BeiJer IFC ETTP Bedienungsanleitung

IFC ETTP, IFC ETCX

Manual

MA00328D 2001-12 English Svenska

Foreword

Beijer Electronics

Manual IFC ETTP, IFC ETCX

Foreword

This manual describes the installation and function of the Ethernet expansion

cards IFC ETTP and IFC ETCX.

The cards can be connected to the operator terminals with expansion slots.

Besides this manual is the manual for the operator terminals and the

programming tool for the operator terminals also available.

 Beijer Electronics AB, MA00328D 2001-12

All examples in this manual are used solely to promote understanding of how the equipment works and its

operation. Beijer Electronics AB takes no responsibility if these examples are used in real applications.

Because of the great many areas for this equipment, the user himself must acquire the appropriate knowl-

edge needed to use the equipment correctly for particular applications.

Beijer Electronics AB absolves itself of all responsibilities for damage and injuries that may occur during

installation or use of this equipment.

Beijer Electronics AB absolves itself of all responsibilities for any type of modification made to the

equipment.

Beijer Electronics AB absolves itself of all responsibilities for damage caused to its products by other brands

of equipment linked to them.

Foreword

Beijer Electronics

Please fill this form out with any suggestions regarding the manual.

This page, or a copy of it, can be sent to us at the addresses below.

Name ............................................................................

Company............................................................................

Address ............................................................................

City, Zip code.....................................................................

Country ............................................................................

Telephone...............................Fax.......................................

E-mail ............................................................................

Please fax this page to the Marketing epartment,

Beijer Electronics AB at +46-40-93 23 01,

or send it by conventional mail to

The Marketing epartment, Beijer Electronics AB

Box 426, SE-201 24 MALMÖ, Sweden.

Comments can also be sent to manual@beijer.se.

Comments regarding MA0032 D Page

Safety precautions

Beijer Electronics

Safety precautions

General

– Check the delivery for transport damage. If damage is found, advise the

supplier.

– The product fulfils the requirements of article 4 of EMC directive

89/336/EEC.

– Do not use the product in an explosive environment.

– Modifications, changes and additions to the product are forbidden.

– Use only spare parts approved by Beijer Electronics AB.

– Read the user instructions carefully before use.

– The equipment should be operated by qualified personnel only.

At installation

– The product is constructed for stationary installation.

– Install the product according to the accompanying installation instructions.

– The product must be grounded according to the accompanying installation

instructions.

– The equipment must be installed by qualified personnel.

– Separate cables for high voltage, signals and supply.

In use

– Keep the equipment clean.

– Emergency stop and other safety functions should not be controlled from the

terminal.

Service and maintenance

– The agreed guarantee applies.

– Repairs should be made by qualified personnel.

Safety precautions

Beijer Electronics

At disassembly and scrapping

–Local regulations apply concerning recycling of products or parts.

Contents

Beijer Electronics

Contents

1Installation................................................................................................8

1.1 Installation of one expansion card................................................8

1.2 Installation of two expansion cards.............................................10

1.3 The LEDs on IFC ETCX and IFC ETTP..................................11

2 Settings in the programming tool...........................................................12

2.1 Define slot .................................................................................12

2.2 Settings for TCP/IP ...................................................................14

Contents

Beijer Electronics

Installation

Beijer Electronics 8

1 Installation

The expansion cards IFC ETTP and IFC ETCX are used to connect the

operator terminals to an Ethernet network for communication via TCP/IP. The

connection can be made by either twisted pair (TP) or coaxial cable (CX).

Further information about configuration of the terminals to TCP/IP network is

available in the manual for the terminals.

This chapter describes how to mount the expansion card in the terminal.

1.1 Installation of one expansion card

Perform the following steps to mount an IFC ETTP or IFC ETCX expansion

card:

1. Switch the terminal power off.

2. Make sure that the ESD protection is good.

3. Remove the cover plate on the rear of the terminal, and the two expansion

plates on the short side. In terminals equipped with two expansion slots, the

slots are called Slot 1 and Slot 2. In terminals with only one expansion slot,

it is called Slot 1.

Slot 1

Slot 2

Installation

9Beijer Electronics

4. Put the jumper J1 on the expansion card in the position SLOT 1 if the

expansion card is mounted in Slot 1, and in position SLOT 2 if the card is

mounted in Slot 2.

5. Mount the expansion cables with the components of the expansion card

placed upwards. One of the expansion cables is mounted between X1 on the

CPU card and X1 on the expansion card, and the other cable between X2

on the CPU card and X2 on the expansion card.

6. Fasten the card with the spacers or the screws. Use the screws if the

expansion card is mounted in Slot 1, and the spacers if the card is mounted

in Slot 2.

7. Check that the expansion cable is correctly mounted.

8. Mount the cover plates.

Installation

Beijer Electronics 10

1.2 Installation of two expansion cards

Two expansion cards can be mounted in some terminals. They are mounted in

parallel to the connector on the CPU card in the terminal. Two expansion cards

can be connected via one expansion cable since there is a parallel contact on the

cable. The connector in the middle is used for the expansion card placed in Slot

1, and the end connector is used for the expansion card placed in Slot 2. If only

one card is used either connector can be used.

The connector X1 on the expansion card in Slot 2 is connected to the connector

X1 and the CPU card in the terminal via the X1 connector on the expansion

card in Slot 1. If the X2 connector on the CPU card in the terminal is used by

any or both cards, this connector is connected to the X2 connector on the

expansion card.

When two expansion cards are mounted in the same terminal you mount the

card in Slot 1 with the distances and the card in Slot 2 with the screws in the

distances.

Card in

Slot 2

Card in

Slot 1 X2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung