BEMIS 338 000 Leitfaden

Printed in U.S.A

READ AND SAVE THESE INSTRUCTIONS

586 4160 Rev. 4/04

French and Spanish

instructions included.

Se incluyen instrucciones

en Español y Francés.

Directives en français et

en espagnol comprises.

Evaporative

Humidifier

OWNERS

CARE

USE

MANUAL

Model:

338 000 3-speed Multiroom

Evaporative Humidifier with

Removable Water Bottles

and AirCare®Filter

SAVE THE ENVIRONMENT

RECYCLE APPROPRIATE MATERIALS

Patents: 5,037,583; 5,110,511; 5,133,904

Other Patents Pending

To order parts and accessories call 1-800 547-3888

336 500 3-speed Multiroom

Evaporative Humidifier with

Removable Water Bottles

and no AirCare®Filter

Important Safeguards

READ BEFORE USING YOUR HUMIDIFIER

1) This appliance has a polarized plug (one blade is wider than the other).

To reduce the risk of electric shock, this plug is intended to fit into a

polarized 120-volt AC, 15-amp outlet, only one way. If the plug does

not fit fully in the outlet, reverse the plug. If it still does not fit, contact a

qualified electrician. Do not attempt to defeat this safety feature. If an

extension cord must be used, it should also accept the wide blade plug

and meet this electrical rating.

2) Do not place the cord under rugs, in traffic areas, or near heat sources.

3) Do not use the humidifier if the cord is damaged.

4) Always unplug the power cord before cleaning, servicing,

or when the unit is not in use.

5) Unplug the humidifier and remove the water bottles before moving the

unit.

6) Do not place the humidifier near loose drapes, combustible materials, or

heat-producing objects.

7) Always place the humidifier on a hard, level surface where it will not be

accidentally bumped or tipped. Do not place on soft carpet.

8) DO NOT OPERATE THE HUMIDIFIER WITHOUT THE BASE ATTACHED.

9) This humidifier is UL listed with the Bemis by Essick Air brand evapora-

tive wicks in place. To maintain your UL rating, see your service center

for all repairs. To maintain your certified rating, use only Bemis by

Essick Air brand replacement wicks and chemicals. To order parts, wicks

and chemicals call 1-800-547-3888.

10)

Regular cleaning is recommended. Refer to the CARE & MAINTENANCE

section in the manual.

Introduction

This humidifier is designed to provide relief from dry air discomfort in local-

ized areas, such as bedrooms, dens and other rooms for a total area up to

1,100 square feet where humidity is needed. This product is not intended to

humidify a whole house.

Your Bemis by Essick Air evaporative humidifier adds invisible moisture to

your home by moving dry inlet air through saturated wicks. As air moves

through the wicks, the water evaporates into the air, leaving behind any

white dust, minerals or dissolved and suspended solids. Because the water is

evaporated, there is no messy mist or spray and no white dust, just clean and

invisible moist air.

As the evaporative wicks trap accumulated minerals from the water, their

ability to absorb and evaporate water decreases. We recommend changing

the wicks at least once a year, preferably disposing of the used wicks at the

end of the humidifying season and starting with new wicks at the beginning

of the next humidifying season. In hard water areas, more frequent replace-

ment may be necessary to maintain your humidifier’s efficiency.

Caution - We recommend using Bemis by Essick Air Bacteria

Treatment whenever you refill the water bottles to eliminate

bacteria growth. Follow the directions to determine the proper

amount to be added to the 1.6-gallon water bottles. The wicks

do not require the use of chelating agent type water treatments

that are intended for use in Rotobelt or Water Wheel type

humidifiers.

Tips for Best Performance

1) Do not block airflow inlets or outlets. Keep the grille areas clean.

2) Place the humidifier at least four inches away from any walls and in an

area away from heat registers.

3) Regular cleaning of the humidifier is recommended. Follow the CARE

AND MAINTENANCE instructions in this manual.

4) Replace the AirCare®(if provided) Filters regularly, preferably once a

year.

5) Change the evaporative wicks at least once a year. In extremely hard

water areas, more frequent replacement may be necessary. Only Bemis

by Essick Air wicks guarantee the rated output of your humidifier.

6) Use a bacteriostat, such as Bemis by Essick Air #1970 EPA Registered

Bacteria Treatment or Bemis by Essick Air #1970CN Environment

Protection Branch registered Bacteria Treatment (in Canada), whenever

you fill the water bottles to eliminate bacteria growth. To order AirCare®

Filters, evaporative wicks or Bacteria Treatment call 1-800-547-3888 or

use the convenient order form in the back of this manual.

7) Do not use water treatment products designed for Water Wheel,

Rotobelt, drum type, or ultrasonic humidifiers. These products may cause

the wicks to become inefficient.

Controls and Operation

1) Remove all packaging materials before operation.

2) The humidifier should be placed at least FOUR inches away from any

walls and away from heat registers. Do not place on soft carpet.

Unrestricted airflow into the unit will result in the best efficiency and per-

formance.

3) Refer to the operating controls. This model

has three motor speeds. Rotate the speed control

knob on the right to select the desired operating

mode. The faster the motor speed, the more air-

flow and the greater the amount of humidifica-

tion. The running time per filling varies with

humidity of the room, speed setting, and condi-

tion of the evaporative wick.

4) This model has a quiet LOW setting which reduces the airflow for

overnight operation in a bedroom or when conditions may not require

full output.

5) This model also has an automatic humidistat. (The humidistat control

knob is located on the left.) The humidistat will turn the humidifier on

when the relative humidity in your home is below the humidistat setting

and will turn the humidifier off when the relative humidity reaches the

humidistat setting. For initial operation, set the humidistat at its midpoint

and adjust up or down from there to achieve the desired humidity level.

6) Remove a water bottle, observe the water

bottle cap (A), and locate the valve stem mechanism (B).

The cap may be removed for filling and to provide easy

access for cleaning with a long soft brush. The valve

supplies a regulated amount of water to the water chan-

nel and wick. Do not attempt to increase water flow by

modifying this valve or adding additional holes to the

bottle. Doing so will invalidate your warranty and may

cause water damage to your home. NOTE: The water

level can easily be observed through the tinted water

bottle. It is time to refill the bottle when there is an inch

or less of water remaining in the water bottle.

Humidistat Speed Control

III

7) Before proceeding, make sure the wicks are

resting all the way into the water channel

(see diagram). Refer to the CARE AND

MAINTENANCE section for instructions on

removing the wicks for cleaning and service.

8) This model may include two (2) optional two-

stage air filters which attach to the inside of

the inlet grille area and clean the air as it

provides humidity. Refer to the CARE AND

MAINTENANCE section for instructions on installing and removing the

(2) two-stage air cleaning filters.

9) Take the water bottles to a sink, laundry basin, or bath tub. Use care in

handling the water bottles. Do not drop the bottles. They will break. Turn

bottle upside down and remove screw cap. Empty any remaining water

in bottle, rinse the bottle thoroughly, and wipe outside clean with a cloth

before adding fresh water.

10) To add water, carefull place the bottle in the sink or tub. Place on towel

to prevent scratches. Turn on the cold water tap and steady the bottle

while filling. Each bottle holds 1.6 gallons. Do not over fill. When full,

replace the screw cap and tighten securely. Place the bottle carefully on

a protected flat surface and wipe it dry with a soft cloth.

11) Return the bottle to its upright

position using the handle on the top

of the bottle. Slowly set the bottle in

the recessed area, the top of the bot-

tle flush with the top of the humidifier.

12) When positioned properly, the

valve will open and water will flow

into the water channel. The water

level will automatically remain at the

height of the pin in the water chan-

nel until water bottle is empty. It doesn't matter which bottle drains first.

13) Extend the power cord and inspect it for any damage. Do not use the

product if the cord has been damaged. Plug the cord into a polarized

120-volt AC outlet.

14) Adjust the speed control on the right to the desired position. You will feel

cool and invisible humid air exiting from the outlet grille. The outlet grille

is louvered and may be rotated 360 degrees to direct the airflow where

you want it.

Water Wicks

Air Filter

(one on each side)

FRONT

Caution: Under certain conditions, cold objects in the room, such

as windows and outside walls, may cause moisture to con-

dense. Severe condensation on window sills and walls may

result in water damage. When these conditions exist, a lower

speed setting is recommended. Note: The unit will not shut off

when the water bottles are empty; however, this will not dam-

age the humidifier.

Care and Maintenance

Humidifiers provide comfort by adding moisture to dry, heated, indoor air. To

get the most benefit from the humidifier and avoid product misuse, follow all

instructions carefully, specifically the operation, care and maintenance guide-

lines. Please note this is an electrical appliance and requires careful attention

when in use.

In addition, if you do not follow the recommended care and maintenance

guidelines, microorganisms may be able to grow in the water within the

humidifier’s reservoir.

CLEANING THE TRAY AND REPLACING THE (MODEL

#1040) WICKS

CAUTION: Disconnect the power cord before cleaning or servic-

ing the unit.

IMPORTANT: We recommend cleaning your humidifier at least

once a week. Follow instructions.

When carrying your humidifier, it must be kept level to avoid spilling the

water from the tray. ALWAYS carry the unit using the recessed handles on the

bottom of both sides of the tray. Remove and carry water bottles separately

from the tray.

Cleaning your humidifier regularly helps eliminate odors and bacterial and

fungal growth. Ordinary household bleach is a good disinfectant and can be

used in the humidifier tray and bottle after cleaning.

1) Turn off unit and unplug the cord.

2) Remove the water bottles from the humidifier, empty and place them in a

secure location.

3) Locate the two internal spring latches on the bottom center of each side

of the cover. Press inward while lifting up on the cover to release the

latch. Releasing these latches will allow removal of the top housing.

Place the top housing on a flat surface.

4) Remove the air cleaning filters (if provided) from the inlet grilles. See

CLEANING AND REPLACING THE AIR CLEANING FILTER.

REMOVING SCALE

5) Remove the two evaporative water

wicks from the tray allowing excess

water to drain into the tray. Rinse

the wicks under fresh water only.

Do not use soap, detergent, or any

other cleaners on the wicks. Leave

in the sink to drain.

6) Empty the water from the tray. Fill

the water tray and each water bot-

tle with one 8-oz. cup of undiluted

white vinegar. Let stand 20 minutes in supported upright position.

7) Swish the vinegar solution in the bottles, wetting all surfaces. Dampen a

soft cloth with undiluted white vinegar and wipe out the water tray to

remove scale. Do not use abrasive cleaners or cloths. Rinse the water

bottles and water tray thoroughly with fresh water to remove dissolved

scale and cleaning solution before disinfecting.

8) Clean dust from all interior surfaces with a soft dry brush. Clean the top

housing gently with a soft, dry cloth. Never use abrasive cleaners.

Inspect the air inlet and outlet grills. Clean the grille vents with a soft,

dry cloth or brush if they show accumulated dust.

DISINFECTING UNIT

9) Fill the water bottles and water tray with a solution of 1 teaspoon bleach

in 1 gallon of water. Let solution stand 20 minutes, swishing every few

minutes. Wet all surfaces.

10) Empty water bottles and water tray after 20 minutes. Rinse with water

until bleach smell is gone.

11) The outside of the water bottles may be wiped with a soft cloth damp-

ened with fresh water.

Spring Latches

RE-ASSEMBLY

12) Replace the wicks into the tray water channel. See CONTROLS AND

OPERATION section.

13) Replace the air filters (if provided) in the inlet grille by sliding the edge

of the filter into the slot on each side of the inlet grille.

14) Position the tray with the arrows on the inside of the tray pointing

toward you. Making sure the control knobs are facing toward you, posi-

tion the top housing directly above the tray. Lower it carefully onto the

tray and align the tray and top housing walls. The top housing latches

should snap into the shelf inside the tray and attach firmly to the tray.

With the latch on both sides of the cover in place, press down firmly on

top of the cover to secure the top housing latches to the tray. Lift the

housing slightly to be sure it is attached securely to the base. Failure to

do so may result in water damage to your home.

15) Return the humidifier to its desired location.

16) Refill and replace the water bottles. (Refer to the CONTROLS AND

OPERATIONS section.)

Under certain conditions, water impurities may accelerate bacteria

growth in the water bottle. We recommend using Bemis by Essick Air

Bacteria Treatment when the water bottles are filled. Follow directions on

the bacteriostat container.

17) Plug the unit in and turn it on.

REPLACING EVAPORATIVE WICKS AND AIR FILTERS

We recommend replacing the wicks at least once a season, more often in

hard water areas. When the wicks appear excessively clogged with mineral

deposits, discard them and restore your humidifier’s efficiency with new

wicks. Model #1040 is the replacement evaporative water wick and model

#1053 is the replacement air filter. (Call 1-800-547-3888 to order.)

Only Bemis by Essick Air filters guarantee the certified output of your humidi-

fier. Use of evaporative wicks other than Bemis by Essick Air evaporative

wicks will void your warranty as well as the certification of output and may

reduce the efficiency and output of your humidifier.

CLEANING AND REPLACING THE AIR CLEANING

FILTER (MODEL #1053) - IF PROVIDED

The air cleaning filter continuously removes particles and odor as the air in

the room is circulated during the normal operation of the humidifier. Over a

period of time, all the air in the room passes through and is cleaned by the

air filter.

Caution: Disconnect power before cleaning or servicing.

1) Turn the unit off and unplug

the cord.

2) Remove the water bottles from the

humidifier and lay bottles on their

backs.

3) Remove the top housing from the

tray. See Item 3 "CLEANING THE

TRAY."

4) Locate the air filters mounted above

the air inlet grille on both sides of

the humidifier. The air filters are flexible. Place a finger underneath the

bottom edge and slide filter out of the slots in the base. Pull it up and

out.

5) Inspect the air filters. The air filters are a

two-stage device. The fluffy white media is an

ELECTROSTATIC charged particulate filter for

removing dust and small particles. The black

inner media is an activated carbon filter for

removing odors.

6) Clean filters are important to maintain performance. Observe the

amount of contaminate on the white electrostatic side of the filter. If there

is a visible layer of dust accumulation, the filter should be cleaned or

replaced.

7) Replacing the air cleaning filters at least once each humidifying season

is recommended. The air filters may be gently cleaned with a soft-bristle

brush. Care should be used not to pull apart the bonded area around

the edge of the filter. Frequent cleaning will lengthen the life of the air

filter.

8) To replace the air filters, slip the side edges (white side up) into the slots

above the inlet grille.

END-OF-SEASON MAINTENANCE

Caution: Disconnect power before cleaning or servicing.

1) Follow weekly cleaning instructions when humidifier will not be used for

at least one week or more.

2) At the end of the humidification season, discard used evaporative wicks

and air cleaning filters.

3) Clean, disinfect and dry completely before storing. Do not store with

water inside water bottles or water tray. If used wicks are not being

replaced, run unit without water to dry wicks completely before storage.

4) Store in cool, dry location.

Air

Filters

5) Install new wicks and clean the humidifier before next season begins.

Use only Bemis by Essick Air evaporative wicks to ensure the manufac-

turer’s rated output for your humidifier. Use of a wick other than a Bemis

by Essick Air evaporative wick will void your warranty and may reduce

the efficiency and output of your humidifier. Call 1-800-547-3888 to

order. Alternatively, an order form is located in the back of this manual.

Troubleshooting

1. Unit does not operate at any speed setting:

• Polarized cord must be fully inserted in wall outlet. Turn the humidis-

tat control fully clockwise.

• Check the airflow path. Are there any obstructions preventing move-

ment of the fan blade?

• The motor contains a temperature-sensing fuse. If the motor becomes

overheated, the fuse may trip. Unplug the unit and contact the near-

est authorized service station. DO NOT ATTEMPT to repair the motor

yourself.

2. Not enough humidity:

• This is an evaporative humidifier. The humidity is invisible.

• The four open holes on the front of the cover are required for proper

humidistat operation. They must be kept unobstructed and clean.

• Check the condition of the evaporative wicks and the air cleaning fil-

ters. The evaporative wicks should be damp. If they are dry, refer to

the “Controls and Operation” section for the correct position of the

wicks. If the wicks are clogged, replace them.

• The water bottles may be empty – refill.

• The humidistat control may be set too low. Adjust the humidistat con-

trol clockwise to a higher setting.

3. Too much humidity:

• When condensation becomes heavy on cold surfaces in the room,

turn the unit to a lower speed setting, turn down the humidistat

(rotate counter-clockwise), or increase the room temperature.

4. Water does not flow out of the bottles:

• After refilling the water bottles and placing them in the humidifier,

water may not flow into the tray if the humidifier was run dry. Lift one

of the bottles several times so the valve opens and closes. This will

start the flow of water.

5. Water Bottle Leak:

• Bottle may be cracked.

• If the cap leaks after filling, remove the cap and inspect the bottle

rim and gasket. Wipe any mineral deposits off the bottle rim and the

cap gasket. Tighten the cap securely.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere BEMIS Luftbefeuchter Handbücher

BEMIS

BEMIS 726 000 Leitfaden

BEMIS

BEMIS 4D7 800 Leitfaden

Beliebte Luftbefeuchter Handbücher anderer Marken

Boneco

Boneco H300 Bedienungsanleitung

Bionaire

Bionaire CM1 Handbuch

Air-O-Swiss

Air-O-Swiss AOS 7131 Handbuch

KING

KING K 5002 Rainbow Bedienungsanleitung

Crane

Crane EE-6902 Bedienungsanleitung

Glaziar

Glaziar Ness Bedienungsanleitung

Philips

Philips DreamStation Go Abmessungen

Honeywell

Honeywell MISTMATE HUL520BC Bedienungsanleitung

Stadler Form

Stadler Form Hera Bedienungsanleitung

Hunter

Hunter 31206 Bedienungsanleitung

TaoTronics

TaoTronics TT-AH004 Bedienungsanleitung

adorini

adorini Cigar Heaven Bedienungsanleitung

Lanaform

Lanaform Aroma Bedienungsanleitung

Aprilaire

Aprilaire 800 Series Bedienungsanleitung

Pyle

Pyle SereneLife PHUMDIF8 Bedienungsanleitung

Trotec

Trotec B 200 Bedienungsanleitung

Pure Humidifier

Pure Humidifier EC Series Bedienungsanleitung

Crane

Crane EE-864 Bedienungsanleitung