective cap Afrom both

contacts.

)Once the contacts are inserted into the blue plug housing, a special tool is required to remove them.

Connection of the blue plug housing

Socket C

Socket C3

Pin Colour Function

13 White NF

14 Yellow Earth

Subject to errors or technical changes 40 Copyright by Becker GmbH, D-76303 Karlsbad

Installation Guide

7. Installation of the GSM/GPS Box

The connectors for the combination GSM/GPS antenna, the optional operating headset and connecting cable to the

OnlinePro are to be connected to the GSM/GPS Box. The SIM card necessary for activation and operation of the telephone

must be inserted into the card-holding slot.

The GSM/GPS Box can be installed in the glove compartment, for example. However, an installation position allowing a

maximum possible distance from the Online Pro should be selected.

On the housing of the GSM/GPS Box, there are two Velcro strips Ffor attachment.

Install the lead in such a manner that it cannot be pinched, bent or pulled out.

The GSM/GPS Box should be installed in such a way that the SIM card inserted into the SIM card holder can be taken out

without having to remove the GSM/GPS Box.

Side view,

left

GSM/GPS Box Side view,

right

A: Retaining cover over SIM card holder

B: Connection socket for connection

cable to OnlinePro

C: Connection for optional

operating headset

D: GPS antenna connection

E: GSM antenna connection

F: Velcro strip for attachment

Andere Handbücher für Online Pro 7800

Inhaltsverzeichnis

Andere Becker Autoradiosystem Handbücher

Becker

Becker Online Pro 7800 Technisches Handbuch

Becker

Becker DTM High Speed 7910 Bedienungsanleitung

Becker

Becker Traffic Pro 4720 Bedienungsanleitung

Becker

Becker DTM High Speed 7910 Bedienungsanleitung

Becker

Becker Traffic Pro 7949 Bedienungsanleitung

Becker

Becker Indianapolis Pro 7950 Bedienungsanleitung

Becker

Becker Grand Prix 7990 Bedienungsanleitung

Becker

Becker IP-BKR2 Bedienungsanleitung

Becker

Becker Traffic Pro High Speed 7820 Bedienungsanleitung

Becker

Becker Traffic Pro 7949 Bedienungsanleitung

Becker

Becker Mexico CC4325 Bedienungsanleitung

Becker

Becker Audio 30 Export 3301 Bedienungsanleitung

Becker

Becker Indianapolis 7920 Bedienungsanleitung

Becker

Becker Traffic Pro 7945 Bedienungsanleitung

Becker

Becker Traffic Pro 4720 Bedienungsanleitung

Becker

Becker Indianapolis 7920 Bedienungsanleitung

Becker

Becker DTM High Speed 7910 Bedienungsanleitung

Becker

Becker Traffic Pro 4720 Bedienungsanleitung

Becker

Becker INDIANAPOLIS PRO Bedienungsanleitung

Becker

Becker DTM Bedienungsanleitung

Becker

Becker USB-BKR Bedienungsanleitung

Becker

Becker Cascade Bedienungsanleitung

Becker

Becker Cascade Bedienungsanleitung

Becker

Becker Mexico Pro 7930 Bedienungsanleitung

Beliebte Autoradiosystem Handbücher anderer Marken

JL Audio

JL Audio Stealthbox SB-CAN-G2MVX3D/10TW3 Bedienungsanleitung

Clarion

Clarion PU-9836A Bedienungsanleitung

Sony

Sony MEX-BT5750U Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AR0M Bedienungsanleitung

Sony

Sony RM-X7BT Bedienungsanleitung

Insignia

Insignia NS-HD5113 Bedienungsanleitung

Clarion

Clarion BTD3341 Bedienungsanleitung

USA SPECS

USA SPECS PA11-VW6 Bedienungsanleitung

Sony

Sony MEX-N4380BT Bedienungsanleitung

Kenwood

Kenwood KCD-BT6544U/UY Bedienungsanleitung

JVC

JVC KD-DB912BT Bedienungsanleitung

Philips

Philips CSQ405/98 Bedienungsanleitung

Alpine

Alpine TDM-7544 Bedienungsanleitung

Autotek

Autotek TransAm TA 1400 Bedienungsanleitung

Clarion

Clarion PN-3124N-A Bedienungsanleitung

Denso TEN

Denso TEN FT0108A Bedienungsanleitung

Pyle

Pyle PLD57MU Bedienungsanleitung

Harman

Harman Chrysler Radio Navigation System RB4 Bedienungsanleitung