Bed-Check Classic-Check Betriebsanleitung
This guide will assist you with manual programming of the Bed-Check®Classic-Check®control unit.
More detailed manual programming instructions can be found in the User’s Guide booklet.
For programming, only the control unit and power cord are needed. (Neither a Sensormat®nor the nurse call
cord need to be plugged in during programming.)
Arming/Disarming System
Press and release the RESET button to go from MONITOR to HOLD, or
from HOLD to MONITOR, or to silence an alarm. Please note that if the
system is on HOLD, it will reset itself and resume monitoring if weight is
placed on the Sensormat®. In addition, if the RESET button is pressed to
put on HOLD and weight remains on the Sensormat®, the unit will return
to monitoring mode in 25 seconds.
SETTINGS - Any of the following setting changes may be made independently of the others.
We recommend setting tone before volume, as some tones may seem louder than others.
Day/Night Mode Settings
Press and release DAY/NITE button to switch between DAY and NITE
modes. NITE mode is indicated by a blue light in the splash guard.
Alarm Delay Settings
Press and release the ALARM DELAY button to adjust the alarm delay to
1, 2, or 3 seconds.
R
Bed-Check
Reducing the Risk of Falls Through
Innovative Technology Since 1978
R
Bed-Check®
Quick Programming Guide
PO Box 80238, Lincoln, NE 68501 • Toll Free 800-523-7956 • Fax 402-475-4023 • www.bedcheck.com
© 2008 Stanley Security Solutions, Inc. DOC-02-70000-AA
®
Press and release
Press and release
DAY
Mode
NITE
Mode
Press and release
1 second
2 seconds
3 seconds
Quick Programming Guide continued
PO Box 80238, Lincoln, NE 68501 • Toll Free 800-523-7956 • Fax 402-475-4023 • www.bedcheck.com
© 2008 Stanley Security Solutions. DOC-02-70000-AA
®
Tone Setting
The tone setting will be the same for DAY and NITE modes. To change
the tone press and hold the RESET button, then press and hold the
ALARM DELAY button. Release the RESET button to hear current
setting. Then press and release the RESET button until desired tone is
obtained. Release all buttons, press and release RESET once more to lock
setting.
Alarm Volume
The alarm volume can be adjusted separately for both the DAY and NITE
modes. First set the mode for which you are changing the volume (see
other side). Press and hold the RESET button, then press and hold the
DAY/NITE VOLUME button. Release the RESET button to hear current
setting. Then press and release the RESET button until desired volume is
obtained. Release all. Press/release RESET once more to lock the setting.
Press and hold
Press and release
Press and hold
Release; then Press/Release
Release all
Press and release to lock
Low Pitch Warble
High Pitch Warble
Triple Tone
Old McDonald
Mary Had a Little Lamb
The Farmer in the Dell
Comin’ Round the Mountain
Tom, Tom the Piper’s Son
Folk Song
Do - Re - Mi
Display Tone
67 db
73 db
77 db
80 db
81 db
83 db
85 db
Display Decibels
Press and hold
Release; then Press/Release
Release all
Press and release to lock
Andere Bed-Check Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
