Bellfires CLASSIC BELL SMALL 3 PF Leitfaden

Bell•res wishes you many cosy evenings with your new Bell•res gas •re

This document is an essential part of your gas •re.

Read it carefully before installation and maintenance

of the gas •re and keep it in a safe place!

INSTALLATION INSTRUCTIONS &

MANUAL FOR MAINTENANCE

CLASSIC BELL SMALL 3 PF

Gas •re with closed combustion system

Serial number:

Production date:

English

Installation instructions

BELLFIRES GAS FIRE WITH CLOSED COMBUSTION SYSTEM:

Classic Bell Small 3 PF (Premium Fire) (CLBS3 PF)

English

Installation instructions

English

Installation instructions

The installation must only be carried out by a

“Gas Safe Register” registered installation engineer.

IMPORTANT

CONTENTS

Page

1. INSTALLATION INSTRUCTIONS .............................................................. 7

2. MAINTENANCE ......................................................................................... 58

3. FAULTS ...................................................................................................... 60

4. DISMANTLING / ASSEMBLING OF THE GLASS,

THE REGULATOR AND BURNER ..

...

....................................

........

. 61

5. CONNECTING DIAGRAM .............................................................

.........

... 79

6. DIMENSIONS ............................................................................................ 80

7. TECHNICAL DETAILS/REGULATIONS .................................................... 82

8. REPLACEMENT PARTS LIST .................................................................. 84

9. DISPOSAL OF PACKAGING AND APPLIANCE ....................................... 87

English

Installation instructions

English

Installation instructions

1 INSTALLATION INSTRUCTIONS

1.1 GENERAL

The gas ﬁre must be positioned and connected as a “room sealed system” (balance

ﬂue) appliance by a “Gas Safe Register” registered gas installation engineer in

accordance with the following installation instructions, nationally and locally applicable

regulations (see “Technical Details/ Regulations” at the rear of this manual). If you have

any queries regarding the installation, please consult your local gas company.

Important: Before beginning the installation, check that the details on the

rating plate correspond to the gas type and pressure to which

the appliance will be connected.

The appliance is factory set to the correct nominal heat input. The pilot light is set to the

correct level of consumption.

Depending on the version requested, the appliance is delivered from the factory with a

Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm concentric connection for the removal of

the smoke gases and the supply of combustion air.

It is possible to install the gas ﬁre with either a wall or roof outlet.

The roof connection must be carried out using the concentric ﬂue system Ø100 mm -

Ø150 mm. The fumes are exhausted naturally to the outside environment through the

inner Ø100 mm pipe whereas the combustion air supply passes between the Ø100 mm

and Ø150 mm pipes.

The wall connection must be carried out using the concentric ﬂue system Ø130 mm -

Ø200 mm. The ﬂue gases are evacuated outside by means of natural draft through the

internal pipe of Ø130 mm, whereas the combustion air is supplied between the pipes of

Ø130 mm and Ø200 mm. The wall outlet itself is Ø100 mm - Ø150 mm.

The gas ﬁre can be installed in a completely sealed or mechanically ventilated house

without extra ventilation and/or fume extraction.

The gas ﬁre can be installed as an insertion into an existing open ﬁre place or as

a built-in appliance in a new ﬁre place.

In order to prevent the ﬁreplace heating up excessively, it must be properly

ventilated by installing vents at the top and bottom of the ﬁreplace.

If an existing chimney is to be used, please consult your installer ﬁrst. If the chimney

was previously used for a wood or coal ﬁre, then it should be cleaned by an expert.

English

Installation instructions

N.B. If any part is missing, please contact your dealer.

1.3 INCLUDED

Set documentation - Installation instructions & Manual for maintenance

- Instructions for Concentric Components

- Instructions for use & Manual daily maintenance

Attributes - Ceramic log set

- Fire glass “Black”

- Fire glass “Dark Amber”

- Embers

- Decorative ash

1.2 CONCENTRIC FLUE SYSTEMS Ø100 MM - Ø150 MM AND

Ø130 MM - Ø200 MM: • Bellﬁres - Muelink & Grol System

• Poujoulat - PGI Ssystem

• Ontop - Metaloterm US System

• Jeremias/STB - H-Twin System (STB = Chimney-

Technics Brummen NL)

• Jeremias - TWIN-GAS System

The gas ﬁre, in combination with the concentric ﬂue system [Ø100 mm - Ø150 mm]

and/or [Ø130 mm - Ø200 mm] (rigid and/or ﬂexible)

for the brand types mentioned

above, has been approved in accordance with the European CE-norm for gas

appliances and may therefore be used only with these systems.

The permitted components for these systems are listed in instructions enclosed:

CONCENTRIC COMPONENTS SUITABLE FOR THE INSTALLATION OF A

BELLFIRES GAS FIRE WITH CLOSED COMBUSTION. The guarantee on the

appliance lapses if it is installed, fully or partially, with other components or a different

ﬂue system.

The concentric ﬂue [Ø100 mm - Ø150 mm] and [Ø130 mm - Ø200 mm] systems can be

used with either a newly-built or existing chimney.

English

Installation instructions

1.4 OPTIONS AND ACCESSORIES

The following options and accessories can be supplied by your dealer:

Part no Option

Convection package Classic Bell Small 3

342397 • 1x Convection top plate

342398 • 1x Convection rear plate

324892 • 1x Convection set General

329708 Set high adjustable feet (4 pieces)

Part no Accessorie

324892 Convection set General: (for convection air extraction)

302188 • 2x Flexible aluminium pipe Ø125 mm, L= 3 m (max.)

310178 • 2x Fitting box 135 x 135 mm

309872 • 2x Convection exit grid, white, 145 x 145 mm

304040 • 4x Hose clamp Ø125 mm

329874 Set carrying brackets (2 pieces)

3........ Bellﬁres (M&G) concentric ﬂue system