Bell System Bellissimo Bedienungsanleitung

PD-120 Issue 1 March 2008

Bell System (Telephones) Ltd.

bellissimo

Video Door Entry System

BSSW Gate Controller

Installation & Operation Manual

This manual applies to the following : –

bellissimo video systems

bellcall audio systems

Combined bellissimo and bellcall sites

Where a gate or gates is common to multiple blocks

bellissimo BSSW Gate Controller

PD-120 Issue 1 Installation and Operating Manual Page 2 of 14

bellissimo BSSW Gate Controller

PD-120 Issue 1 Installation and Operating Manual Page 3 of 14

TABLE OF CONTENTS

TABLE OF CONTENTS......................................................................................................3

INTRODUCTION .................................................................................................................4

DESCRIPTION .....................................................................................................................4

MAIN FEATURES.................................................................................................................4

DESIGN CONSIDERATIONS..............................................................................................4

APPLICATION......................................................................................................................4

LIMITATIONS.......................................................................................................................4

INSTALLATION & COMMISSIONING................................................................................5

CHECKLIST.........................................................................................................................5

WIRING..............................................................................................................................5

COMMISSIONING.................................................................................................................6

PROGRAMMING PHONES THROUGH A BSSW........................................................................6

SETTING UP THE BSSW GATE CONTROLLER / BLOCK ISOLATOR ...........................................7

TROUBLESHOOTING ........................................................................................................8

QUICK FAULT REFERENCE...................................................................................................8

SPECIFICATIONS...............................................................................................................9

DIAGRAM A – BELLISSIMO GATE AND BLOCK WIRING.............................................10

DIAGRAM B – BELLCALL GATE AND BLOCK WIRING................................................11

DIAGRAM C – BSSW GATE SWITCHER DETAIL WIRING ............................................12

DIAGRAM D – BSSW GATE SWITCHER PCB LAYOUT ................................................13

bellissimo BSSW Gate Controller

PD-120 Issue 1 Installation and Operating Manual Page 4 of 14

Introduction

Description

The BSSW gate controller is used in two level “gate and block” applications to provide

block isolation where a main gate is used to access 2 or more blocks. Each block

operates independently from local entrances when not being called from the gate.

Up to 4 gates may be independently wired to each BSSW.

Each gate may consist of multiple panels and associated controllers.

Main Features

●4 independent entrance gates per controller.

●Simple address translation to allow one button per flat panels at the block.

Design Considerations

Application

The BSSW has the main purpose of being a two level switcher and is primarily intended

for gate and block architecture.

However it can also be used to apply pure block isolation if required and may be

appropriate for multiple riser application.

One limitation is that there should only be three controllers of any type between the

camera and the videophone. Applications with four controllers are not qualified.

Address translation can be used to allow use of one button per input panels for local

“block” doors. These generate low valued and fixed addresses e.g. a BSD8 gives 1 to 8, a

BSD72 gives 1 to 72. For these SW2 and SW3 allow address translation from the HIGH

postal address down to the LOW local address by subtracting any number from 0 to 239.

typically local addressing starts at 1, so if the postal address for that phone is N, set the

total on the switches to N-1.

EXAMPLE. A scheme of small blocks has addresses “Orchard Close 1-84” and one block

is 70-75. SW2 & SW3 need to add up to 69, so set SW2 to 3 (8), SW3-1 ON and SW3-2

OFF (60), SW3-3 ON and SW3-4 OFF (1) which adds up: 8+60+1=69. Phone addresses

in the block are 1-6.

Limitations

Door left open status is local to a block, that is phones in an isolated block only indicate

“door open” from door controllers in that block.

When a block is in use (Busy) a call from the gate will “Fail” rather than indicate “Busy”.

bellissimo BSSW Gate Controller

PD-120 Issue 1 Installation and Operating Manual Page 5 of 14

Installation & Commissioning

Checklist

The following checklist is a summary of what is required. Refer to the relevant pages for

further details.

●Ensure that ‘Design Considerations’ on page 4 have been understood.

●Confirm that Cat5 cable has been specified.

●Install the system according to instructions in this section.

Wiring

Refer to the diagrams from page 10 onwards as appropriate for the equipment you have.

All wiring is carried out using a mixture of Cat5 for the signal wiring and 1mm² (or greater)

cores for the power wiring. Refer to the main system manuals for detailed information.

Gate Controller

The BSSW gate controller is wired between the block door controllers and the video

controllers, so would normally be wall mounted next to a door controller.

Wiring the BSSW between the local door controller(s) and the video controller(s) prevents

potential camera switching problems when a gate is calling.

Gate Entrance Controller

The gate entrance controller, which is of course a door controller, should be mounted as

such. The location will be site dependant in order to meet the 50m requirement.

The output Cat5 has to daisy chain from block to block in order to preserve the quality of

the video signal.

In the case of two or more gate entrances, the daisy chained Cat5 cable need not take the

same route, just the shortest.

A B

bellissimo BSSW Gate Controller

PD-120 Issue 1 Installation and Operating Manual Page 6 of 14

Commissioning

The major components of the bellissimo Digital system are fitted with high quality

pluggable screw terminal blocks. This enables all the connections to the system to be fully

completed, whilst easily isolating individual pieces of equipment during testing and

commissioning.

It is highly recommended that the blocks are first tested with the BSSW controller

bypassed. Once the block is known to be working correctly, connect the BSSW controller

in order to test the gate connection.

Programming Phones Through a BSSW

Draft

When using BC801 or BSA phones in a bellcall system the phones need to be

programmed. Phones can be programmed from a local panel or from the gate panel.

Bell System recommend that phones are pre-programmed prior to installation onto the

wall, this can speed up the process and reduce the manpower requirement.

This programming can be done on site using a temporary set-up or prior to going to site

using a bench set-up.

Alternatively phones can be ordered pre-programmed for a small extra cost (use part

number BC801/P or BSA/P and provide a list of required numbering).

When programmed from the gate panel any address translation set at a BSSW is ignored

and the phone is programmed with the address entered at the panel.

Example 1. A gate and block system has a small block with six flats and a one button per

flat panel has been used locally, however the flats have postal addresses 70 through 75.

The local controller uses addresses 1 to 6 and so this is the address required for the

phones. The BSSW is set for an address translation of –69 so that 70 becomes 1 and so

on. The phones have already been installed and so they are to be programmed from the

gate. The standard programming method for the controller is used (see the correct

controller manual) and the first phone (70) is programmed as 1, and then tested as 70.

The phones would also be checked from the local panel.

WARNING. When the programming code is entered from the gate, all phones in the

system become active and await being picked up!!. To avoid any side effects it would be

feasible to temporarily disconnect all but one BSSW, otherwise BEWARE!!.

bellissimo BSSW Gate Controller

PD-120 Issue 1 Installation and Operating Manual Page 7 of 14

Setting Up the BSSW Gate Controller / Block Isolator

There are 4 inputs for sources common to multiple blocks which can be used as

termination or passthru. In a bellissimo video system the cable runs for passthru must be

daisy chained, but for bellcall audio they can be star or combination wired. The terminator

is for bellissimo video systems only.

The Input and output connections are again specific to bellissimo video use where the

video signal is switched to maintain termination. For bellcall audio use they are identical.

The input and output connections are connected into the isolated block (group of phones).

Door panels connected into the isolated block can only call phones within the block,

whereas door panels connected to the gate inputs can call into the block whenever there is

no ongoing call activity.

SW2 & SW3 Setting – Block Address Offset

For systems where all the panels are digital, then SW2 will remain in the 0 or OFF

position. All panels use the postal address so there is normally no need fro translation.

However blocks tend to be small and may use one button per input panels which generate

low valued and fixed addresses (BSD8=1-8, BSD72=1-72). For these SW2 and SW3

allow address translation from the HIGH postal address down to the LOW local address by

subtracting any number from 0 to 239.

So for postal address N and local address 1 then set the total on the switches to N-1

Main Address Offset

SW2 Setting

Pos Subtract Pos Subtract

0Off* 8 28

1 0 9 32

2 4 A 36

3 8 B 40

4 12 C 44

5 16 D 48

6 20 E 52

7 24 F 56

Major Address Offset DIP SW3(1-2)

2 1 Offset

Off Off 0*

Off On 60

On Off 120

On On 180

Minor Address Offset DIP SW3(3-4)

4 3 Offset

Off Off 0*

Off On 1

On Off 2

On On 3

SW2

Shown at 0

SW3

(QWDF)

OFF ↔ ON

SW3

(ASER)

OFF ↔ ON

The number in this table is added to

the number in the table above t

determine the subtracted amount.

The number in this table is added to

the numbers in the tables above to

determine the subtracted amount

bellissimo BSSW Gate Controller

PD-120 Issue 1 Installation and Operating Manual Page 8 of 14

Troubleshooting

Common Faults

A very high percentage of calls to our technical support number, regarding new

installations, are resolved to faulty wiring. The reasons for these are various:-

Broken cores, especially short links, sometimes broken inside the insulation!

Connectors clamped onto the insulation instead of copper.

Wire in the wrong side of a rising clamp connection, the clamps need to be unscrewed

far enough to stop the wire going “underneath”.

Shorts or opens due to cables having been stapled or nailed through.

A common fault is wiring a connector left to right instead of right to left, or one or more

twisted pairs the wrong way round.

Tip. The heads of screws on connectors are not a reliable means of making a connection

with a meter, try pushing the probe into the wire entry point.

Quick Fault Reference

These tables provide a quick indication of the possible fault.

Call Problems

Local Block calls.  Data connection is directly wired from input to output

connector, so fault must be elsewhere or be a wiring fault

at the interconnections. Test by bypassing the BSSW.

Gate calls.  Eliminate other faults by debugging the local block first.

 Check the address translation if being used. Try

switching it off and calling using the actual phone

address. N.B. Ensure other blocks are temporarily

isolated from the gate to prevent multiple phones ringing.

 To check gate input, switch off address translation

(SW2=0) and move the input connector to the gate

connection. Make a block call.

Audio Problems

No audio from gate.  Broken wire or wiring fault on the audio pair from the gate.

Loud feedback at gate.  Open or short circuit on audio pair.

Audio fault from block.  Connection is direct from input to output connector, so

fault MUST be elsewhere or be a wiring fault.

Video Problems

No Video but calls are

otherwise OK.  Broken or shorted wiring.

Picture quality  Ensure that the terminators for the gate wiring are correct,

just the end of the cable run is terminated.

bellissimo BSSW Gate Controller

PD-120 Issue 1 Installation and Operating Manual Page 9 of 14

Specifications

BSSW Gate Controller

Size 185mm x 230mm x 42mm

Supply Voltage 10.8V min, 13.8V typical, 15V max

Current Consumption 70mA idle @13.8V, 180mA active

PS4 Power Supply

Size 236mm x 105mm x 81mm

Output Voltage (regulated) 13.5V d.c. min, 13.8V d.c. nom, 14.1V d.c. max

Output Current 3A continuous, 4A peak (5 minutes max)

Mains Supply Internal Fuse Not user replaceable

Supply Voltage 230V 50Hz nominal

Temperature Range 0 ºC to 50 ºC

340C Power Supply

Size 140mm x 60mm x 53mm

Output Voltage (regulated) 13.5V Min, 13.8V Nom, 14.1V Max

Output Current 1A continuous, 1.5A peak (5 minutes max)

Mains Supply Internal Fuse Not user replaceable

Supply Voltage 230V 50Hz nominal

Temperature Range 0 ºC to 50 ºC

840 Power Supply – Battery Backed

Size 350mm x 330mm x 80mm

Output Voltage (regulated) 13.5V Min, 13.8V Nom, 14.1V Max

Output Current 3A continuous, 4A peak (5 minutes max)

Mains Supply Internal Fuse T2A 20mm HBC (HRC) Ceramic

Battery Fuse F4A 20mm Glass

Supply Voltage 230V 50Hz nominal

Temperature Range 0 ºC to 50 ºC

bellissimo BSSW Gate Controller

PD-120 Issue 1 Installation and Operating Manual Page 10 of 14

Diagram A – bellissimo Gate and Block Wiring

Site Overview

A “Site” consist of 1 or more “Gates” and 2 or

more blocks.

The Cat5 from each “Gate” is daisy chained

around the blocks to ensure that video quality

is maintained. Different “Gates” may take

different routes, but aiming for the shortest

runs.

Gate Detail

A “Gate” consists of 1 or more panels and

associated controllers. For instance the

panels may consist of a lorry panel and a car

panel at a vehicle gate plus a pedestrian

panel for a pedestrian gate. These can be

grouped as a single logical “Gate”.

The controllers have to be within 50m of the

panels in an appropriately protected housing.

Block Detail

A “Block” may either be a physical building

with 1 or more entrances or just a logical

collection of flats which need their wiring

isolated.

Equipment consists of 1 BSSW, 1 or more

BSC4’s and 0 or more door controllers.

Block

Gate

Block

1 x Cat5

per Gate

1 x Cat5

Site

BSDx

Gate

To Block Two Panel

Gate Shown

BSSW

BSDx

BSC4

Gate

Inputs

Block

Further Door

Controllers

Further Video

Controllers

Andere Handbücher für bellissimo

Inhaltsverzeichnis

Andere Bell System Gegensprechanlage Handbücher

Bell System

Bell System bellissimo Bedienungsanleitung

Bell System

Bell System BSX Bedienungsanleitung

Bell System

Bell System bellissimo Bedienungsanleitung

Bell System

Bell System 500D Kurzanleitung

Bell System

Bell System 500D Bedienungsanleitung

Bell System

Bell System DAX Bedienungsanleitung

Bell System

Bell System DAX Bedienungsanleitung

Bell System

Bell System bellissimo Bedienungsanleitung

Bell System

Bell System bellview Bedienungsanleitung

Bell System

Bell System bell free Bedienungsanleitung

Bell System

Bell System 500A Kurzanleitung

Bell System

Bell System bellissimo Bedienungsanleitung

Bell System

Bell System bellfree BF Bedienungsanleitung

Bell System

Bell System 902 Bedienungsanleitung

Bell System

Bell System 719S Bedienungsanleitung

Bell System

Bell System Digibell Bedienungsanleitung

Bell System

Bell System 500X Series Kurzanleitung

Bell System

Bell System bell free Bedienungsanleitung

Bell System

Bell System 500A Bedienungsanleitung

Bell System

Bell System 2-72 Multi Way Bedienungsanleitung

Bell System

Bell System bellview Bedienungsanleitung

Bell System

Bell System bellissimo Bedienungsanleitung

Bell System

Bell System 9nn Series Bedienungsanleitung

Bell System

Bell System bellagio Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung

Bticino

Bticino Classe 300 Bedienungsanleitung

LG L5142 Bedienungsanleitung