Bend-Pak HD-9AE Bedienungsanleitung

INSTALLATION AND OPERATION MANUAL

RECEIVING

The shipment should be thoroughly inspected as soon as it

is received. The signed Bill of Lading is acknowledgement

by the shipping carrier as receipt of this product as listed

in your invoice as being in a good condition of shipment. If

any of these goods listed on this Bill of Lading are missing

or damaged, do not accept goods until the shipping carrier

makes a notation on the freight bill of the missing or dam-

aged goods. Do this for your own protection.

BE SAFE

Your new lift was designed and built with safety in mind.

However, your overall safety can be increased with proper

training and thoughtful operation on the part of the opera-

tor. DO NOT operate or repair this equipment without

reading this manual and the important safety instructions

shown inside. Keep this operation manual near the lift at

all times. Make sure that ALL USERS read and understand

this manual.

1645 Lemonwood Dr.

Santa Paula, CA. 93060, USA

Toll Free 1-800-253-2363

Tel: 1-805-933-9970

www.bendpak.com

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTAL-

LATION AND OPERATION. BY PROCEEDING WITH LIFT INSTALLATION

AND OPERATION YOU AGREE THAT YOU FULLY UNDERSTAND

AND COMPREHEND THE FULL CONTENTS OF THIS MANUAL.

FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO OPER-

ATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.

Manual Revision D6 - March 2020

Manual Part Number 5900175

9,000 POUND CAPACITY

COMMERCIAL GRADE

FOUR-POST LIFTS

MODELS:

HD-9AE

Keep this operation manual near the

machine at all times. Make sure that

ALL USERS read this manual.

400V 50Hz SUPPLY DETAILS ARE

INCLUDED WITH ELECTRICAL CON-

TROL BOX. DISREGARD SUPPLY WIR-

ING DETAILS IN THIS MANUAL

EUROPEAN USERS

ORIGINAL INSTRUCTIONS IN

ENGLISH LANGUAGE

9,000 POUND CAPACITY, COMMERCIAL GRADE

FOUR POST ALIGNMENT LIFT

This instruction manual has been prepared especially for you.

Your new lift is the product of over 40 years of continuous research, testing and development;

it is the most technically advanced lift on the market today.

READ THIS ENTIRE MANUAL BEFORE INSTALLATION & OPERATION BEGINS.

RECORD HERE THE LIFT AND

POWER UNIT INFORMATION WHICH IS LOCATED

ON THE SERIAL NUMBER

DATA PLATES ON THE LIFT AND

ON THE POWER UNIT

Power Unit Model # _____________

Power Unit Date Of Mfg. _____________

Power Unit Serial # _____________

Maximum Operating

Hydraulic Pressure 2,460 PSI

This information is required when

calling for parts or warranty issues.

PRODUCT WARRANTY

Our comprehensive product warranty means more than a commitment to you; it’s also a commitment to the value of

your new BendPak lift. For full warranty details and to register your new lift contact your nearest BendPak dealer or visit

http:/ / www.bendpak.com/ support/ warranty/

NOTE:

Every e󰀨ort has been taken to ensure complete and accurate instructions have been included in this manual, however, possible prod-

uct updates, revisions and or changes may have occurred since this printing. BendPak Ranger reserves the right to change specica-

tions without incurring any obligation for equipment previously or subsequently sold. Not responsible for typographical errors.

IMPORTANT NOTICE

Do not attempt to install this lift if you have never been

trained on basic automotive lift installation procedures.

Never attempt to lift components without proper lifting

tools such as a forklift or cranes. Stay clear of any mov-

ing parts that can fall and cause injury. These instruc-

tions must be followed to insure proper installation and

operation of your lift. Failure to comply with these instruc-

tions can result in serious bodily harm and void product

warranty. Manufacturer will assume no liability for loss or

damage of any kind, expressed or implied resulting from

improper installation or use of this product.

PLEASE READ ENTIRE MANUAL

PRIOR TO INSTALLATION.

DEFINITIONS OF

HAZARD LEVELS

Identify the hazard levels used in this manual with the

following definitions and signal words:

DANGER !

Watch for this symbol as it means: Immediate hazards

which will result in severe personal injury or death.

WARNING !

Watch for this symbol as it means: Hazards or unsafe

practices which could result in severe personal

injury or death.

CAUTION !

Watch for this symbol as it means: Hazards or unsafe

practices which may result in minor personal injury,

product or property damage.

OWNER’S RESPONSIBILITY

To maintain the lift and user safety, the responsibility of

the owner is to read and follow these instructions:

t Follow all installation and operation instructions.

t Make sure installation conforms to all applicable Local,

State, and Federal Codes, Rules, and Regulations;

such as State and Federal OSHA Regulations and

Electrical Codes.

t Carefully check the lift for correct initial function.

t Read and follow the safety instructions. Keep

them readily available for machine operators.

t Make certain all operators are properly trained,

know how to safely and correctly operate the unit,

and are properly supervised.

t Allow unit operation only with all parts in place and

operating safely.

t Carefully inspect the unit on a regular basis

and perform all maintenance as required.

t Service and maintain the unit only with authorized or

approved replacement parts.

t Keep all instructions permanently with the unit and

all decals on the unit clean and visible.

BEFORE YOU BEGIN

NOTIFY THE CARRIER AT ONCE if any hidden loss or

damage is discovered after receipt and request the carrier

to make an inspection. If the carrier will not do so, prepare

a signed statement to the effect that you have notified the

carrier (on a specific date) and that the carrier has failed to

comply with your request.

IT IS DIFFICULT TO COLLECT FOR LOSS OR DAMAGE

AFTER YOU HAVE GIVEN THE CARRIER A CLEAR

RECEIPT. Support claim with copies of the bill of lad-

ing, freight bill, invoice, and photographs, if available.

BendPak’s willingness to assist in helping you process

your claim does not make BendPak responsible for collec-

tion of claims or replacement of lost or damaged materials.

TABLE OF CONTENTS

Contents Page No.

Warranty / Serial Number Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Definitions of Hazard Levels . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Owner’s Responsibility . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installer/Operator Agreement/ Protective Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Safety / Warning Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 1 / Selecting Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Step 2 / Floor Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Concrete Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Assembly View / Description of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Floor Plan / General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Step 3 / Post and Crosstube Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

Step 4 / Raising the Crosstubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13

Step 5 / Power Side Ramp Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14

Step 6 / Off Side Ramp Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Step 7 / Cable / Sheave Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17

Step 8 / Mounting the Hydraulic Power Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Step 9 / Routing Hydraulic Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-20

Step 10 / Routing Air Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21

Step 11 / Power Unit Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-24

Step 12 / Slack Safety Spring Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25

Step 13 / Lift Start-Up / Final Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-26

Step 14 / Anchoring the Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27

Step 15 / Installing Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Step 16 / Leveling / Synchronizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-28

Step 17 / Bleeding the Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Post Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Optional Equipment Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-30

Step 18 / Operation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Step 19 / Lift Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-33

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Wire Rope Inspection and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-40

Lubrications Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-44

Parts Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-47

Maintenance Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-50

Certicate of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

INSTALLER / OPERATOR

PLEASE READ AND FULLY

UNDERSTAND. BY PROCEEDING

YOU AGREE TO THE FOLLOWING.

t I have visually inspected the site where the lift is to

be installed and verified the concrete to be in good condi-

tion and free of cracks or other defects. I understand that

installing a lift on cracked or defective concrete could

cause lift failure resulting in personal injury or death.

t I understand that a level floor is required for proper

installation and level lifting.

t I understand that I am responsible if my floor is of

questionable slope and that I will be responsible for all

charges related to pouring a new level concrete slab if

required and any charges.

t I understand that BendPak lifts are supplied

with concrete fasteners meeting the criteria of the

American National Standard “Automotive Lifts - Safety

Requirements for Construction, Testing, and Validation”

ANSI/ALI ALCTV-2006, and that I will be responsible

for all charges related to any special, regional, struc-

tural, and/or seismic anchoring requirements specified

by any other agencies and/or codes such as the Uniform

Building Code (UBC) and/or International Building Code

(IBC).

t I will assume full responsibility for the concrete floor

and condition thereof, now or later, where the above

equipment model is to be installed. Failure to follow

Danger, Warning, and Caution instructions may lead to

serious personal injury or death to operator or bystander

or damage to property.

t I understand that BendPak lifts are designed to be

installed in indoor locations only. Failure to follow instal-

lation instructions may lead to serious personal injury or

death to operator or bystander or damage to property or

lift.

Failure to follow Danger, Warning, and Caution instruc-

tions may lead to serious personal injury or death to

operator or bystander or damage to property.

Please read the entire manual prior to installation.

Do not operate this machine until you have read and

have understood all of the Danger, Warning and Caution

alerts in this manual. For additional copies

or further information, contact:

BendPak Inc.

1645 Lemonwood Dr.

Santa Paula, CA. 93060

1-805-933-9970

www.bendpak.com

INSTALLER / OPERATOR

PROTECTIVE EQUIPMENT

Personal protective equipment helps makes installation

and operation safer, however, it does not take the place

of safe operating practices. Always wear durable work

clothing during any installation and/or service activity.

Shop aprons or shop coats may also be worn, however

loose-fitting clothing should be avoided.

Tight-fitting leather gloves are recommended to protect

the technician’s hands when handling parts. Sturdy leath-

er steel-toe work shoes and oil resistant soles should be

used by all service personnel to help prevent injury during

typical installation and operation activities.

Eye protection is essential during installa-

tion and operation activities. Safety glass-

es with side shields, goggles, or face

shields are acceptable. Back belts provide

support during lifting activities and are

also helpful in providing worker protection. Consideration

should also be given to the use of hearing protection if

service activity is performed in an enclosed area, or if

noise levels are high.

THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED

COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OR YOURSELF AND OTHERS

AND CAN CAUSE PERSONAL INJURY OR DEATH. READ AND FOLLOW ALL INSTRUCTIONS IN

THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

1. Carefully remove the crating and packing materials.

CAUTION! Be careful when cutting steel banding mate-

rial as items may become loose and fall causing personal

harm or injury.

2. Check the voltage, phase, and proper amperage

requirements for the motor shown on the motor plate.

Electrical work should be performed only by a certified

electrician.

IMPORTANT SAFETY INSTRUCTIONS

Read these safety instructions entirely. Do not attempt to install this lift if you have never been trained

on basic automotive lift installation procedures. Never attempt to lift components without proper lifting tools such as

forklift or cranes. Stay clear of any moving parts that may fall and cause injury. When using your garage equipment,

basic safety precautions should always be followed, including the following:

INTRODUCTION

1. READ AND UNDERSTAND all safety warning proce-

dures before operating lift.

2. KEEP HANDS AND FEET CLEAR. Remove hands and

feet from any moving parts. Keep feet clear of lift when low-

ering. Avoid pinch points.

3. KEEP WORK AREA CLEAN. Cluttered work areas invite

injuries.

4. Consider work area environment. Do not expose equip-

ment to rain. DO NOT use in damp or wet locations. Keep

area well lighted.

5. ONLY TRAINED OPERATORS should operate this lift.

All non-trained personnel should be kept away from work

area. Never let non-trained personnel come in contact with,

or operate lift.

6. USE LIFT CORRECTLY. Use lift in the proper manner.

Never use lifting adapters other than what is approved by the

manufacturer.

7. DO NOT override self-closing lift controls.

8. REMAIN CLEAR of lift when raising or lowering vehicle.

9. CLEAR AREA if vehicle is in danger of falling.

10. ALWAYS ENSURE that the safeties are engaged before

any attempt is made to work on or near vehicle.

11. DRESS PROPERLY. Non-skid steel-toe footwear is

recommended when operating lift.

12. GUARD AGAINST ELECTRIC SHOCK.

This lift must be grounded while in use to

protect the operator from electric shock.

Never connect the green power cord wire to

a live terminal. This is for ground only.

13. DANGER! The power unit used on this lift contains high

voltage. Disconnect power at the recepta-

cle before performing any electrical repairs.

Secure plug so that it cannot be acciden-

tally plugged in during service.

14. WARNING! RISK OF EXPLOSION. This equipment

has internal arcing or sparking parts which

should not be exposed to flammable

vapors. This machine should not be located

in a recessed area or below floor level.

15. MAINTAIN WITH CARE. Keep lift clean for better and

safer performance. Follow manual for proper lubrication

and maintenance instructions. Keep control handles and/or

buttons dry, clean and free from grease and oil.

16. STAY ALERT. Watch what you are doing. Use common

sense. Be aware.

17. CHECK FOR DAMAGED PARTS. Check for alignment

of moving parts, breakage of parts or any condition that may

affect its operation. Do not use lift if any component is broken

or damaged.

18. NEVER remove safety related components from the lift.

Do not use lift if safety related components are damaged

or missing.

19. Keep hair, loose clothing, fingers, and all parts of

body away from moving parts

20. Use only as described in this manual. Use only manu-

facturer’s recommended attachments

21. ALWAYS WEAR SAFETY GLASSES. Everyday eye-

glasses only have impact resistant lenses, they are not

safety glasses

22. SAVE THESE INSTRUCTIONS.

STEP 1

(Selecting Site)

Before installing your new lift, check the following.

1. LIFT LOCATION: Always use architects plans when

available. Check layout dimension against floor plan

requirements making sure that adequate space if avail-

able.

2. OVERHEAD OBSTRUCTIONS: The area where the

lift will be located should be free of overhead obstruc-

tions such as heaters, building supports, electrical lines

etc.

3. DEFECTIVE FLOOR: Visually inspect the site where

the lift is to be installed and check for cracked or defec-

tive concrete.

5. Lift is designed for INDOOR INSTALLATION ONLY.

Outdoor use is prohibited. Always follow warnings illus-

trated on equipment labels.

STEP 2

(Floor Requirements)

This lift must be installed on a solid level concrete

floor with no more than 3° of slope. Failure to do so

could cause personal injury or death.

A level floor is suggested for proper use and installa-

tion and level lifting. If a floor is of questionable slope,

consider a survey of the site and/or the possibility of pour-

ing a new level concrete slab.

t DO NOT install or use this lift on any asphalt surface

or any surface other than concrete.

t DO NOT install or use this lift on expansion seams

or on cracked or defective concrete.

t DO NOT install or use this lift on a second / elevated

floor without first consulting building architect.

t DO NOT install this lift outside. It is only approved for

indoor installations.

t Refer to ANSI/ALI ALIS Standard (R2015) Safety

Requirements for Installation and Service for more

information about safely installing your Lift.

CONCRETE SPECIFICATIONS

LIFT MODEL CONCRETE REQUIREMENTS

HD-9AE 4.25” Min. Thickness / 3,000 PSI

DANGER !

All models MUST be installed on 3,000 PSI concrete only

conforming to the minimum requirements shown above.

New concrete must be adequately cured by at least

28 days minimum.

IMPORTANT NOTICE !

These instructions must be followed to insure proper installation and operation of your lift. Failure

to comply with these instructions can result in serious bodily harm and void product warranty.

Manufacturer will assume no liability for loss or damage of any kind, expressed or implied resulting

from improper installation or use of this product.

PLEASE READ ENTIRE MANUAL PRIOR TO INSTALLATION !

t Rotary Hammer Drill or Similar

t 3/4” Masonry Bit

t Hammer

t 4 Foot Level

t Open-End Wrench Set: SAE /Metric

t Socket And Ratchet Set: SAE/ Metric

t Hex-Key / Allen Wrench Set

t Medium Crescent & Pipe Wrenches

t Torque Wrench

t Crow Bar

t Chalk Line

t Medium Flat Screwdriver

t Tape Measure: 25 Foot Minimum

t Needle Nose Pliers

TOOLS REQUIRED

An air supply (30 PSI Min / 3 CFM Min.) will be required for the safety-lock mechanisms. See Step 11.

IMPORTANT NOTE:

BendPak lifts are supplied with installation instructions and concrete fasteners meeting the criteria as prescribed

by the American National Standard "Automotive Lifts - Safety Requirements for Construction, Testing, and

Validation" ANSI/ALI ALCTV-2011. Lift buyers are responsible for any special regional structural and/or seismic

anchoring requirements specied by any other agencies and/or codes such as the Uniform Building Code (UBC)

and/or International Building Code (IBC).

When removing the lift from shipping angles, pay close attention as the ramps can slide and can cause injury.

Prior to removing the bolts make sure the ramps are held securely by a fork lift or some other heavy lifting device.

PARTS INVENTORY

Be sure to take a complete inventory of parts prior to beginning installation.

Description Qty

Small Window Crosstube 1

Large Window Crosstube 1

Power Post 1

Post 3

Off Side Ramp Assembly 1

Power Side Ramp Assembly 1

Drive-Up Ramps 2

Alignment Turnplate 2

Power Unit 1

Parts Box (Packing List Enclosed) 1

Parts Bag (Packaged in Part Box) 1

Power Post

Drive-Up

Ramp

Off Side Ramp

Assembly

Power Side

Ramp Assembly

Alignment

Turnplates

Post

Small Window

Crosstube

Large Window

Crosstube

FLOOR PLAN / GENERAL SPECIFICATIONS

HD-9AE

Lifting Capacity 9,000 lbs / 4082 Kg.

Max capacity / front axle 4,500 lbs. / 2,041 kg

Max capacity / rear axle 4,500 lbs. / 2,041 kg

A - Overall Width 127” / 3,226 mm

B - Outside Length 198” / 5,028 mm

C - Overall Length 224” / 5,695 mm

D - Height of Columns 88” / 2,232 mm

E - Min. Runway Height 6.9” / 125 mm

F - Max. Rise 70” / 1,778 mm

G - Max Lifting Height 76.9” / 1,953 mm

H - Width Between Columns 117” / 2,972 mm

I - Runway Width 19” / 483 mm

J - Width Between Runways(*) 40” / 1017 mm

K - Length of Runways 188.5” / 4788 mm

L - Min. 4- Wheel Alignment (**) 89.5” / 2275 mm

M - Max. 4 Wheel Alignment (**) 144.7” / 3675 mm

N - Max. 2 Wheel Alignment (**) 159.7” / 4056 mm

Min. wheelbase @ rated capacity: 135”/ 3429 mm

Min. wheelbase @ 75% capacity 115” / 2921 mm

Min. wheelbase @ 50% capacity 95” / 2413 mm

Min. wheelbase @ 25% capacity 80” / 2032 mm

Locking Positions 14

Lock Spacing Every 4” / 102 mm

Lifting Time 45 Seconds

Standard Motor (**) 220 VAC / 60Hz 1 Ph.

Emission sound pressure at Operator Position < 70 dB(A)

* This dimension may be limited with the addition of rolling jacks. See Rolling Jack Specications on Separate page.

** For CE compliant countries see errata sheet included with control panel.

The design, material and specications are subject to change without notice.

NOTE:

TO CHECK IF LIFT IS SQUARE, DIAGONAL MEASUREMENTS OF POSTS AS SHOWN ABOVE MUST BE EQUAL.

CLEARANCES

1. Lift Location: Use architects plan and Engineers

automatic level (transit) when available to locate lift. The

above shows clearances of a typical bay layout. Lift oor

area should be level.

2. Ceiling or overhead clearance must be 80” plus height

of tallest vehicle.

3. Estimating Column Shim requirements:

In the following section, the terms “highest” and “low-

est” refer to elevation of oor.

A. Mark locations where lift columns will be posi-

tioned in bay.

B. Place target on oor at column positions (NOT

on column base plates) and record readings.

C. Find the highest of the four locations. Find the

di󰀨erence between the readings at each of the re-

maining three columns and the highest reading.

D. The di󰀨erence is the estimated amount of shim

thickness needed at each column.

Note: Maximum shim thickness is 1/2” per column using

shims and anchors provided with lift.

If no transit is available, oor slope can be determined by

using a chalk line and level.

Andere Handbücher für HD-9AE

Inhaltsverzeichnis

Andere Bend-Pak Hebesystem Handbücher

Bend-Pak

Bend-Pak MDS-6EXT Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10AXLS-LP Bedienungsanleitung

Bend-Pak

Bend-Pak HDS-37 Bedienungsanleitung

Bend-Pak

Bend-Pak LR-60P Bedienungsanleitung

Bend-Pak

Bend-Pak PL-6KDT-S Bedienungsanleitung

Bend-Pak

Bend-Pak HDS-27X Bedienungsanleitung

Bend-Pak

Bend-Pak HDS-27 Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-9DT Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10XLS-LP-181 Bedienungsanleitung

Bend-Pak

Bend-Pak 5175153 Bedienungsanleitung

Bend-Pak

Bend-Pak HD-9STX Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-9FD Bedienungsanleitung

Bend-Pak

Bend-Pak LR-5T Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10AS Bedienungsanleitung

Bend-Pak

Bend-Pak xpR-10C Bedienungsanleitung

Bend-Pak

Bend-Pak HD-9ST Bedienungsanleitung

Bend-Pak

Bend-Pak MD-6XP Bedienungsanleitung

Bend-Pak

Bend-Pak PL-7000XR Bedienungsanleitung

Bend-Pak

Bend-Pak HDS-14 Bedienungsanleitung

Bend-Pak

Bend-Pak HDSO-14P Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-9F Bedienungsanleitung

Bend-Pak

Bend-Pak XPR-10AXLS Bedienungsanleitung

Bend-Pak

Bend-Pak PL-6000DC Referenzhandbuch

Bend-Pak

Bend-Pak HDS-18EA Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung