Bellfires Smart Bell 65 MF Betriebsanleitung

Preparation manual

Smart Bell 65/60 MF

Serial number:

Production date:

This document or parts thereof may not be reproduced, stored in a retrieval system, or transmitted,

in any form or by any means, electronic, mechanical, photocopying, recording, nor otherwise,

without the prior written permission of Barbas Bellfires BV. This document could contain technical

inaccuracies or typographical errors. Barbas Bellfires BV reserves the right to revise this document

from time to time in the contents thereof.

Contact information

Barbas Bellfires BV

Hallenstraat 17, 5531 AB Bladel, The Netherlands

Phone: +31 49 733 9200

E-mail: [email protected]

Introduction

2Smart Bell 65-60

Contents

1 About this document................................................................................ 4

1.1 How to work with this document.................................................................................................. 4

1.2 Warnings and cautions used in this document............................................................................ 4

1.3 Related documentation................................................................................................................4

2 Overview of the concentric flue system................................................... 5

3 Safety.......................................................................................................6

3.1 Safety instructions for installation................................................................................................ 6

4 Requirements...........................................................................................7

4.1 Requirements on the location...................................................................................................... 7

4.2 Other requirements......................................................................................................................7

4.3 Requirements on the outlet..........................................................................................................7

4.3.1 Requirements on the roof outlet........................................................................................7

4.3.2 Requirements on the wall outlet........................................................................................8

4.4 Requirements on the concentric flue system...............................................................................9

4.4.1 Possibilities for a concentric flue system with a roof outlet............................................. 10

4.4.2 Possibilities for a concentric flue system with a wall outlet............................................. 15

5 Technical specification...........................................................................17

5.1 Dimensions Smart Bell 65/60 with a Built-in frame....................................................................17

5.2 Dimensions Smart Bell 65/60 with a Classic frame 35 mm....................................................... 18

5.3 Dimensions Smart Bell 65/60 with a Classic frame 52 mm....................................................... 19

5.4 Dimensions Smart Bell 65/60 with a Classic frame 70 mm....................................................... 20

5.5 Dimensions Smart Bell 65/60 with an Insert frame 15 mm........................................................21

5.6 Dimensions Smart Bell 65/60 with an Insert frame 50 mm........................................................22

5.7 Dimensions Smart Bell 65/60 with an Insert frame 50 mm and Convection fan........................23

5.8 Dimensions of the restriction plate.............................................................................................23

6 Available components for the concentric flue system............................ 24

6.1 Appliance part list.......................................................................................................................24

6.2 Bellfires - Muelink & Grol system Ø100 - Ø150......................................................................... 25

6.3 Poujoulat - DUOGAS system Ø100 - Ø150...............................................................................29

6.4 Ontop - Metaloterm US system Ø100 - Ø150............................................................................32

6.5 Jeremias/STB - H-Twin system Ø100 - Ø150............................................................................36

6.6 Jeremias - TWIN-GAS system Ø100 - Ø150.............................................................................40

Contents

Smart Bell 65-60 3

1 About this document

This document shows the necessary information to do these tasks on the Smart Bell

65/60 MF:

• Preparation for installation

This document refers to the Smart Bell 65/60 MF as 'the appliance'. This document is an

essential part of your appliance. Read it carefully before you do work on the appliance.

Keep it in a safe place.

The original instructions of the document are in English. All other language versions of

the document are translations of the original instructions. It is not always possible to

provide a detailed illustration of every single item of the equipment. The illustrations in

this document show a typical setup. The illustrations are for instructional use only.

1.1 How to work with this document

1. Make yourself familiar with the structure and content of the document.

2. Read the safety chapter in detail.

3. Make sure that you understand all the instructions.

4. Do the procedures completely and in the given sequence.

1.2 Warnings and cautions used in this document

Warning

If you do not obey these instructions, there is a risk that can cause personal injury or

death.

Caution

If you do not obey these instructions, there is a risk of damage to the equipment or to

property.

Note

A note shows more information.

Symbol Description

Visual sign that there is a hazard

Visual sign that there is a notice

1.3 Related documentation

• Preparation manual

• Installation and maintenance manual

• User manual

About this document

4Smart Bell 65-60

2 Overview of the concentric flue system

The concentric flue system provides the appliance with combustion air and removes the

flue gases from the appliance. The concentric flue system is made of these items:

Item Description

Concentric flue The concentric flue is a pipe with an inner pipe. The in-

ner pipe is used as flue gas channel and the space be-

tween the inner pipe and the outer pipe is used as

combustion air channel

Flue gas channel The flue gases from the appliance flow through the

channel to the outlet by a natural draft

Combustion air channel Supplies the appliance with fresh air from the outlet

through the channel

Outlet/terminal Entry for the combustion air channel and exit for the

flue gas channel

Overview of the concentric flue system

Smart Bell 65-60 5

3 Safety

3.1 Safety instructions for installation

Caution:

• The appliance must be installed as a 'room sealed system' appliance by a

certified and registered gas installation engineer in accordance with the

supplied installation instructions, and nationally and locally applicable

regulations.

• If you have any questions regarding the installation, consult your local gas

company.

• Only use items in the installation that are specified in this manual and the

related documents.

• Only use the following brands for the installation of the concentric flue

system:

Manufacturer system

Bellfires Muelink & Grol system

Poujoulat DUOGAS system

Ontop Metaloterm US system

Jeremias/STB (STB = Schoorsteen

Techniek Brummen NL)

H-Twin system

Jeremias TWIN-GAS system

• Do not use a combination of parts from different brands for the installation

of the concentric flue system.

• Before beginning the installation, check that the details on the rating plate

correspond to the gas type and supply pressure to which the appliance will

be connected.

Safety

6Smart Bell 65-60

4 Requirements

4.1 Requirements on the location

• Never use combustible building materials for the fireplace.

• Do not install the appliance against a flammable rear wall.

• Install a nonflammable insulation plate of at least 12 mm between the appliance and

the rear wall. The insulation plate must cover the entire area of the rear of the

appliance.

• The appliance must be installed approximately 2 cm from the rear wall.

• If the fire burns in the appliance, make sure that the floor temperatures below and in

front of the appliance cannot be higher than 85 °C .

• Make sure that the room where the appliance is installed is properly ventilated.

4.2 Other requirements

• The gas supply connection is located under in the appliance for an easy connection to

all directions.

• Only use gas piping of at least 1/2" and a shut-off valve to connect the gas supply to

the gas regulator block of the appliance.

• Make sure that there is a wall socket with earth connection nearby the appliance. The

socket must be accessible at all times. The powercable (+ 0.5 m) is coming from the

rear of the appliance.

• Install the fireplace on a solid floor that can bear the weight of the appliance and the

fireplace.

• If the floor is made of flammable material, take correct safety measures. Install a

temperature protection plate made of nonflammable material between the appliance

and the floor.

• The appliance must be installed into an existing open fireplace or as a built-in

appliance in a new fireplace.

• If the concentric flue system is installed in a chimney that is used for wood or coal fire,

clean the chimney.

• If you built a new fireplace, make sure that it is ventilated with vents at the bottom and

top of the fireplace. If the fireplace is not ventilated the temperature of the appliance

can increase to dangerous temperatures and damage the fireplace.

• Keep a minimum distance between the appliance and a front wooden ﬁreplace

surround; with a depth of less than 10 cm, of:

• 5 cm on the sides: (minimum distance: side appliance - leg wooden ﬁreplace

surround)

• 40 cm at the top: (minimum distance: top appliance - bottom of beam wooden

ﬁreplace surround) The temperature on the underside of the beam of the wooden

ﬁreplace must never exceed 85°C. Optional: insulate the bottom of the wooden

beam with a ﬁreproof plate.

4.3 Requirements on the outlet

4.3.1 Requirements on the roof outlet

Make sure that the outlet is installed at least 0.5 meter from the edge of the roof.

Note:

All the minimum distances are guidelines. Consult your national and local

directives for the exact minimum distances.

Requirements

Smart Bell 65-60 7

Location of any of the items(*) Minimum distance between the items

and the roof outlet

At the same roof as the outlet 3 m

At a different roof as the outlet 1 m

At a lower positioned wall than the outlet 1 m

At a higher sloping surface than the outlet 3 m

(*) Items:

• A ventilation opening that services an occupied room, a toilet or a bathroom.

• A combustibion air supply, if the supply flows through an occupied room.

• A window that can be opened that services an occupied room, a toilet or a bathroom.

4.3.2 Requirements on the wall outlet

Make sure that the outlet is installed at least 0.5 meter from:

• The corner of a building

• the edge of the roof

• The roof overhang and rain gutter

• Balconies etc. unless the exhaust construction extends to at least the face of the

protruding section

Note:

All the minimum distances are guidelines. Consult your national and local

directives for the exact minimum distances.

If the outlet is installed horizontally in less than 0.5 m and vertically in less than 2 m from

a public area, install an effective protector. Make sure that the mesh size of the guard

does not affect the operation of the appliance.

If the height of the outlet is less than 3 meter from the floor, the distance between the

outlet and a garden or a terrace must be at least 2 meter.

Location of any of the items(*) Minimum distance between the items

and the wall outlet

On a wall where the item services a living space other

than that of the owner of the fireplace.

Do not install the wall outlet under an

item.

On a wall (**)

• Below the item: 2 m

• Above the item: 0.75 m

• Left or right of the outlet: 0.75 m

within 1 meter of the roof overhang 2 m

Under a balcony, walkway, etc. 2 meter from the underside of the bal-

cony or walkway

Under a balcony, walkway, etc. if the outlet extends to the

front 2 m

A facing wall less than 2 meters from the outlet. Apply the minimum distance for items

on a wall.

(*) Items:

Requirements

8Smart Bell 65-60

• A ventilation opening that services an occupied room, a toilet or a bathroom.

• A combustion air supply, if the supply flows through an occupied room.

• A window that can be opened that services an occupied room, a toilet or a bathroom.

(**) If an obstruction protrudes at least 0.5 meter between the item and the outlet and the

obstruction has a lenght of at least the recommended minimum distance, ignore the

recommended minimum distance.

4.4 Requirements on the concentric flue system

Caution:

• Make sure that no flammable materials are located close to the flue

system. The outer walls of the flue system can be 150 °C.

• Make sure that the concentric flue system is in a casing.

• Make sure that the casing is made of heat resistant material.

• Make sure that air can flow in the casing. Use grates near the floor and

near the ceiling. Do this for every floor where the casing is located.

• Do not insulate the concentric flue.

The parts that are required for the installation of the concentric flue system are numbered

in the illustrations and refer to the part list in

Use the universal wall/floor support (number 36 in the part list) to attach the concentric

flue system to the casing and/or the floor.

Floor support Wall support

Install a concentric flue system as described in this section.

Some configurations of the concentric flue system require the installation of a flue

restriction plate. Different sizes of the flue restriction plate are delivered with the

appliance. Refer to the Installation and maintenance manual.

Requirements

Smart Bell 65-60 9

4.4.1 Possibilities for a concentric flue system with a roof outlet

Rigid concentric flue systems

4,28,(100)

10/11/12/13

(min. - max.)

Flue gas restriction plate width

Concentric connection on the appliance is

Ø100-Ø150 mm

2.0 - 4.0 m 30 mm

4.0 - 12.0 m 40 mm

Requirements

10 Smart Bell 65-60

Andere Handbücher für Smart Bell 65 MF

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bellfires Kamin im Innenbereich Handbücher

Bellfires

Bellfires Smart Bell 80 MF Bedienungsanleitung

Bellfires

Bellfires HORIZON BELL SMALLTUNNEL 3 Einrichtungshandbuch

Bellfires

Bellfires VENTO CLASSIC SMALL Installations- und Betriebshandbuch

Bellfires

Bellfires SMART BELL 90-80 PF Leitfaden

Bellfires

Bellfires Derby Einrichtungshandbuch

Bellfires

Bellfires Smart Bell 55 Betriebsanleitung

Bellfires

Bellfires VERTICAL BELL SMALL TUNNEL 3 CF Leitfaden

Bellfires

Bellfires UNICA-2 55 Installations- und Betriebshandbuch

Bellfires

Bellfires VIEW BELL XXL 3 LF Leitfaden

Bellfires

Bellfires UNICA-2 90 Installations- und Betriebshandbuch

Bellfires

Bellfires HORIZON BELL SMALLTUNNEL 3 Installations- und Betriebshandbuch

Bellfires

Bellfires Free Bell Einrichtungshandbuch

Bellfires

Bellfires VERTICAL BELL SMALL 3 CF Installations- und Betriebshandbuch

Bellfires

Bellfires SMART BELL 80 PF Leitfaden

Bellfires

Bellfires horizon bell xl 3 cf Bedienungsanleitung

Bellfires

Bellfires SMART BELL 80 Leitfaden

Bellfires

Bellfires SLIDE BELL 55 - 55 Einrichtungshandbuch

Bellfires

Bellfires horizon bell xl 3 cf Bedienungsanleitung

Bellfires

Bellfires UNC-2 40 Leitfaden

Bellfires

Bellfires RDL3 R LF Leitfaden

Bellfires

Bellfires Horizon Bell Large Tunnel 3 Installations- und Betriebshandbuch

Bellfires

Bellfires VIEW BELL TOPSHAM 3 CF Bedienungsanleitung

Bellfires

Bellfires SMART BELL 80-70 PF Installations- und Betriebshandbuch

Bellfires

Bellfires MEDIUM 3 CF/LF Leitfaden

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch