Beckhoff ELX3152 Bedienungsanleitung

Operating manual | EN

ELX3152 and ELX3158

Two- and eight-channel analog input terminals, 0/4 … 20 mA,

single ended, 16 Bit, Ex i

2020-10-08 | Version: 2.0.0

Table of contents

ELX3152 and ELX3158 3Version: 2.0.0

Table of contents

1 Foreword ....................................................................................................................................................5

1.1 Notes on the documentation..............................................................................................................5

1.2 Safety instructions .............................................................................................................................6

1.3 Documentation Issue Status..............................................................................................................7

1.4 Marking of ELX terminals ..................................................................................................................8

2 Product overview.....................................................................................................................................12

2.1 ELX3152 - Introduction....................................................................................................................12

2.2 ELX3158 - Introduction....................................................................................................................13

2.3 Technical data .................................................................................................................................14

2.4 Intended use....................................................................................................................................15

3 Mounting and wiring................................................................................................................................16

3.1 Special conditions of use for ELX terminals ....................................................................................16

3.2 Installation notes for ELX terminals .................................................................................................16

3.3 Arrangement of ELX terminals within a bus terminal block .............................................................18

3.4 Installation position and minimum distances ...................................................................................21

3.5 Installation of ELX terminals on mounting rails................................................................................22

3.6 Connection ......................................................................................................................................23

3.6.1 Connection system .......................................................................................................... 23

3.6.2 Wiring............................................................................................................................... 24

3.6.3 Proper line connection ..................................................................................................... 26

3.6.4 Shielding and potential separation................................................................................... 26

3.6.5 ELX3152 - Contact assignment ....................................................................................... 27

3.6.6 ELX3158 - Contact assignment ....................................................................................... 29

4 Appendix ..................................................................................................................................................31

4.1 EtherCAT AL Status Codes.............................................................................................................31

4.2 UL notice .........................................................................................................................................31

4.3 FM notice.........................................................................................................................................32

4.4 Support and Service ........................................................................................................................33

Table of contents

ELX3152 and ELX31584 Version: 2.0.0

Foreword

ELX3152 and ELX3158 5Version: 2.0.0

1 Foreword

1.1 Notes on the documentation

Intended audience

This description is only intended for the use of trained specialists in control and automation engineering who

are familiar with the applicable national standards.

It is essential that the documentation and the following notes and explanations are followed when installing

and commissioning these components.

It is the duty of the technical personnel to use the documentation published at the respective time of each

installation and commissioning.

The responsible staff must ensure that the application or use of the products described satisfy all the

requirements for safety, including all the relevant laws, regulations, guidelines and standards.

Disclaimer

The documentation has been prepared with care. The products described are, however, constantly under

development.

We reserve the right to revise and change the documentation at any time and without prior announcement.

No claims for the modification of products that have already been supplied may be made on the basis of the

data, diagrams and descriptions in this documentation.

Trademarks

Beckhoff®, TwinCAT®, EtherCAT®, EtherCATG®, EtherCATG10®, EtherCATP®, SafetyoverEtherCAT®,

TwinSAFE®, XFC®, XTS® and XPlanar® are registered trademarks of and licensed by Beckhoff Automation

GmbH. Other designations used in this publication may be trademarks whose use by third parties for their

own purposes could violate the rights of the owners.

Patent Pending

The EtherCAT Technology is covered, including but not limited to the following patent applications and

patents: EP1590927, EP1789857, EP1456722, EP2137893, DE102015105702 with corresponding

applications or registrations in various other countries.

EtherCAT® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH,

Germany.

The reproduction, distribution and utilization of this document as well as the communication of its contents to

others without express authorization are prohibited.

patent, utility model or design.

Foreword

ELX3152 and ELX31586 Version: 2.0.0

1.2 Safety instructions

Safety regulations

Please note the following safety instructions and explanations!

Product-specific safety instructions can be found on following pages or in the areas mounting, wiring,

commissioning etc.

Exclusion of liability

All the components are supplied in particular hardware and software configurations appropriate for the

application. Modifications to hardware or software configurations other than those described in the

documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.

Personnel qualification

This description is only intended for trained specialists in control, automation and drive engineering who are

familiar with the applicable national standards.

Description of instructions

In this documentation the following instructions are used.

These instructions must be read carefully and followed without fail!

DANGER

Serious risk of injury!

Failure to follow this safety instruction directly endangers the life and health of persons.

WARNING

Risk of injury!

Failure to follow this safety instruction endangers the life and health of persons.

CAUTION

Personal injuries!

Failure to follow this safety instruction can lead to injuries to persons.

NOTE

Damage to environment/equipment or data loss

Failure to follow this instruction can lead to environmental damage, equipment damage or data loss.

Tip or pointer

This symbol indicates information that contributes to better understanding.

Foreword

ELX3152 and ELX3158 7Version: 2.0.0

1.3 Documentation Issue Status

Version Comment

2.0.0 • ELX3158 added

1.6.0 • FM notice regarding ANSI/ISA EX added

• Chapter Marking of ELX terminals updated

1.5.0 • Contact assignment extended with sensor illustration

• Chapter Arrangement of ELX terminals within a bus terminal block updated

• Chapter Marking of ELX terminals updated

• Technical data updated

1.4.0 • Chapter Arrangement of ELX terminals at the bus terminal updated

1.3.0 • Chapter Installation notes for ELX terminals updated

1.2.0 • Chapter Marking of ELX-Terminals updated

• Technical data updated

1.1.0 • Chapter Marking of ELX-Terminals updated

1.0.0 • Chapter Intended use updated

• Technical data updated

• Mounting and wiring updated

0.2 • Chapter Intended use added

• Mounting and wiring updated

0.1 • First preliminary version

Foreword

ELX3152 and ELX31588 Version: 2.0.0

1.4 Marking of ELX terminals

Name

An ELX terminal has a 15-digit technical designation, composed of

• family key

• type

• software variant

• revision

example family type software variant revision

ELX1052-0000-0001 ELX terminal 1052: two-channel digital input terminal

for NAMUR sensors, Ex i

0000: basic type 0001

ELX9560-0000-0001 ELX terminal 9560: power supply terminal 0000: basic type 0001

Notes

• The elements mentioned above result in the technical designation. ELX1052-0000-0001 is used in

the example below.

• Of these, ELX1052-0000 is the order identifier, commonly called just ELX1052 in the "-0000" revision.

“-0001” is the EtherCAT revision.

• The order identifier is made up of

- family key (ELX)

- type (1052)

- software version (-0000)

• The Revision -0001 shows the technical progress, such as the extension of features with regard to the

EtherCAT communication, and is managed by Beckhoff.

In principle, a device with a higher revision can replace a device with a lower revision, unless specified

otherwise, e.g. in the documentation.

Associated and synonymous with each revision there is usually a description (ESI, EtherCAT Slave

Information) in the form of an XML file, which is available for download from the Beckhoff website.

The revision has been applied to the terminals on the outside, see ELX1052 with date code

3218FMFM, BTN 10000100 and Ex marking.

• The hyphen is omitted in the labeling on the side of the terminal. Example:

Name: ELX1052-0000

Label: ELX1052 0000

• The type, software version and revision are read as decimal numbers, even if they are technically

saved in hexadecimal.

Identification numbers

ELX terminals have two different identification numbers:

• date code (batch number)

•Beckhoff Traceability Number, or BTN for short (as a serial number it clearly identifies each terminal)

Datecode

The date code is an eight-digit number given by Beckhoff and printed on the ELX terminal. The date code

indicates the build version in the delivery state and thus identifies an entire production batch, but does not

distinguish between the terminals in a batch.

Structure of the date code: WWYYFFHH

WW - week of production (calendar week)

YY - year of production

FF - firmware version

HH - hardware version

Example with date code: 02180100:

02 - week of production 02

18 - year of production 2018

01 - firmware version 01

00 - hardware version 00

Foreword

ELX3152 and ELX3158 9Version: 2.0.0

Beckhoff Traceability Number (BTN)

In addition, each ELX terminal has a unique Beckhoff Traceability Number (BTN).

Ex marking

The Ex marking can be found at the top left on the terminal:

II 3 (1) G Ex ec [ia Ga] IIC T4 Gc

II (1) D [Ex ia Da] IIIC

I (M1) [Ex ia Ma] I

IECEx BVS 18.0005X

BVS 18 ATEX E 005 X

Examples

Fig.1: ELX2008-0000 with date code 2519HMHM, BTN 0001f6hd and Ex marking

Foreword

ELX3152 and ELX315810 Version: 2.0.0

Fig.2: ELX9560-0000 with date code 12150000, BTN 000b000 and Ex marking

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Beckhoff Touch-Terminal Handbücher

Beckhoff

Beckhoff EL1918 Bedienungsanleitung

Beckhoff

Beckhoff KL6301-0000 Bedienerhandbuch

Beckhoff

Beckhoff KL3356 Bedienerhandbuch

Beckhoff

Beckhoff KL4414 Bedienerhandbuch

Beckhoff

Beckhoff KL4132 Bedienerhandbuch

Beckhoff

Beckhoff ELX3202 Bedienungsanleitung

Beckhoff

Beckhoff EL1052 Bedienerhandbuch

Beckhoff

Beckhoff KL3403 Series Bedienerhandbuch

Beckhoff

Beckhoff EL72 1 Series Bedienerhandbuch

Beckhoff

Beckhoff KL2904 Bedienungsanleitung

Beckhoff

Beckhoff KL3444 Bedienerhandbuch

Beckhoff

Beckhoff KL6904 Bedienungsanleitung

Beckhoff

Beckhoff KS3222 Bedienerhandbuch

Beckhoff

Beckhoff ELX2792 Bedienungsanleitung

Beckhoff

Beckhoff ELX3312 Bedienungsanleitung

Beckhoff

Beckhoff EL6652-00 0 Series Bedienerhandbuch

Beckhoff

Beckhoff EL7031 Bedienerhandbuch

Beckhoff

Beckhoff EL34x3 Series Bedienerhandbuch

Beckhoff

Beckhoff KL3311 Bedienerhandbuch

Beckhoff

Beckhoff ELX3202 Bedienungsanleitung

Beckhoff

Beckhoff TF6350 Bedienungsanleitung

Beckhoff

Beckhoff KL6224 Bedienerhandbuch

Beckhoff

Beckhoff KL6781 Bedienerhandbuch

Beckhoff

Beckhoff KL2521 Series Bedienerhandbuch

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung