Beghelli DECO LED Bedienungsanleitung

INSTRUCTIONS

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS

2. Disconnect power before performing work on electrical equipment.

3. Do not use outdoors.

4. Use caution when servicing batteries.

5. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to tampering.

6. The use of accessory equipment not recommended by Beghelli Inc., may cause an unsafe condition, and will void the unit’s warranty.

7. Do not use this equipment for other than its intended purpose.

8. Servicing of this equipment should be performed by qualified service personnel.

9. SAVE THESE INSTRUCTIONS!

DECO LED

Beghelli U.S.A., 3250 Corporate Way, Miramar, Florida, Tel: (800) 726-4316 Tel: (954) 442-6600 Fax: (954) 442-6677

8/6/2019

Page 1 of 2

Turn off AC power.

Extend unswitched AC line to unit location.

Remove both lenses by pulling away from housing.

Do not lift unit by lenses (Diagram A).

Remove unit back plate by releaseing two tabs at the bottom

with a narrow screwdriver blade, and pull away. (Diagram B).

For WALL OR CEILING MOUNTING, please screw through ap-

propriate keyhole slots and tighten. If ceiling mounted, be sure

to orient the back plate, so the test switch faces the bottom or

desired direction. For JUNCTION BOX MOUNTING, complete

wiring connections as per step 6, and secure to J-box by remov-

ing appropriate knock-outs in back plate. For CONDUIT ENTRY,

secure back palte to wall or ceiling with sutable anchors. Knock

out the conduit entry hole in the top of the unit housing, and

install conduit with bushing.

Attach unswitched AC circuit wires to unit AC input wire with

wire nuts. INSULATE UNUSED LEAD.

For 120 VAC input, follow diagram C.

For 277 VAC input, follow diagram D.

When ready to energize AC circuit, connect red battery lead

to battery positive terminal. Verify battery negative terminal is

connected to battery blue wire.

AC must be off when mating unit housing to back plate. Align

AC connector over circuit board and press onto back plate un-

til the retaining tabs snap through the housing. Reinstall both

lenses by slightly squeezing the top and bottom mounting tabs.

IMPORTANT: The battery in this unit may not be fully charged. After electricity is connected to unit, let battery charge for at least 24 hours, then normal

operation of this unit should take effect. To check, press TEST button. The emergency LED lamps should illuminate. When re-lamping, use only LED

lamps specified in the fixture. Using other lamp types may result in transformer damage or unsafe conditions.

INSTALLATION

Beghelli U.S.A., 3250 Corporate Way, Miramar, Florida, Tel: (800) 726-4316 Tel: (954) 442-6600 Fax: (954) 442-6677

8/6/2019Page 2 of 2

To test, depress test switch. The emergency lamps will illuminate.

When switch is released, LED will go off. Allow unit to charge for 48

hours before full load testing.

Battery: 3.6V 1000mAh Ni-Cd

LED: 2X12PCS SMDLED

Duration time: 100 minutes

TESTING

IMPORTANT NOTICE: This equipment is furnished with a low voltage disconnect circuit to prevent damage by over discharging the

battery. However, if the AC supply to the unit is to be disconnected for prolonged periods of time, the BATTERY MUST BE DISCONNECTED.

If unit fails to perform as described, disconnect AC and battery immediately, and contact the factory, or trained service personnel for

assistance.

TECHNICAL PARAMETERS

WARNING: Unused wires must be capped using enclosed wire nuts.

Inhaltsverzeichnis

Andere Beghelli Beleuchtungsausrüstung Handbücher

Beghelli

Beghelli Salvalavista LED Bedienungsanleitung

Beghelli

Beghelli Maxima Bedienungsanleitung

Beghelli

Beghelli TEMPESTA PLUS HT Bedienungsanleitung

Beghelli

Beghelli Pluraluce Mini Bedienungsanleitung

Beghelli

Beghelli Tempesta Bedienungsanleitung

Beghelli

Beghelli 86 Series Bedienungsanleitung

Beghelli

Beghelli Bravado Unit Bedienungsanleitung

Beghelli

Beghelli Tempesta Bedienungsanleitung

Beghelli

Beghelli LUMINI Bedienungsanleitung

Beghelli

Beghelli Formula 65 LED Bedienungsanleitung

Beghelli

Beghelli Esco Unit Bedienungsanleitung

Beghelli

Beghelli PACO-T20 Bedienungsanleitung

Beghelli

Beghelli OL2-CT Bedienungsanleitung

Beghelli

Beghelli Cyclone Bedienungsanleitung

Beghelli

Beghelli WLX Bedienungsanleitung

Beghelli

Beghelli IP65 Bedienungsanleitung

Beghelli

Beghelli SR Bedienungsanleitung

Beghelli

Beghelli Nova Eco Bedienungsanleitung

Beghelli

Beghelli OTTICA B6L Bedienungsanleitung

Beghelli

Beghelli GDE Combo Bedienungsanleitung

Beghelli

Beghelli STELLA EXIT Bedienungsanleitung

Beghelli

Beghelli Lyra W LED Bedienungsanleitung

Beghelli

Beghelli PRATICA MODULA AT Bedienungsanleitung

Beghelli

Beghelli MPL Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung