Beckhoff M1400 Leitfaden
M1400 Parallel Input /Output Beckhoff II/O-System
Date : 26.7.94 Version : 2.0 Page 1 of 16
M1400 Parallel Input / Output
Technical Documentation
Eiserstraße 5 phone 05246/709-0
33415 Verl fax 05246/70980
M1400 Parallel Input / Output Beckhoff II/O-System
Page 2 of 16 Version : 2.0 Date : 26.7.94
Table of Contents
1. Function Description Hardware....................................................3
2. Function Description Software......................................................5
3. Technical Data.................................................................................6
4. Installation.......................................................................................7
5. Table of Connections....................................................................11
M1400 Parallel Input /Output Beckhoff II/O-System
Date : 26.7.94 Version : 2.0 Page 3 of 16
1. Function Description Hardware
M1400
About the Hardware
The parallel module M1400 is an input / output module used in the II/O system. There are 32
Standard 24 V inputs / outputs, which achieve 4 ports of 8 bit each.
These 4 ports ( D0..D3 ) correspond to the data bytes in the FO transmissions protocol and
according to the way they are to be used, they can be configured as input or output.
Each input / output has an LED, that indicates the current state. Furthermore there are three
LED’s installed used for diagnosis of the II/O fibre optical ring:
LD1 The green ’CYCLE’ LED is switched on by each start bit of a telegram and is
switched off again by the stop bit.
LD2 The red ’ERROR’LED is switched on after the recognition of a bad telegram (checksum,
frame). After a sequence of three correct telegrams (checksum, frame) were processed it
is switched off again.
LD3 The green LED ’WATCHDOG’is switched on by a valid writing telegram with matching
address. If no telegram with the properties defined above is recognised for the next
100 ms a special unit of the module switches off all outputs.
In case an error is detected, all outputs are reset.
M1400 Parallel Input / Output Beckhoff II/O-System
Page 4 of 16 Version : 2.0 Date : 26.7.94
Basic Circuit Diagram
M1400 Parallel Input /Output Beckhoff II/O-System
Date : 26.7.94 Version : 2.0 Page 5 of 16
2. Function Description Software
M1400 Parallel Input / Output Beckhoff II/O-System
Page 6 of 16 Version : 2.0 Date : 26.7.94
3. Technical Data
Inputs / Outputs 32, can be configured for each port;
LED shows state of all inputs / outputs
input specifications 24 VDC, 10 mA, digital filter
input switching voltages 0 - 8V = LOW
15 - 24V = HIGH
input delay 0,7 ms RC network
6,8 ms input latch
Output specifications 24 VDC, max. 500 mA, short circuit proof
Output check watchdog system 100 ms
Connections can be connected for 16 I/O; +,-,signal
Data connection fibre optic II/O system
transmission rate 2,5 MBaud, 25 µs for 32 Bit
Supply Voltage 24 VDC (± 10%)
Input Current 0,1 A (without load and input currents)
Cartridge closed, can be installed to cartridge carrier
according to DIN EN 50022, 50035
Size (B * W * D) 270 * 76 * 68 mm
Weight about 1100 g
Working Temperature ±0..+55 øC
Storage Temperature -20..+70 øC
M1400 Parallel Input /Output Beckhoff II/O-System
Date : 26.7.94 Version : 2.0 Page 7 of 16
4. Installation
Montage
The M1400 is connected to the fibre optic ring using fibre optic connections (Toshiba). The
maximum length of the FO cable, leading to the neighbouring boxes, should not be more then
600m for glass fibre or 45 meters for other fibres. These values are only valid if for bending
the cable a radius of at least 30 mm is used. If there are no glass fibres used, no special tools
are needed for installation of the plugs.
Common actors and sensor are connected directly to the inputs / outputs (using"+,-,signal" ).
The M1400 is installed at the machine or simply by installing it to a cartridge carrier
according to DIN EN 50022 or DIN EN 50035.
Configuration
Each I/Oport of the M1400 can be configured as input or as output. This does not dependent
on the configuration of the other ports. There are DIP switches under the XILINX board of the
M1400. In order to change the state of the switches the module’s cartridge has to be opened.
The DIP switches are assigned as follows:
switch 1 => port D0
switch 2 => port D1
switch 3 => port D2
switch 4 => port D3
It depends on the state of the switch whether a port is an output or an input :
’ON’ => port is output
’OFF’=> port is input
ATTENTION:
Configuring a port as input ( switch "OFF") all of the eight output controller
ICs of the port concerned have to be removed.
If the ICs are not removed the port is not functional as input, but the module
remains undamaged.
M1400 Parallel Input / Output Beckhoff II/O-System
Page 8 of 16 Version : 2.0 Date : 26.7.94
View under the M1400 XILINX board
The following module configuration is possible by setting jumpers 1 to 3 :
Jumper 1 Watchdog on / off
for Port D0 and D1
If this jumper is set the ’Watchdog’function is switched off.
This means if an error is detected the outputs set of Port D0
and D1 are not switched off.
Jumper 2 Watchdog on / off
for Port D2 und D3
If this jumper is set the ’Watchdog’function is switched off.
This means if an error is detected the outputs set of Port D2
and D3 are not switched off.
Jumper 3 Latch on / off
standard configuration is jumper ’set’
input are latched in intervals of 6,8 ms
otherwise inputs are latched permanently
M1400 Parallel Input /Output Beckhoff II/O-System
Date : 26.7.94 Version : 2.0 Page 9 of 16
The following modul configuration is possible by setting jumpers 4 to 7 :
Fast Inputs M1400 (Interrupt Inputs)
Jumper 4 Fast input II3 :
If jumper connection betwenn port D0.3 and XILINX II3 is
established Fast input is activated
Jumper 5 Fast input II2 :
If jumper connection betwenn port D0.2 and XILINX II3 is
established Fast input is activated
Jumper 6 Fast input II1 :
If jumper connection betwenn port D0.1 and XILINX II3 is
established Fast input is activated
Jumper 7 Fast input II0 :
If jumper connection betwenn port D0.0 and XILINX II3 is
established Fast input is activated
Power Supply
There are the following connections for power Supply :
(1) two pole plug connection for the controller (X10 Pin1+2)
(2) two pole plug connection for outputs (X20 and X30 Pin1+2)
( 16 outputs )
(3) two pole plug connection for inputs (X21 and X31 Pin1+2)
(16 inputs)
(4) two pole plug connection for ground (X22 and X32 Pin1+2)
M1400 Parallel Input / Output Beckhoff II/O-System
Page 10 of 16 Version : 2.0 Date : 26.7.94
Inhaltsverzeichnis
Andere Beckhoff Steuereinheit Handbücher
Beckhoff
Beckhoff AX2090-BW5 Series Bedienerhandbuch
Beckhoff
Beckhoff EP7041 Series Bedienerhandbuch
Beckhoff
Beckhoff KM10 Series Bedienerhandbuch
Beckhoff
Beckhoff AX2090-TS50-3000 Bedienerhandbuch
Beckhoff
Beckhoff AX8000 Bedienungsanleitung
Beckhoff
Beckhoff KM6551 Bedienerhandbuch
Beckhoff
Beckhoff EPP3174 Bedienerhandbuch
Beckhoff
Beckhoff EP7211-0034 Bedienerhandbuch
Beckhoff
Beckhoff TF6120 Bedienungsanleitung
Beckhoff
Beckhoff KM2042 Bedienerhandbuch
Beckhoff
Beckhoff KS2502 Bedienerhandbuch
Beckhoff
Beckhoff PS9031-4820-0001 Bedienerhandbuch
Beckhoff
Beckhoff BK5200 Leitfaden
Beckhoff
Beckhoff CX2500-0061 Bedienungsanleitung
Beckhoff
Beckhoff EP3204 Bedienerhandbuch
Beckhoff
Beckhoff EPP3744 041 Series Bedienungsanleitung
Beckhoff
Beckhoff CX2550-0020 Bedienungsanleitung
Beckhoff
Beckhoff EJ7211-0010 Bedienerhandbuch
Beckhoff
Beckhoff M310 Bedienungsanleitung
Beckhoff
Beckhoff AX5721 Leitfaden
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
