Beckhoff CP62 Series Bedienungsanleitung

Installation and Operating instructions for

Built-in Panel PC CP62xx

Version: 1.7

Date: 2007-10-19

General Notes

Table of contents

General Notes 3

Notes on the documentation 3

Liability conditions 3

Description of safety symbols 3

Basic safety measures 4

Operator's obligation to exercise diligence 5

Operator requirements 5

Product Description 6

Appropriate Use 6

Interfaces 6

Fieldbus 6

Serial interface 6

DVI (Digital Visual Interface) 6

USB-Interfaces 6

Network connection 6

Power supply 6

Additional plug-in cards (optional) 6

Ground connection 6

Access to the drives 6

Installation Instructions 7

Transport and Unpacking 7

Transport 7

Unpacking 7

Installation of the PC in the control cabinet 8

Earthing measures 8

Assembly dimensions 9

Mounting of the Panel-PC 10

Power Supply Connection 11

Pin assignment of the connector 11

Fitting the cable 12

Material for assembling the connectors 12

Assembling the connectors 12

Connecting Power Supply 13

Cable Cross Sections 13

PC_ON, Power-Status, UPS output 13

Wiring diagram 14

Connecting devices 14

Connecting cables 14

Check voltage rating and connect 15

Operating Instructions 16

Switching the Industrial PC on and off 16

First switching on and driver installation 16

Operation 16

Keyboard codes 17

Servicing and maintenance 19

Cleaning the Industrial PC 19

Replacing the battery on the motherboard 19

Servicing 19

Replacing the fluorescent lamps in the display 19

Lamp sets 20

Emergency procedures 20

Shutting down 20

Disposal 20

CP62xx 1

General Notes

UPS Software Components (optional) 21

Installation on the PC 21

Help files 21

Troubleshooting 22

Fault correction 22

Service and Support 23

Beckhoff's branch offices and representatives 23

Beckhoff headquarters 23

Beckhoff Support 23

Beckhoff Service 23

Appendix 24

Technical data 24

Approvals 24

FCC: Federal Communications Commission Radio Frequency Interference

Statement 24

FCC: Canadian Notice 24

2CP62xx

General Notes

Notes on the documentation

This description is only intended for the use of trained specialists in control

and automation engineering who are familiar with the applicable national

standards. It is essential that the following notes and explanations are

followed when installing and commissioning these components.

Liability conditions

The responsible staff must ensure that the application or use of the

products described satisfy all the requirements for safety, including all the

relevant laws, regulations, guidelines and standards.

The documentation has been prepared with care. The products described

are, however, constantly under development. For this reason, the

documentation may not always be have been fully checked for consistency

with the performance data, standards or other characteristics described.

None of the statements in this manual represent a guarantee for as set out

in § 443 of the German Civil Code or a statement about the assumed use

according to the contract as set out in § 434 para. 1 clause 1 no. 1 of the

German Civil Code. In the event that it contains technical or editorial errors,

we retain the right to make alterations at any time and without warning. No

claims for the modification of products that have already been supplied

may be made on the basis of the data, diagrams and descriptions in this

documentation.

party use of this publication, whether in whole or in part, without the written

permission of Beckhoff Automation GmbH, is forbidden.

Description of safety symbols

The following safety symbols are used in this operating manual. They are

intended to alert the reader to the associated safety instructions.

Danger

This symbol is intended to highlight risks for the life or health of personnel.

Warning

This symbol is intended to highlight risks for equipment, materials or the

environment.

Note

This symbol indicates information that contributes to better understanding.

CP62xx 3

General Notes

Basic safety measures

Only switch the PC off after

closing the software

Before the Industrial PC is switched off, software that is running must

be properly closed.

Otherwise it is possible that data on the hard disk is lost. Please read the

section Switching the Industrial PC on and off.

Warning

Switch off all parts of the equipment, then uncouple the fieldbus!

Before opening the housing of the PC, and whenever the PC is being used

for purposes other than plant control, such as during functional tests

following repair, all parts of the equipment must first be switched off, after

which the Industrial PC can be uncoupled from the plant.

Pulling out the fieldbus connection plug uncouples the PC (optional).

Items of equipment that have been switched off must be secured against

being switched on again.

The Industrial PC’s power supply unit must be supplied with

24VDC.

Danger

Do not open the power supply unit while voltage is applied!

The supply voltage must be switched off before the power supply unit

housing is opened.

Do not exchange any parts when under power!

When components are being fitted or removed, the supply voltage must be

switched off.

Fitting work on the Industrial PC can result in damage:

• If metal objects such as screws or tools fall onto operating circuit

boards.

• If connecting cables internal to the PC are removed or inserted

during operation.

• If plug-in cards are removed or inserted when the PC is switched

on.

Danger

Displays used for the control panel’s LC-display are operated with a

voltage of up to 1000 V, depending on type. For that reason:

The supply voltage must be disconnected before the housing of the

Control Panel is opened.

4CP62xx

General Notes

Operator's obligation to exercise diligence

The operator must ensure that

• the Industrial PC is only used for its intended purpose (see Product

Description section);

• the Industrial PC is only operated in a sound condition and in

working order;

• the instruction manual is in good condition and complete, and

always available for reference at the place of installation of the

Industrial PC;

• the Industrial PC is operated, maintained and repaired only by

suitably qualified and authorized personnel.

• the personnel is instructed regularly about relevant occupational

safety and environmental protection aspects, and is familiar with

the operating manual and in particular the safety notes contained

herein.

• none of the safety and warning notes attached to the Industrial PC

are removed, and all notes remain legible.

National regulations

depending on the machine

type

Depending on the type of machine and plant in which the Industrial PC is

used, national regulations governing the controllers of such machines will

apply, and must be observed by the operator. These regulations cover,

amongst other things, the intervals between inspections of the controller.

The operator must initiate such inspections in good time.

Warning

Only trained persons may open the Industrial PC housing!

The operator is responsible for ensuring that only trained electrical staff

opens the housing of the Industrial PC.

Procedure in the event of a

fault

In the event of faults at the Industrial PC, the list in the section

Troubleshooting can be used to determine the measures to be taken.

Operator requirements

Read the operating

instructions

Anyone who uses the Industrial PC must have read these operating

instructions.

Software knowledge Every user must be familiar with all the functions of the software installed

on the Industrial PC to which he has access.

CP62xx 5

Product Description

Appropriate Use

The CP62xx Build-in Panel PC is designed for industrial application in

machine and plant engineering. A steel plate housing with aluminum front

contains a TFT display, touch screen/ pad (optional) and a PC keyboard

(optional). The Industrial PC is installed in the front of control cabinets.

Do not use the Build-in

Panel PC in areas of

explosive hazard

The Build-in Panel PC must not be used where there is a risk of

explosion.

Interfaces

Interfaces to the Build-in

Panel PC

Fieldbus

The Industrial PC has one fieldbus-interface, which is brought to a 9 pin

SUB-D plug connector.

Serial interface

RS 232

COM1

The Industrial PC has one serial interfaces, COM1, using the type RS232,

which are each brought to a 9 pin SUB-D plug connector.

DVI (Digital Visual Interface)

DVI out The DVI connection is used for transferring the video signal. DVI-I standard

is supported.

USB-Interfaces

USB out The four USB interfaces are used for connecting peripheral devices with

USB connection. USB2.0 standard is supported.

Network connection

LAN1 The RJ-45 connector allows the PC to be connected to a 10/100BASE-T

Local Area Network (LAN).

LAN2 The RJ-45 connector allows the PC to be connected to a 100/1000BASE-T

Local Area Network (LAN).

Power supply

Power The power supply for the Industrial PC is established via the

socket.

Additional plug-in cards (optional)

Type plate There is a type plate on the top of the Industrial PC which provides

information about the hardware configuration of the Industrial PC at the

time it was supplied.

Ground connection

Ground connection The Control Panel is grounded via the stud bolt.

Access to the drives

Access to hard-disk, CF-

Card and battery

After solving the knurled screw, the cap can be removed and allows access

to hard disk, battery and CF-Card.

Knurled screw

6CP62xx

Installation Instructions

Transport and Unpacking

The specified storage conditions must be observed (see chapter Technical

data).

Transport

Despite the robust design of the unit, the components are sensitive to

strong vibrations and impacts. During transport, your Industrial PC should

therefore be protected from excessive mechanical stress. Therefore,

please use the original packaging.

Warning

Danger of damage to the unit!

If the device is transported in cold weather or is exposed to extreme

variations in temperature, make sure that moisture (condensation) does not

form on or inside the device.

Prior to operation, the unit must be allowed to slowly adjust to room

temperature. Should condensation occur, a delay time of approximately 12

hours must be allowed before the unit is switched on.

Unpacking

Proceed as follows to unpack the unit:

1.Remove packaging.

2.Do not discard the original packaging. Keep it for future relocation.

3.Check the delivery for completeness by comparing it with your order.

4.Please keep the associated paperwork. It contains important

information for handling the unit.

5.Check the contents for visible shipping damage.

6.If you notice any shipping damage or inconsistencies between the

contents and your order, you should notify Beckhoff Service.

CP62xx 7

Installation Instructions

Installation of the PC in the control cabinet

The Built-in Panel PC CP62xx is designed for mounting in control cabinets

in machine and plant engineering applications.

The ambient conditions specified for operation must be observed (see the

section on Technical data).

Preparation of the control

cabinet

The control cabinet wall must be prepared with the required mounting

opening for the computer unit according to the PC's dimensions.

Note

When the unit is installed in an enclosure, adequate space for

ventilation and for opening the PC must be provided.

The clearance above and below the housing must be at least 50 mm

in order to ensure adequate ventilation of the PC.

Please note the following points during installation of the PC:

• Position the PC in such a way that reflections on the screen are

avoided as far as possible.

• Use the position of the screen as a guide for the correct installation

height; it should be optimally visible for the user at all times.

• The PC should not be exposed to direct sunlight.

• When the unit is in its mounting position, the ventilation openings must

not be obstructed.

Warning

Extreme environmental conditions should be avoided as far as

possible. Protect the rear of your PC from dust, humidity and heat.

The ventilation slots of the PC must not be covered.

Installation in a control

cabinet wall

Proceed as follows:

1. Insert the PC at the intended control cabinet wall position and protect it

from falling out, prior to final mounting.

2. Release the clamping levers with a No. 3 Allen key, turn the clamping

levers to the side through 90° and retighten the screws.

Earthing measures

Earthing connections dissipate interference from external power supply

cables, signal cables or cables to peripheral equipment.

Establish a low-impedance connection from the earthing point on the PC

housing to the central earthing point on the control cabinet wall, in which

the computer is being installed.

8CP62xx

Andere Handbücher für CP62 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Beckhoff Industrie-PC Handbücher

Beckhoff

Beckhoff C6032 Bedienungsanleitung

Beckhoff

Beckhoff C6930 Bedienungsanleitung

Beckhoff

Beckhoff C33-0060 Series Bedienungsanleitung

Beckhoff

Beckhoff EP6224 Bedienerhandbuch

Beckhoff

Beckhoff CX8010 Bedienerhandbuch

Beckhoff

Beckhoff C5 Series Bedienungsanleitung

Beckhoff

Beckhoff CX20 0 Series Bedienungsanleitung

Beckhoff

Beckhoff MIC3200 Bedienungsanleitung

Beckhoff

Beckhoff CX5120 Bedienungsanleitung

Beckhoff

Beckhoff C6915 Bedienungsanleitung

Beckhoff

Beckhoff C6032 Bedienungsanleitung

Beckhoff

Beckhoff CX2000 Series Bedienungsanleitung

Beckhoff

Beckhoff C6525 Bedienungsanleitung

Beckhoff

Beckhoff C61 Series Bedienungsanleitung

Beckhoff

Beckhoff C6027 Bedienungsanleitung

Beckhoff

Beckhoff C6240-1007-0060 Bedienungsanleitung

Beckhoff

Beckhoff C6017-0010 Bedienungsanleitung

Beckhoff

Beckhoff C5210 Bedienungsanleitung

Beckhoff

Beckhoff C5102-0060 Bedienungsanleitung

Beckhoff

Beckhoff C6032 Bedienungsanleitung

Beckhoff

Beckhoff C7015 Bedienungsanleitung

Beckhoff

Beckhoff MIC3100 Bedienungsanleitung

Beckhoff

Beckhoff TF5200 Bedienungsanleitung

Beckhoff

Beckhoff C6250-0060 Bedienungsanleitung

Beliebte Industrie-PC Handbücher anderer Marken

Chipsee

Chipsee PPC-A72-101 Bedienungsanleitung

Advantech

Advantech UNO-2184G Bedienungsanleitung

MSI

MSI MS-9A76 Bedienungsanleitung

Stackrack

Stackrack THOR200 Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-682C Series Bedienungsanleitung

Nodka

Nodka eBOX-3000-ETC Bedienungsanleitung

Siemens

Siemens SIMATIC IPC627E Bedienungsanleitung

MSI

MSI MS-9A89 Bedienungsanleitung

Artila

Artila Matrix-516 Bedienungsanleitung

Siemens

Siemens SIMATIC Rack PC 840 V2 Bedienungsanleitung

Advantech

Advantech IPPC-6152A Bedienungsanleitung

Dell

Dell Embedded Box PC 5000 Bedienungsanleitung

IBASE Technology

IBASE Technology ASB200-918 Series Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M90q Betriebsanleitung

IXXAT

IXXAT Econ 100 Bedienungsanleitung

Kontron

Kontron KBox A-151-TGL Bedienungsanleitung

AXIOMTEK

AXIOMTEK ICO500-518 Series Bedienungsanleitung

JLT

JLT 1214N Bedienungsanleitung