Bench Dogs Quad MFT Hinge System Bedienungsanleitung

INSTRUCTION MANUAL

Quad MFT

Hinge System

WHAT’S IN THE KIT

1. HINGE ADAPTOR◄

2. ALIGNMENT ADAPTOR ◄

3. SPARE ORINGS 8X ◄

4. SPARE FIBRE WASHERS 2X M9.1MM ◄

5. QUAD BASE BOLTS◄

6. QUAD BASE ◄

7. HEX KEY ◄

8. TRACK BOLTS ◄

9. ALIGNMENT PIN ◄

10.TRACK BOLTS THUMB ◄

11. FIBRE WASHERS M8 ◄

12. HEX KEY ◄

FIND ALL INSTRUCTION MANUALS AT

WWW.BENCHDOGS.CO.UK

ALIGNMENT PIN PACK

CONTACT@BENCHDOGS.CO.UK WWW.BENCHDOGS.CO.UK Q E M

FOR MORE INFORMATION PLEASE VISIT

Locate the alignment adaptor

as pictured above

Using the supplied countersunk screws

place them in the countersunk holes (x2)

Thread into the quad bases (x2)

STEP 1 STEP 2 STEP 3

Instructions for MFT Hinge System

CONTACT@BENCHDOGS.CO.UK WWW.BENCHDOGS.CO.UK Q E M

FOR MORE INFORMATION PLEASE VISIT

Locate the Hinge adaptor plate Using the supplied countersunk screws

place them in the countersunk holes and

attach the quad bases like in previous

alignment adaptor instruction.

With your pre-drilled holes in your

MFT top, ensure the holes are a

maximum distance of 35mm from

the edge of the table. If using our

346 hole jig we advise the holes are

48mm from a row of holes.

STEP 5 STEP 6

Instructions for MFT Hinge System

STEP 4

48MM (using 346 hole jig)

35MM Maximum

Locate and Insert the hinge adaptor

plate into the 2x 20mm holes.

Using the supplied hex key tighten the quad

bases evenly until solid and no movement is

made with the hinge system.

STEP 7 STEP 8 STEP 9

CONTACT@BENCHDOGS.CO.UK WWW.BENCHDOGS.CO.UK Q E M

FOR MORE INFORMATION PLEASE VISIT

Instructions for MFT Hinge System

CONTACT@BENCHDOGS.CO.UK WWW.BENCHDOGS.CO.UK Q E M

FOR MORE INFORMATION PLEASE VISIT

Locate and Insert the hinge support

plate into the 2 x 20mm holes.

Using the supplied hex key

tighten the quad bases evenly

until solid and no movement is

made with the hinge system.

STEP 11

Instructions for MFT Hinge System

STEP 10

Using the supplied track bolts insert these

into the labelled track brand holes

(FMTE - Festool Makita Triton and Evolution)

STEP 12

Using the supplied bre washers, attach

the track bolt with the knurled female

thumbscrew. Ensure there is play left to

allow the track to slide in.

CONTACT@BENCHDOGS.CO.UK WWW.BENCHDOGS.CO.UK Q E M

FOR MORE INFORMATION PLEASE VISIT

Instructions for MFT Hinge System

STEP 14 STEP 15STEP 13

Set the 2nd Track bolt with the knurled

female thumbscrew.

Ensure there is play left to allow the

track to slide in.

CONTACT@BENCHDOGS.CO.UK WWW.BENCHDOGS.CO.UK Q E M

FOR MORE INFORMATION PLEASE VISIT

Slide the track bolts into the track.

Instructions for MFT Hinge System

Line up the edge of the track with the

edge of the hinge plate

Locate the supplied alignment pin which ts

your brand of track, this was selected when

purchasing your system.

STEP 17 STEP 18STEP 16

CONTACT@BENCHDOGS.CO.UK WWW.BENCHDOGS.CO.UK Q E M

FOR MORE INFORMATION PLEASE VISIT

Instructions for MFT Hinge System

Check hinge lifts into a vertical position and

stays in place with the hinge in its upright or

lowering position, there will be some lateral

movement this is normal and will not move

once located in the alignment pin

Adjust tension to achieve the desired

force to allow the track to hold itself

STEP 20 STEP 21STEP 19

Insert this in the hole in line with the brand

you have ordered (FMTE - Festool Makita

Triton and Evolution)

CONTACT@BENCHDOGS.CO.UK WWW.BENCHDOGS.CO.UK Q E M

FOR MORE INFORMATION PLEASE VISIT

When lowering the track ensure the

track locates in the pin as shown above

STEP 22 FINAL SET UP

Instructions for MFT Hinge System

Inhaltsverzeichnis

Beliebte Zubehör für Elektrowerkzeuge Handbücher anderer Marken

Bosch

Bosch OSC004 Bedienungsanleitung

Rockler

Rockler 57510 Bedienungsanleitung

Bosch

Bosch RA1054 Montageanleitung

Grizzly

Grizzly T10808 Bedienungsanleitung

Kitagawa

Kitagawa SC N Series Bedienungsanleitung

Wolfcraft

Wolfcraft FKS 145 Kurzanleitung

ADAMAS

ADAMAS B32 Bedienungsanleitung

STEINEL PROFESSIONAL

STEINEL PROFESSIONAL 4007841009595 Bedienungsanleitung

Echo

Echo Speed-Feed Universal 400 LH/RH Bedienungsanleitung

SCHUNK

SCHUNK ROTA TB-TBS-EP Gebrauchsanweisung

Schmid

Schmid RAPID Secure XL Bedienungsanleitung

Drill Master

Drill Master 360X Bedienungsanleitung

Toro

Toro 138-5050 Bedienungsanleitung

jbc

jbc SF-SD Bedienungsanleitung

Bosch

Bosch GTA 3800 Professional Montageanleitung

RG AVAK

RG AVAK MaxDrill Series Bedienungsanleitung

infaco

infaco PW3 Bedienungsanleitung

Gloria

Gloria CUT & BRUSH Bedienungsanleitung