BEGLEC MOVING HEAD SPOT Bedienungsanleitung

WWW. BEGLEC.COM

Professional Lighting Technology

User Guide

Please read these instructions carefully before use

Note

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

2.1 Inserting/Exchanging rotating gobos

3. Lamp

4. How To Set The Unit

4.1 Control Panel

4.2 Main Function

5. How To Control The Unit

5.1 Master/Slave Built-In Preprogrammed Function.

5.2 Easy Controller

5.3 Universal DMX Controller

5.4 DMX512 Configuration

5.5 DMX512 Connection

6. Troubleshooting

7. Fixture Cleaning

1. Safety Instruction

WARNING

zPlease keep this User Guide for future consultation. If you sell the unit to another

user, be sure that they also receive this instruction booklet.

zUnpack and check carefully there is no transportation damage before using the

unit.

zBefore operating, ensure that the voltage and frequency of power supply match the

power requirements of the unit.

zThe unit is designed for use with the MSD 250W. Do not use any other type of lamp.

zIt’s important to ground the yellow/green conductor to earth in order to avoid

electric shock.

zThe unit is for indoor use only. Use only in a dry location.

zThe unit must be installed in a location with adequate ventilation, at least 50cm

from adjacent surfaces. Be sure that no ventilation slots are blocked.

zDisconnect main power before fuse/lamp replacement or servicing.

zReplace fuse/lamp only with the same type.

zMake sure there are no flammable materials close to the unit while operating, as it

is fire hazard.

zUse safety chain when fixes this unit. Don’t handle the unit by taking its head only,

but always by taking its base.

zMaximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature

is higher than this.

zUnit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand

during its operation, and allow about 15 minutes to cool down before replacing

bulb or serving, as the unit could be very hot.

zIn the event of serious operating problem, stop using the unit immediately. Never

try to repair the unit by yourself. Repairs carried out by unskilled people can lead

to damage or malfunction. Please contact the nearest authorized technical

assistance center. Always use the same type spare parts.

zDon’t connect the device to any dimmer pack.

zDo not touch any wire during operation as high voltage might be causing electric

shock.

7. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in which

the fixture operates: damp, smoky or particularly dirty surrounding can cause greater

accumulation of dirt on the unit’s optics.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

EC Declaration of Conformity

We declare that our products (lighting equipments) comply with the following

specification and bears CE mark in accordance with the provision of the

Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55014-1: 1993, EN61000-3-2: 1995, EN61000-3-3: 1995

EN55014-2: 1997 CATEGORY II

EN61000-4-2: 1995, EN61000-4-3: 1995, EN61000-4-4: 1995

EN61000-4-5: 1995, EN61000-4-6: 1995, EN61000-4-11: 1994

Harmonized Standard

EN60598-1: 1993

Safety of household and similar electrical appliances

Part 1 : General requirements

Following the provisions of the Low Voltage Directive 73/23/EEC and 93/68/EEC.

EC Declaration of Conformity

We declare that our products (remote controller) comply with the following

specification and bears CE mark in accordance with the provision of the

Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55015: 1993

EN50082-1: 1997

EN61000-3-2: 1995

EN61000-3-3: 1995

Please read carefully the instruction, which includes important

information about the installation, usage and maintenance.

G. If The pan belt is broken

1. Turn off the main power.

2. Unscrew all the screws (A) and open the base-housing cover (B).

3. Unplug all the connect wires (C) that from the arm to PC board and igniter.

4. Unscrew the screws (D) that fix the bridge (E).

5. Unscrew the screws (F) that fix the axis gear (G).

6. Change a new belt (H) by going through all connecting wires that from the arm to base,

and through the bridge for correct position.

7. Set up the gear axis to the bridge and screwed it. Note: do not press the belt.

8. Put the belt around the axis gear and motor gear.

9. Plug all the connect wires (C) that form the arm to PC board and igniter.

10. Adjust the pan home position.

11.Screw the base-housing cover (B).

Warning

zTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

zNever touch bulb with bare fingers, as it is very hot after using.

zHot lamp explosion hazard. Do not open the unit within five minutes after switching off.

zDo not start on the unit without bulb enclosure or housing are damaged.

zThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

zDo not look directly at the light while the bulb is on.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt

any repairs yourself. In the unlikely event your unit may require service, please contact

your nearest dealer.

Installation

The unit should be mounted via its mounting system ( as shown below ) on the bottom of the

base. Use clamps to fix the unit to truss. Always ensure that the unit is firmly fixed to avoid

vibration and slipping while operating. Always ensure that the structure to which you are

attaching the unit is secure and is able to support a weight of 30 kgs for each unit.

2. Technical Specification

Power supply

- AC 120V~60Hz or 230V/240V/250V 50/60Hz

Lamp

- Discharge lamp MSD 250W GY9.5

Optical system

- Standard 13° focused beam angle.

- Focus adjustable by DMX control

Shutter/Dimmer

- Blackout, 0~100 smooth dimming and strobe speed variable(1~10 flashes per second).

Gobo wheel

- Independent gobo wheel with 7 gobos plus open, gobos are interchangeable: 4 metal

gobos, 2 glass gobos, and 1 effect gobo. 3 additional metal gobos and 2 effect gobos are

included.

- Gobo wheel rotates with variable speed. Shaking effect included.

Color wheel

- Independent color wheel with 9 dichroic mirrors plus white.

- Color wheel rotates with variable speed, giving rainbow effect.

Prism - 3-facet prism rotates in both directions at variable speeds

Movement

- Pan: 540° in 2.8 second.

- Tilt: 270° in 1.6 second.

DMX Channels

- Standard DMX512 signal addressing and can be controlled by any universal DMX

controller.

Channel 1 = Pan motion Channel 9 = Gobo

Channel 2 = Tilt motion Channel 10 = Gobo Rotation

Channel 3 =Pan/Tilt Speed select Channel 11 = Prism

Channel 4 = Dimmer Channel 12 = Prism Rotation

Channel 5 = Shutter/ Shaking Channel 13 = Focus

Channel 6 = Color Channel 14 = Pre-programmed Show Pattern

Channel 7 = No Function Channel 15 = Pre-programmed Beam Pattern

Channel 8 = Reset Channel 16 = Reset

Dimension: 360mm x 397mm x 503mm (L x W x H)

Weight: 26 kg

6. Troubleshooting

Following are a few common problems that may occur during operation. Here are some

suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connect power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of

the unit or the previous one.

4. Try to use another DMX controller.

5. Check in the DMX cables run near or run alongside to high voltage cables that may cause

damage or interference to DMX interface circuit.

C. Some units don’t respond to the easy controller

1. You may have a break in the DMX cabling. Check the LED for the response of the master/

slave mode signal.

2. Wrong DMX address in the unit. Set the proper address.

D. No response to the sound

1. Check the unit that is not receiving DMX signal.

2. Check microphone to see if it is good by tapping the microphone

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition.

F. The lamp is cutting out intermittently

1. The lamp is not working well. Check the main voltage either too high or too low.

Internal temperature may be too high. Check and if necessary replace the fan on the head.

5.5. DMX512 Connection

The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.

1. If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin adapter.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm 1/4W

resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the

DMX-output of the last unit.

3. Connect the unit together in a “daisy chain” by XLR plug from the output of the unit to the

input of the next unit. The cable cannot be branched or split to a “Y” cable. DMX512 is a

very high-speed signal. Inadequate or damaged cables, soldered joints or corroded

connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX circuit, when

power is disconnected to the unit.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pins XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

Luminous intensity:

2.1. Inserting/Exchanging rotating gobos

DANGER!

Install the gobos with the device switched off only.

Unplug from mains before changing gobos!

Open the cover by loosening the fastening screw at the sides of the cover.

If you wish to use other forms and patterns as the standard-gobos, or if the gobos are to be

exchanged, remove the fixation ring with an appropriate tool. Remove the gobo and insert the

new gobo. Press the fixation-ring together and insert it in the front of the gobo.

CAUTION!

Never unscrew the screws of the rotating gobo as the ball bearing

will otherwise be opened!

3. Lamp

Because of its high internal pressure, there might be a risk that the Discharge lamp would

explode during operation. The lamp emits intense UV radiation which is harmful to the

eyes and skin. The high luminance of the arc can

cause severe damage to the retina if looks directly

at the lamp.

Discharge lamp:

MSD 250W

1.Always switch off the main supply and never

handle the lamp or luminaries when is hot.

2. Do not touch the bulb with bare hands. If this

happens, clean the lamp with denatured alcohol

and wipe it with a lint free cloth before installation.

3. The lamp generates UV radiation. Never operate the

lamp without appropriate shielding.

4. When burning, the lamp operates at high pressure

and there is a slight risk of arc tube rupture. The risk

increases with age, temperature and improper

handling of the lamp. Do not use the lamp any

longer than its specified life.

5. Make sure the lamp is located in the center of the

reflector for the best spot. Adjust lamp

position by screws A, B and C.

i.) Channel 14 –Pre-programmed show pattern:

1.) DMX value 0-31,the fixture is still controlled by DMX control .

2.) For DMX Value above 31,all the DMX control will be invalid .The fixture will

run the pre-programmed show patterns(Pan/Tilt movement).

ii.) Channel 15-Pre-programmed beam pattern:

One can select the beam pattern only when the pre-programmed show pattern is

activated.

iii.) For DMX Reset, put DMX value of CH-8 & CH-16 to 255.

In case of replacement of the lamp or maintenance, do not open the

fixture within 15 minutes until the unit cools down after switching off.

5.4. DMX512 Configuration

4. How To Set The Unit

4.1. Control Panel

Display

To show the various menus and the selected functions.

LED

DMX On DMX input present

MASTER On Master mode

SLAVE On Slave mode

SOUND Flashing Sound activation

Button

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

Remote controller input

By connect to the 1/4” microphone jack to control the unit for Stand by, Strobe/Next and

Show 1/Slow/Show 2 function.

Sensitivity

To adjust the sound-receiving sensitivity.

Microphone

To receive audio signal for sound activation.

DMX input/output

For DMX512 link, use 3-pin XLR plug cable to link the unit together.

4.2. Main Function

To select any of the pre-set functions, press the MENU button up to when the required one is

shown on the display. Select the function by ENTER button and the display will blink. Use

DOWN and UP button to change the mode. Once the required mode has been selected,

press the ENTER button to setup or it will automatically return to the main functions without

any change after idling 8 seconds. To go back to the functions without any change press the

MENU button. The main functions are shown below:

Focus Adjust

Self-Test

Reset

Fixture Hours

Display Inversion

Display Normal

Tilt Inversion

Tilt Normal

Pan Inversion

Pan Normal

Split Color

Normal Color

Slave mode " 2 Light Show "

Slave Mode " Normal "

Show Mode " Show 2 "

Show Mode " Show 1 "

DMX512 Address Setting

Blackout Mode " No Blackout "

Blackout Mode " Yes Blackout "

5.2. Easy Controller

The easy remote controller is used only in master/slave mode. By connecting to the 1/4”

microphone jack of the first unit, you will find that the remote control on the first unit will control

all the other units for Stand by, Strobe/Next/Strobe and Show 1/Slow/Show 2 functions.

1. STAND BY: To blackout all the units.

2. FUNCTION - STROBE/NEXT/STROBE

Under SHOW 1 and SHOW 2 mode, the units will strobe in three different ways:

a) Strobe in different gobos and colors.

b) Synchronous strobe in white color.

c) Two-light strobe in white color.

Under SLOW mode, press FUNCTION button to choose desired

color and gobo. It will change ten colors and then change one

gobo.

3.MODE - SHOW 1/SLOW/SHOW 2

When the LED is off, it is in SHOW 1 mode, and blinking in SHOW

2 mode. The unit’s movement- Pan/Tilt & Gobo/Color is sound

activated. If the LED on, it is in SLOW mode, Pan/Tilt is sound

activated but Gobo/Color wheel are static, controlled by Next

button.

5.3. Universal DMX Controller

If you use a universal DMX controller to control the units, you have to set DMX address from 1

to 512 channel so that the units can receive DMX signal.

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press and keep ENTER button pressed up to when the

display stops blinking or storing automatically 8 seconds later. To go back to the functions

without any change press the MENU button again. Please refer to the following diagram

to address your DMX512 channel for the first 4 units.

10A

5. How To Control The Unit

You can operate the unit in three ways:

1. By master/slave built-in preprogram function

2. By easy controller

3. By universal DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address setting

will be effected at once. Every time you turn the unit on, it will show AE16 on the display and

move all the motors to their ‘home’ position and you may hear some noises for about 20

seconds. After that the unit will be ready to receive DMX signal or run the built-in programs.

5.1. Master/Slave Built-In Preprogrammed Function

You can select blackout mode in (yes blackout) or (no blackout)

mode while the unit is turned on. By linking the units in master/slave connection, the first unit

will control the other units to give an automatic, sound activated, synchronized light show. This

function is good when you want an instant show. You have to select (show 1) or

(show 2) mode by easy controller. Its DMX input jack will have nothing plugged into it,

and Its master LED will be constantly on and sound LED will flash to the music. The other

units will have to set in slave mode and select (normal) or (2 light

show) mode, Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave

LED lights will constantly on.

2-light show

In (slave mode), means the unit works normally and means

2-light show. In order to create a great light show, you can set on the second unit to

get contrast movement to each other, even if you have two units only.

DMX512 Address Setting

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press the ENTER button to setup or automatically

return to the main functions without any change after 8 seconds. To go back to the functions

without any change press the MENU button again.

Show Mode

Press the MENU button up To when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (show 1) or

(show 2) mode. Once the mode has been selected, press the ENTER button to setup

or automatically return to the main functions without any change after 8 seconds. To go back

to the functions without any change press the MENU button again.

Press the MODE button from the easy controller to select the (show 1) or

(show 2) mode. When the LED is off, it is in SHOW 1 mode, and blinking in SHOW 2 mode

Show 1 mode- Fixture is placed on the floor. Tilt movement angle 210°.

Show 2 mode-Fixture is fixed under ceiling. Tilt movement angle 90°.

Slave Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (normal) or

(2 light show) mode. Once the mode has been selected, press the ENTER button to

setup or automatically return to the main functions without any change after 8 seconds. To go

back to the functions without any change press the MENU button again.

Blackout Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (yes

blackout) or (no blackout) mode. Once the mode has been selected, press the

ENTER button to setup or automatically return to the main functions without any change after

8 seconds. To go back to the functions without any change press the MENU button again.

Inhaltsverzeichnis

Andere BEGLEC Beleuchtungsausrüstung Handbücher

BEGLEC

BEGLEC Magic Gobo Bedienungsanleitung

BEGLEC

BEGLEC JB SYSTEMS Light Magic LED II Bedienungsanleitung

BEGLEC

BEGLEC JBSystems Light LED Par 56 Bedienungsanleitung

BEGLEC

BEGLEC iSolution IMOVE-5S Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung