Bedrock UPS.500 Bedienungsanleitung
UPS.500
Quick Start Guide
The UPS.500 contains lithium-ion batteries. The product is not
field-serviceable. Contact Bedrock Automation for instructions on
returning the UPS.500.
Never attempt to open the UPS.500 enclosure. The enclosure is
securely sealed. Opening the enclosure will void the warranty and
cause the UPS.500 to be inoperable.
Always use an appropriate fuse on the power in and power out
connections.
For both the panel and pipe mount configurations, it is required
that the UPS.500 mounting bracket is grounded.
Important User Information
Select an input power supply with a rating that is greater than the
UPS.500 power consumption which can be calculated as follows:
((output voltage x configured current limit) +
configured charge power)
The UPS.500 contains lithium-ion batteries. The output port may
carry voltage even when the UPS.500 is not connected to a power
source.
Prior to connecting the cables, read this guide thoroughly, paying
attention to important electrical and safety information.
1 - Status LEDs
Ethernet Activity
Ethernet Link
Tri-color UPS Status
2 - Ports
Note: Bedrock part no. CI00100 or Phoenix
Contact part no. 1656990 must be
used for the Ethernet connector in
order to maintain the IP66/IP67 rating.
Note: A shielded
Ethernet cable is
required.
Power
Out
Power
In Relay
Enable
Ethernet
3 –UPS.500 Block Diagram
Dual
Ideal
Diode
Controller
Dual
Relays
Regulator
Line
In
Enable
DC
Out
Ethernet
Port
Battery
Pack
Charging
Circuit
Microcontroller
Ethernet
Controller
Relay
Input A
Input B
Output
Control
Control
4 –General Wiring Diagram
Note: Battery Enable Connector must be connected prior to power up
Load
Power
Supply
Recommended
Fusing
Power
Out
Power
In
Recommended
Fusing
To Discrete
Inputs for
Alarming Relay
Output
(optional)
Ethernet
24 V Power Supply
Battery
Enable
Connector
Select an input power supply with a rating that is
greater than the UPS.500 power consumption which
can be calculated as follows:
((output voltage x configured current limit) +
configured charge power)
One of the
following:
Workstation
Running
OPC UA
Bedrock
SIO4.E comm.
module
UCG.5
OSA Remote
5 –Bedrock Configuration
Note: Battery Enable Connector must be connected prior to power up.
Bedrock Configuration only valid with SPS.500
One of the
following:
Workstation
Running
OPC UA
Bedrock
SIO4.E comm.
module
UCG.5
OSA Remote
Load
(SPM)
SPS.500
Recommended
Fusing
Power
Out
Power
In
Recommended
Fusing
To Discrete
Inputs for
Alarming Relay
Output
(optional)
Ethernet
Battery
Enable
Connector
Ethernet
Input B
Input A
ORed
Output
Field
Devices
Recommended
Fusing
6 –Parts List (Panel Mount)
1
2
3
ITEM
NO.
DESCRIPTION
QTY.
1
UPS.500 ASSEMBLY
1
2
#14 x 1” SELF TAPPING
SCREW
4
3
UPS MOUNTING BRACKET
1
Use Bedrock Part No. MI00128 when ordering the
UPS Mounting Bracket Assembly (Panel Mount)
7 –Parts List (Pipe Mount)
1
2
4
Use Bedrock Part No. MI00127 when ordering the
UPS Mounting Bracket Assembly (Pipe Mount)
ITEM
NO.
DESCRIPTION
QTY.
1
UPS.500 ASSEMBLY
1
2
3/8”-16 x 3/4 HEX BOLT
4
3
UPS MOUNTING BRACKET
1
4
2” SCHEDULE 40 PIPE
MOUNTING BRACKET
1
5
3/8”- WASHER
4
6
3/8”-16 HEX NUT
4
3
5
6
8 –Mount UPS
2
1
Andere Handbücher für UPS.500
3
Inhaltsverzeichnis
Andere Bedrock UPS Handbücher
Beliebte UPS Handbücher anderer Marken
Pylontech
Pylontech Victron & Pylontech US5000 Bedienungsanleitung
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung
Mecer
Mecer ME-1000-WTU Bedienungsanleitung
Mustek
Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch
Emerson
Emerson Liebert NXL series Bedienungsanleitung
MAKELSAN
MAKELSAN BOXER SERIES Bedienungsanleitung
