Bend-Pak HD-14T Bedienungsanleitung

1645 Lemonwood Dr.

Santa Paula, CA 93060 USA

Toll Free: (800) 253-2363

Tel: (805) 933-9970

bendpak.com

HD-14T Four-Post Lift

Installation and Operation Manual

Manual P/N 5900037 — Manual Revision F — February 2022

Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.

⚠

DANGER

IMPORTANT SAFETY INSTRUCTIONS,SAVE THESE

INSTRUCTIONS!

Save these instructions! Read the

entire

contents of this manual

before

using this product. Failure to

follow the instructions and safety precautions in this manual can

result in serious injury or death. Make sure all other operators also

read this manual. Keep the manual near the product for future

reference.

By proceeding with installation and operation, you

agree that you fully understand the contents of this manual

and assume full responsibility for product use

Models:

•HD-14T

Manual. HD-14T Four-Post Lift, Installation and Operation Manual, Manual P/N 5900037, Manual Revision F,

Released February 2022.

agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain

any rights to this content, and you will not use the copies for commercial purposes.

Trademarks. BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company,

product, and service names are used for identification only. All trademarks and registered trademarks mentioned

in this manual are the property of their respective owners.

Limitations. Every effort has been made to make sure complete and accurate instructions are included in this

manual. However, product updates, revisions, and/or changes may have occurred since this manual was

published. BendPak reserves the right to change any information in this manual without incurring any obligation for

equipment previously or subsequently sold. BendPak is not responsible for typographical errors in this manual.

You can always find the latest version of the manual for your product on the BendPak website.

Warranty. The BendPak warranty is more than a commitment to you: it is also a commitment to the value of

your new product. Contact your nearest BendPak dealer or visit www.bendpak.com/support/warranty for

full warranty details.

Safety.Your product was designed and manufactured with safety in mind. However, your safety also depends

on proper training and thoughtful operation. Do not install, operate, maintain, or repair the unit without reading and

understanding this manual and the labels on the unit;

do not use your Lift unless you can do so safely!

Owner Responsibility. In order to maintain your product properly and to ensure everyone’s safety, it is the

responsibility of the product owner to read and follow these instructions:

• Follow all installation, operation, and maintenance instructions.

• Make sure product installation conforms to all applicable local, state, and federal codes, rules, and regulations,

such as state and federal OSHA regulations and electrical codes.

• Read and follow all safety instructions; keep them readily available for operators.

• Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised.

• Do not operate the product until you are certain that all parts are in place and operating correctly.

• Carefully inspect the product on a regular basis and perform all maintenance as specified.

• Service and maintain the unit with approved replacement parts only.

• Keep instructions permanently with the product

and make sure all labels are clean and visible.

•

Only use the Lift if it can be used safely!

Unit Information. Enter the Model Number, Serial

Number, and the Date of Manufacture from the label

on your unit. This information is required for part or

warranty issues.

Model:

Serial:

Date of Manufacture:

HD-14T Four Post Lift 3P/N 5900037 — Rev. F — February 2022

Table of Contents

Introduction 3 Operation 61

Shipping Information 4 Maintenance 64

Safety Considerations 4 Troubleshooting 66

Components 7 Wiring Diagrams 67

Specifications 9 Labels 68

FAQs 11 Parts Drawings 71

Installation Checklist 12 ALI Store 74

Installation 13 Maintenance Log 75

Introduction

This manual describes the following BendPak Four-Post Lift:

•HD-14T. Four-Post Lift with an overall width of 127.5" / 3,239 mm raising Vehicles up to

14,000 lbs. (6,350 kg).

This manual is mandatory reading for all users of the HD-14T, including anyone who

installs, uses, maintains, repairs, or wants to know more about them.

Keep this manual on or near the equipment so that anyone who uses or services it can read it. If you

are having issues, refer to the Troubleshooting section of this manual for assistance.

⚠DANGER Use care when installing, operating, maintaining, or repairing this equipment; failure to

do so could result in property damage, product damage, injury, or in very rare cases,

death. Make sure only authorized personnel operate this equipment. All repairs must

be performed by an authorized technician. Do not make modifications to the unit; this

voids the warranty and increases the chances of injury or property damage. Make

sure to read and follow the instructions in this manual and on the labels on the unit.

Technical support and service is available from your dealer, on the Web at bendpak.com/support,

by email at support@bendpak.com, or by phone at (800) 253-2363, extension 196.

You may also contact BendPak for parts replacement information at (800) 253-2363, extension

191; please have the model and serial number of your unit available.

HD-14T Four Post Lift 4P/N 5900037 — Rev. F — February 2022

Shipping Information

Your equipment was carefully checked before shipping. Nevertheless, you should thoroughly inspect

the shipment

before

you sign to acknowledge that you received it.

When you sign a bill of lading, it tells the carrier that the items on the invoice were received in good

condition.

To protect yourself, do not sign until

after

you have inspected the shipment.

If any of

the items listed on the bill of lading are missing or are damaged, do not accept the shipment until the

carrier makes a notation on the bill of lading that lists the missing and/or damaged goods.

If you discover missing or damaged goods

after

you receive the shipment and have signed the bill of

lading, notify the carrier at once and request the carrier to make an inspection. If the carrier will not

make an inspection, prepare a signed statement to the effect that you have notified the carrier (on a

specific date) and that the carrier has failed to comply with your request.

It is difficult to collect for loss or damage after you have given the carrier a signed bill of lading. If this

happens to you, file a claim with the carrier promptly. Support your claim with copies of the bill of

lading, freight bill, invoice, and photographs, if available.

Our willingness to assist in helping

you process your claim does not make us responsible for collection of claims or

replacement of lost or damaged materials.

Safety Considerations

Read this entire manual carefully before installing or using the product.

Do not

install or operate the product until you are familiar with all operating instructions and warnings. Do not

allow anyone else to operate it until they are familiar with all operating instructions and warnings. Keep

this manual on or near the product for future reference.

Read and follow the warnings and instructions on the labels on the product. Contact BendPak at

(800) 253-2363 extension 191, or email support@bendpak.com if you need replacement labels

or a replacement manual.

⚠WARNING California Proposition 65. This product can expose you to chemicals including

styrene and vinyl chloride which are on the list of over 900 chemicals identified by

the State of California to cause cancer, birth defects or reproductive harm. Always

use this product in accordance with BendPak’s instructions. For more information,

visit www.p65warnings.ca.gov.

Important Safety Information

When using this equipment, basic safety precautions should always be followed, including:

•Read and understand all safety warning procedures before operating the Lift.

•Only operate your Lift between temperatures of 41°F to 104°F (5°C to 40°C).

•Make sure the all operators read and understand this Installation and Operation Manual.

Keep

the Manual near the Lift at all times

•The product may only be operated by authorized, trained persons. Keep children and untrained

personnel away from the Lift.

•Do not make any modifications to the Lift; this voids the warranty and increases the chances of

injury or property damage. Use only the manufacturer’s recommended attachments.

•

Never

exceed the rated capacity of the Lift.

HD-14T Four Post Lift 5P/N 5900037 — Rev. F — February 2022

•While the Lift is in use, keep all body parts well away from it.

•You

must

wear OSHA-approved (publication 3151) personal protective equipment at all times

when installing, using, maintaining, or repairing the Lift: leather gloves, steel-toed work boots, eye

protection, back belts, and hearing protection are

mandatory

•Do not use the Lift while tired or under the influence of drugs, alcohol, or medication.

•Care must be taken as burns can occur from touching hot parts.

•Do not operate equipment with a damaged power cord or if the equipment has been dropped or

damaged – until it has been examined by a qualified service person.

•Do not let a cord hang over the edge of a table, bench, or counter or come in contact with hot

manifolds or moving fan blades.

•If an extension cord is necessary, a cord with a current rating equal to or more than that of the

equipment should be used. Cords used for less current than the equipment may overheat. Care

should be taken to arrange the cord so that it will not be tripped over or pulled.

•Always unplug equipment from electrical outlet when not in use. Never use the cord to pull the plug

from the outlet. Grasp plug and pull to disconnect.

•To reduce the risk of fire, do not operate equipment in the vicinity of open containers of flammable

liquids (gasoline).

•To reduce the risk of electric shock or fire, never overload receptacles. Refer to the labels for the

proper load on receptacles.

•Adequate ventilation should be provided when working on operating internal combustion engines.

•To reduce the risk of electric shock, do not use on wet surfaces or expose to rain.

•BendPak recommends referring to the ANSI/ALI ALIS Standard (Current Edition) Safety

Requirements for Installation and Service for more information about safely installing, using, and

servicing your Lift.

•Always wear safety glasses! Everyday glasses only have impact resistant lenses, they are not

safety glasses.

•Let equipment cool completely before putting away. Loop cord loosely around equipment when

storing.

•Make an inspection of the Lift

before

using it. Check for damaged, worn, or missing parts. Do not

use it if you find any of these issues. Instead, take it out of service, then contact an authorized

repair facility, your dealer, or BendPak at (800) 253-2363 or support@bendpak.com.

•BendPak recommends making a

thorough

inspection of the product at least once a year.

Replace any damaged or severely worn parts, decals, or warning labels.

•The Lift uses electrical energy; if your organization has Lockout/Tagout policies, make sure to

implement them after connecting the Lift to a power source.

•When handling the Hydraulic components, always wear safety gloves! In rare cases, a

needle-like stream of Hydraulic Fluid (even at low pressure) can penetrate fingers, hands, or arms.

Such a puncture can feel like a bite, electric shock, or a prick. While it may seem like a minor issue,

any amount of Hydraulic Fluid injected into the human body is a serious issue. Anyone suffering

such a puncture wound should be immediately taken as an emergency to the hospital to

determine the extent of the injury. Explain the circumstances of the injury to the attending

physician, including what type of Hydraulic Fluid was involved. Do not assume a puncture wound

that could have been caused by Hydraulic Fluid is a minor issue; it could be life-threatening.

Save these instructions!

HD-14T Four Post Lift 6P/N 5900037 — Rev. F — February 2022

Symbols

Following are the symbols used in this manual:

⚠DANGER Calls attention to an immediate hazard that will result in death or severe injury.

⚠WARNING Calls attention to a hazard or unsafe practice that could result in death or severe

personal injury.

⚠CAUTION Calls attention to a hazard or unsafe practice that could result in minor personal

injury, product damage, or property damage.

NOTICE Calls attention to a situation that, if not avoided, could result in product or property

damage.

Liability Information

BendPak Inc. assumes no liability for damages resulting from:

• Use of the equipment for purposes other than those described in this manual.

• Modifications to the equipment without prior, written permission from BendPak.

•Injury or death caused by modifying, disabling, overriding, or removing safety features.

• Damage to the equipment from external influences.

• Incorrect operation of the equipment.

HD-14T Four Post Lift 7P/N 5900037 — Rev. F — February 2022

Components

HD-14T Four Post Lift 8P/N 5900037 — Rev. F — February 2022

The main components of your HD-14T Lift include:

•Power Post. The Post that holds the Power Unit.

The Power Post can be in either of two

locations

. You can tell the Power Post from the other Posts because it has two Mounting

Brackets on it. Mount the Power Unit on one of the two Mounting Brackets.

•The other three Posts. These Posts are interchangeable.

•Power Unit. An electric/hydraulic unit that connects to an electric power source and then

provides Hydraulic Fluid to the Hydraulic Cylinder that raises and lowers the Runways.

•Powerside Runway. On the same side as the Power Post. The Powerside Runway has the

Hydraulic Cylinder and the Lifting Cables under them. The Powerside Runway

must

go next to the

Power Post.

•Offside Runway. The other Runway. It does not have a Hydraulic Cylinder or Lifting Cables

underneath it.

•Flex Tube. Not shown. A flexible, black tube that attaches to an opening on the Powerside

Runway on one end and to the bottom of the Flex Tube Bracket Plate (near the Power Unit) on the

other end. Used for routing the Air Line, Return Line, and Hydraulic Hose to the Power Unit.

•Utility Rails. Hold the optional Rolling Jacks. Utility Rails

must

face the inside of the Lift.

•Crosstubes. One at each end of the Lift. The Crosstubes are hollow; the Lifting Cables that raise

and lower the Runways are routed through the Crosstubes. The Crosstubes are not

interchangeable; each Crosstube has an opening (called a ‘Window’) that faces the inside of the

Lift.

Make sure to install the Lift so that the

Windows open to the inside of the Lift

only

•Drive-up Ramps. One for each Runway. Use them to drive onto and off of the Runways.

•Tire Stops. Located at the Front of the Lift, Tire Stops prevent the Vehicle’s Front Tires from

going any further forward. Additionally, we strongly recommend chocking the Vehicle’s Rear Tires.

•Safety Locks. Once engaged, they hold the Runways in position, even if the power goes out or

there is a leak in the Hydraulic Hoses.

Only leave the Runways on the ground or

engaged on a Safety Lock.

•Pushbutton Air Valve. Includes a Pushbutton that moves the Safety Locks away from the

Ladder so that they do not engage as you lower the Runways. Used only to lower the Runways.

Located next to the Power Post.

•Safety Ladders. Part of the Safety Lock System installed at the back of the Post, somewhat

resembles a Ladder.

HD-14T Four Post Lift 9P/N 5900037 — Rev. F — February 2022

Specifications

HD-14T Four Post Lift 10 P/N 5900037 — Rev. F — February 2022

Model HD-14T

Lifting Capacity 14,000 lbs. / 6,350 kg

Max capacity at Front Axle 7000 lbs. / 3175 kg

Max capacity at Rear Axle 7000 lbs. / 3175 kg

aMin. runway height 7.5" / 194 mm

bMaximum rise 82" / 2,083 mm

cMaximum lifting height 86.5" / 2,197 mm

dOverall width1127.5" / 3,239 mm

d1: 126 / 3,200 mm

eOutside length 205" / 5,205 mm

fOverall length 234" / 5,927 mm

gHeight of post 101" / 2,543 mm

hDistance between posts 115.5" / 2,938 mm

iDrive-thru clearance 98" / 2,482 mm

jRunway width 20" / 508 mm

kRunway length 195" / 4,953 mm

lWidth between runways 34.5" or 41.5" / 876 – 1,054 mm

mRunway centerline 54.5" or 61.5" / 1,384 or 1,562 mm

nOutside edge of runways 74.5" or 81.5" / 1,892 or 2,071 mm

Min. wheelbase @ rated capacity2135" / 3,429 mm

Min. wheelbase @ 75 capacity2115" / 2,921 mm

Min. wheelbase @ 50 capacity2100" / 2,540 mm

Min. wheelbase @ 25 capacity280" / 2,032 mm

Maximum operating pressure 2,250 PSI

Safety Lock positions 17, spaced every 4" / 102 mm

Lifting time 65 seconds

Motor3 220 VAC, 60 Hz, Single Phase

1 Overall Width is defined as the dimension outside to outside of the Baseplates. Use d1 measurement

listed above for creating Chalk Lines. The dmeasurement above includes the Bolt heads that stick out

near the bottom of the Posts used for securing the Safety Ladders.

2 The Lift supports less weight than its rated capacity if the Vehicle’s wheelbase is shorter; this is because

the wheels are closer to the middle of the Runways, where there is less strength. For example, the

maximum weight allowed on the Lift for a Vehicle with a wheelbase of 100" is 50 percent of the Lift’s

rated capacity (or 7,000 lbs. when the rated capacity is 14,000 lbs.).

3 Special voltages available upon request.

Specifications subject to change without notice

Andere Handbücher für HD-14T

Inhaltsverzeichnis

Andere Bend-Pak Hebesystem Handbücher

Bend-Pak

Bend-Pak EV2400SL Bedienungsanleitung

Bend-Pak

Bend-Pak HD-14T Bedienungsanleitung

Bend-Pak

Bend-Pak SP-7XF Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10XLS-LP-181 Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10AXLS-LP Bedienungsanleitung

Bend-Pak

Bend-Pak GP-7 Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10XLS-181 Bedienungsanleitung

Bend-Pak

Bend-Pak PCL-18B Bedienungsanleitung

Bend-Pak

Bend-Pak PL-14000 Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-12CL Bedienungsanleitung

Bend-Pak

Bend-Pak HDS-35 Bedienungsanleitung

Bend-Pak

Bend-Pak HD-973P Bedienungsanleitung

Bend-Pak

Bend-Pak Clearfloor 10AP Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10AXLS Bedienungsanleitung

Bend-Pak

Bend-Pak xpR-10C Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10XLS-LP Bedienungsanleitung

Bend-Pak

Bend-Pak HDS-37 Bedienungsanleitung

Bend-Pak

Bend-Pak Clearfloor 10AP Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10AS Bedienungsanleitung

Bend-Pak

Bend-Pak HD-7ZM Bedienungsanleitung

Bend-Pak

Bend-Pak LR-10000 Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-9S Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-9 Bedienungsanleitung

Bend-Pak

Bend-Pak HD-973P Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung