BEING L Series Betriebsanleitung

BEING Instrument Inc.

1.0 INTRODUCTION

This programming guide provides the user of the following BEING laboratory instruments the

ability to change the backlit LCD controller’s internal parameters to allow the instrument to

work more eectively and eciently for your operation, process, or experiment.

BIF-16, -35, -55, -120, -200, -400

Mechanical Convention Incubators

BIT-16, -35, -55, -120, -200

Natural Convention Incubators

BIC-60, -120, -250

Cooling incubators

BOF-30, -50, -120, -200, -400

Mechanical Convention Drying Ovens

BON-30, -50, -115, -200

Natural Convention Drying Ovens

BOV-20, -50, -90

Vacuum Ovens

BWB-05, -12, -22

General Purpose Water Bath

2.0 TABLE OF CONTENTS

Safety messages ..................................................................................................................................................................................... 03

Controller elements overview .......................................................................................................................................................... 04

Changing temperature unit of measurement............................................................................................................................. 05

Calibration after unit of measurement change .................................................................................................................... 06-07

What is a multi-step program ..................................................................................................................................................... 08-09

Turn on/o multi-step programs .....................................................................................................................................................10

Programming multi-step programs ................................................................................................................................................ 11

Selecting multi-step program to run .............................................................................................................................................. 12

Setting up program cycling ...............................................................................................................................................................13

Setting up RUN delay — xed value (single-step) programs ................................................................................................ 14

Setting up RUN delay — multi-step programs ........................................................................................................................... 14

Changing power-up mode ................................................................................................................................................................. 15

Internal parameters overview..................................................................................................................................................... 16-17

BEING Instrument Inc. 03

Safety Messages

Safety Message

Be sure that you are completely familiar with the safe operation of each BEING series.This unit may be connected to other machinery, such as a vacuum pump. Improper use can cause serious or fatal

injury.

Installation and repair procedures require specialized skills with laboratory equipment and electricity. Any person that installs or repairs this unit must have these specialized skills to ensure that this

unit is safe to operate. Contact BEING Instrument, Inc. or their local authorized distributor for repairs or any questions you may have about this unit’s safe installation and operation.

The precaution statements are general guidelines for the safe use and operation of these instruments. It is not practical to list all unsafe conditions.Therefore, if you use a procedure that is not recom-

mended in this programming guide, you must determine if it is safe for the operator and all personnel in the proximity to the instrument. If there is any question of the safety of a procedure, please

contact BEING Instrument before starting or stopping the instrument.

This equipment contains high voltages. Electrical shock can cause serious or fatal injury. Only qualied personnel should attempt the startup procedure or troubleshoot this unit.

• Documentation must be available to anyone that operates this equipment at all times.

• Keep non-qualied personnel at a safe distance from this unit.

• Only qualied personnel familiar with the safe installation, operation, and maintenance of this unit should attempt startup or operating procedures.

• Always stop the instrument before making or removing any connections.

Symbols used in this Programming Guide

The following signal word panels, safety symbols, and non-safety symbols are used to alert you to potential personal injury hazards or information of importance. Obey all safety messages that

follow these symbols to avoid possible personal injury or death.

• Signal word panels

Signal word panels are a method for calling attention to a safety messages or property damage messages and designate a degree or level of hazard

seriousness. It consists of three elements: a safety alert symbol, a signal word and a contrasting rectangular background. The following signal word

panels are in accordance with ANSI Z535.4-2111 (R2017) and ISO 3864 standards.

Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury.

• Safety symbols

Safety symbols are graphic representations—of a hazard, a hazardous situation, a precaution to avoid a hazard, a result of not avoiding a hazard, or any

combination of these messages—intended to convey a message without the use of words.The following safety symbols are used in this quick start guide.

Mandatory Warning

General alert. Mandatory action. Safety Alert Symbol. General caution.

Hot Surface

Prohibition

Do not touch uid.

Wear protective gloves.

BEING Instrument Inc.

PROG Area: Displays the program working or setting group. Controller

is capable of programming and storing up to 7 programs.

STEP Area: Displays the number of the step within a program. There

are 9 steps available for each program.

TIME Area: Displays the running time or parameter value.

TEMP Area: Displays the measured (actual) temperature within the

unit’s chamber. Also, displays the ambient room temperature when

requested.

SET Area: Displays the temperature setpoint.

RUN: Illuminates when the unit’s program is working. Turns o when

program is stopped.

HEAT: Arrows illuminate and blinks when the unit’s heater is on.

Turns o when heating elements are o.

COOLING: Snowake illuminates and blinks when the unit’s cooling

is on. Turns o when cooling system is o. Series BIC only.

FAN: Fan blades illuminate and blinks when the unit’s circulation fan

is on. H (high), M (medium), and L (low) indicate the fan speed. Turns

o when fan is o. Series BIF, BIC, and BOF only.

Water Level: Indicates high and low water bath levels.

Visible Alarm: Illuminates when the program has completed, has

been stopped by user, or when an over temperature condition

occurs. Additionally, when the visible alarm illuminates an audible

alarm will start.

Audible Alarm Disabled: Illuminates when the user presses any key

or when the unit’s power is turned o.

Keys

SETTING: Starts the programming of the temperature and run time.

Accepts the temperature and run time values.

Shift: For changing the parameter value being set and viewing

ambient temperature.

Decrease: Used for setting parameter value, modication of various

values, or start/stop auto-tuning.

Increase: Used for setting parameter value, or press and hold for

more than 2 seconds to view the remaining program time.

RUN/STOP: Press for 2 seconds to run or stop the controller.

Controller Element Overview

BEING Instrument Inc.

STEP 1: Enter Level 3 of controller internal parameters.

Press and hold the SETTING and shift keys for 3 seconds to enter

the controller’s internal parameter settings.

Time area will change and rst digit will blink.

Temperature setpoint must be changed manually.

Units are shipped with temperature measurement set to Celsius (OC).

Parameter CF=0000.

Changing Temperature Unit of Measurement

STEP 2: Enter Level 3 code LK=0088.

STEP 3: Scroll to parameter CF.

STEP 4: Change parameter CF.

STEP 5: Set parameter and return to standard state.

Press the increase key to enter the rst code digit. Press the shift

key to move to the second code digit. Digit will blink. Press the

increase key to enter the second code digit.

Press the SETTING key to enter the Level 3 controller parameters.

First available parameter will appear.

Press the SETTING key 15 time to scroll through parameters until

the parameter CF appears.

Press the increase or decrease key to change the rst digit.

CF=0000 Celsius (OC)

CF=0001 Fahrenheit (OF)

Press the SETTING key 2 times to set parameter CF and return to

standard state.

Upon changing the temperature unit of measurement, the

actual temperature will change its value.

BEING Instrument Inc.

Calibration After Unit of Measurement Change

Check the instrument’s chamber temperature after changing

the unit of measurement to ensure the controller is measuring

it accurately.

Tools Needed:

A remote-monitoring thermocouple thermometer with a

NIST-traceable calibration certicate.

Series BIF, BIT, BOF, and BON

STEP 1: Place test materials in chamber, set program, and

press run for 3 seconds.

Compare the thermometer’s and probe’s temperature ratings against the

series operating range to ensure compatibility.

Series BOV: A ribbon lead thermocouple is required so as not to damage

the door seal. Additionally, the lead’s and probe’s materials must be rated for

temperatures up to ambient + 200OC (ambient + 392OF).

STEP 2: Insert thermometer probe into test hole.

Upon reaching the set temperature, insert thermometer probe

into the test hole.

STEP 4: Compare thermometer readings to set and present

temperatures. If SV1≠PV1≠TV1 or SV2≠PV2≠TV2, move

to STEP 5.

Make sure thermometer is stable. Then record the set temperature (SV1 &

SV2), present value (PV1 & PV2), and thermometer reading (TV1 & TV2).

STEP 3: Run test again at a second set temperature (SV2) at

least 10OC (18OF) greater than the rst.

Series BOV

STEP 1: Place test materials in chamber. Place temperature

probe in the center of the chamber. Close and lock

door. Set program and press run for 3 seconds.

STEP 3: Compare thermometer readings to set and present

temperatures. If SV1≠PV1≠TV1 or SV2≠PV2≠TV2, move

to STEP 4.

Make sure thermometer is stable. Then record the set temperature (SV1 &

SV2), present value (PV1 & PV2), and thermometer reading (TV1 & TV2).

STEP 2: Run test again at a second set temperature (SV2) at

least 10OC (18OF) greater than the rst.

Series BIC

STEP 1: Place test materials in chamber, set program, and

press run for 3 seconds.

STEP 2: Open test hole.

Upon reaching the set temperature, insert thermometer probe into the

test hole.

STEP 5: Compare thermometer readings to set and present

temperatures. If SV1≠PV1≠TV1 or SV2≠PV2≠TV2, move

to STEP 6.

Make sure thermometer is stable. Then record the set temperature (SV1 &

SV2), present value (PV1 & PV2), and thermometer reading (TV1 & TV2).

STEP 4: Run test again at a second set temperature (SV2) at

least 10OC (18OF) greater than the rst.

Thermometer probe’s outer diameter must be less than 8mm.

STEP 3: Insert thermometer probe into test hole.

The test hole is Ø25mm and located on the right

side of the oven.

BEING Instrument Inc. 07

Series BWB

STEP 1: Fill chamber. Place test materials in chamber. Close

chamber cover. Set program and press run for

3 seconds.

STEP 4: Compare thermometer readings to set and present

temperatures. If SV1≠PV1≠TV1 or SV2≠PV2≠TV2, move

to STEP 5.

Make sure thermometer is stable. Then record the set temperature (SV1 &

SV2), present value (PV1 & PV2), and thermometer reading (TV1 & TV2).

STEP 3: Run test again at a second set temperature (SV2) at

least 10OC (18OF) greater than the rst.

STEP 2: Upon reaching set temperature, open chamber cover.

Insert the thermometer probe into the center of bath.

The Math

STEP 4/5/6: Perform the following calculations to determine

Pb and PK.

Full Scale Adjustment (Slope)

PK={[((TV2-TV1))/((SV2-SV1))]-1}x 4000

Zero Adjustment (Intercept)

Pb=TV2-{[PK/(4000/SV2)]+SV2

BEING Instrument Inc.

What is a Multi-step Program

BEING Instrument Inc. 09

BEING Instrument Inc.

Turning On/O Multi-step Programs

STEP 1: Enter Level 4 of controller internal parameters

Press the SETTING and SHIFT keys for 3 seconds to enter the

controller’s internal parameter settings.

Time area will change and rst digit will blink.

Upon initializing the unit for the rst time, user needs to set the temperature

and time for each step in a program.

Units are shipped with the controller set to xed value (single-step)

programs. Parameter Mo=0000.

STEP 2: Enter Level 4 code. LK=8286

STEP 3: Change parameter Mo

STEP 4: Set parameter and return to standard state

Press the INCREASE key to enter the rst code digit. Press the

SHIFT key to move to the second code digit. Digit will blink. Press

the INCREASE key to enter the second code digit.

Follow the same procedure for the third and fourth code digits.

Press the SETTING key to enter the Level 4 controller parameters.

The Mo parameter will appear.

Press the INCREASE or DECREASE key to change the rst digit.

Mo=0000 Fixed value (Single-step) program

Mo=0001 Multi-step programs

Press the SETTING key 1 time to set parameter Mo and return to

standard state.

Upon changing to multi-step progams, the controller screen will

change to PROG 1.

Andere Handbücher für L Series

Inhaltsverzeichnis

Andere BEING Controller Handbücher

BEING

BEING L Series Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung