BenQ M73 Series Bedienungsanleitung

M73 Series

Network Projector

Operation Guide

V1.00

be reproduced, transmitted, transcribed, stored in a retrieval system or translated into

any language or computer language, in any form or by any means, electronic, mechanical,

magnetic, optical, chemical, manual or otherwise, without the prior written permission

of BenQ Corporation.

All other logos, products, or company names mentioned in this manual may be the

registered trademarks or copyrights of their respective companies, and are used for

informational purposes only.

Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any warranties,

merchantability or fitness for any particular purpose. Further, BenQ Corporation

reserves the right to revise this publication and to make changes from time to time in

the contents hereof without obligation of BenQ Corporation to notify any person of

such revision or changes.

This user manual aims to provide the most updated and accurate information to

customers, and thus all contents may be modified from time to time without prior

notice. Please visit http://www.benq.com for the latest version of this manual.

BenQ is not responsible for the content of the websites or of similar resources, which

are maintained and controlled by third parties, that may be linked from this product.

Providing links to those websites or to similar resources does not mean that BenQ

makes any warranty or representation to their content by expression or by implication.

Any third party content or service preinstalled in this product is provided "as is". BenQ

does not, by expression or by implication, make any warrant to the content or to the

services provided by third parties. BenQ does not warrant or guarantee that the

content or services provided by third parties are accurate, effective, most up-to-date,

legal, or complete. Under no circumstances shall BenQ be liable for the content or

services provided by third parties including their negligence.

Services provided by third parties may be terminated temporarily or permanently. BenQ

does not warrant or guarantee that the any content or services provided by third

parties are in good condition at any time, and is not liable for the termination of the said

content and services.

In addition, BenQ is not involved in any transactions you conduct in the websites or

similar resources maintained by third parties.

You should contact the content or service providers for any questions, concerns, or

disputes.

Table of contents

Preparation ......................................................................................5

Switching to Advanced Menu...............................................................5

Wired connections .....................................................................................6

Setting up a wired network for the projector........................................................6

Connecting your computer to the projector via a wired connection ..............7

Wireless connections.................................................................................8

Setting up a wireless network for the projector ...................................................8

Connecting your computer or mobile device to the projector wirelessly......9

Projecting via QCast (for PCs)................................................11

Minimum system requirements............................................................. 11

Prerequisite................................................................................................ 11

Downloading QCast..................................................................................................11

Installing QCast ..........................................................................................................11

Connecting your computer to the projector .......................................................12

Selecting Network Display in the input source menu ....................................12

Launching QCast ........................................................................................................12

Using QCast............................................................................................. 14

Role assignment ...........................................................................................................14

Network Display Code.........................................................................................15

Mirror Off / On / Extension......................................................................................15

Quality..........................................................................................................................16

Audio ............................................................................................................................16

Compatible ................................................................................................................17

Advanced ....................................................................................................................17

Preference..................................................................................................................21

Projecting via QCast (for mobile devices)............................22

Minimum system requirements............................................................. 22

Prerequisite................................................................................................ 22

Selecting Network Display in the input source menu ....................................22

Downloading QCast..................................................................................................22

Connecting your mobile device to the projector ................................................23

Launching QCast ........................................................................................................23

Using QCast ...............................................................................................26

Role assignment........................................................................................................... 26

Network Display Code ........................................................................................ 27

Mirror Off / Mirror On......................................................................................... 27

Photo............................................................................................................................ 28

Camera ....................................................................................................................... 28

Document.................................................................................................................. 28

Advanced.................................................................................................................... 29

Preference ................................................................................................................. 29

Managing the projector using a web browser ...................... 30

Supported web browsers........................................................................30

Configuring Standby Settings for the projector ...........................30

Accessing the BenQ Projector Control System .......................30

Main function................................................................................................................ 32

Accessing the Internet with a wireless

connection..................................................................................... 40

Accessing the Internet via QCast ........................................................40

Accessing the Internet via projector OSD..........................................40

PJLink commands......................................................................... 42

11/27/17

Preparation 5

Preparation

Your BenQ projector is equipped with wired and wireless network function. Via a network

connection you can project what is shown on your computer or mobile device’s screen

using the QCast app. You can also manage and control the projector from remote devices

such as desktops, laptops, tablets, and smartphones using web browsers.

In order to take advantage of these features, you need to complete the steps described in

the following sections. The basic workflow for projecting through a network is:

1. Set up a wired or wireless network for the projector.

See "Setting up a wired network for the projector" on page 6 or "Setting up a

wireless network for the projector" on page 8 for details.

2. Connect your computer or mobile device to the projector.

For wired connections, see "Connecting your computer to the projector via a wired

connection" on page 7 for details.

For wireless connections, see "Connecting your computer or mobile device to the

projector wirelessly" on page 9 for details.

3. Download QCast on your computer or mobile device.

For downloading QCast on your computer, see "Downloading QCast" on page 11

for details.

For downloading QCast on your mobile devices, see "Downloading QCast" on page

22 for details.

4. Project via QCast.

For using your computer to project via wired connections, see "Launching QCast"

on page 12 for details.

For using your computer to project via wireless connections, see "Launching QCast"

on page 12 for details.

For using your mobile device to project, see "Launching QCast" on page 23 for

details.

Switching to Advanced Menu

When you first enter the projector’s OSD menu, you will see the OSD’s Basic Menu.

Before you can configure the projector and network settings to use the features described

in this guide, you need to switch to the OSD’s Advanced Menu. Follow the steps below

to switch to the Advanced Menu:

1. Turn on the projector.

2. Press MENU to open the OSD’s Basic Menu.

3. Highlight Menu Type and press OK.

4. Highlight Advanced and press OK.

The OSD menu will now be set to the Advanced Menu which allows you to start

configuring the network settings.

After setting the Menu Type to Advanced, the Advanced Menu will be shown every time you

press the MENU button.

Preparation6

Wired connections

For projecting through a wired network, you need to connect the projector and your

device to the same local area network (LAN).

Setting up a wired network for the projector

If you are in a DHCP environment:

If your projector is in a DHCP environment, you do not have to manually set the IP

address. Follow the steps below to configure the wired network settings for the projector

in a DHCP environment:

1. Connect the projector to a local area network via an RJ45 cable.

2. Turn on the projector.

3. Press MENU to open the Advanced Menu.

4. Highlight Network and press OK.

5. Highlight Wired LAN and press OK.

6. Highlight DHCP and press OK.

7. Select On and press OK.

8. Highlight Apply and press OK.

9. Re-enter the Wired LAN page and check if the IP Address, Subnet Mask,

Default Gateway, and DNS Server have been automatically configured. Make

sure the Status is Connect.

If you are in a non-DHCP environment:

If your projector is in a non-DHCP environment, you need to manually set the IP Address,

Subnet Mask, Default Gateway, and DNS Server. Follow the steps below to configure the

wired network settings for the projector in a non-DHCP environment:

1. Repeat step 1 to 5 described in "If you are in a DHCP environment:" on page 6.

2. Highlight DHCP and press OK.

3. Select Off then press OK.

4. Contact your network administrator for information on the IP Address, Subnet

Mask, Default Gateway, and DNS Server settings.

5. Enter the projector’s IP Address, Subnet Mask, Default Gateway, and DNS

Server and assign the values as needed.

6. After finishing the settings, highlight Apply and press OK.

RJ45 cable

Laptop computer

Desktop computer

Projector

RJ45 cable

Wired LAN

Internet

If the IP Address still does not appear, contact your network administrator.

Preparation 7

Your projector is now connected to your local area network and can be accessed by any

devices linked to the same local area network.

Connecting your computer to the projector via a wired

connection

Follow the steps below to connect your computer to the projector through the local area

network:

1. Ensure the projector is connected to the local area network. You can enter the

Wired LAN page to check if the IP Address, Subnet Mask, Default Gateway,

and DNS Server are configured as needed and if the Status is Connect.

2. Connect your computer to the same local area network via an RJ45 cable.

Now your computer and the projector are on the same local area network.

Alternatively, to check the IP address of the projector, make sure the projector is connected to the

network, and press SOURCE on the projector and then select Network Display. The IP address

is displayed on the bottom left corner of the Network Display screen.

Your computer should be properly configured to detect a wired network connection. Check the

user manual of your computer or visit the manufacturer’s website for information on how to

configure a wired network connection.

Preparation8

Wireless connections

If you want to project wirelessly, you must first install the BenQ WDRT8192 USB wireless

dongle onto your projector. This USB wireless dongle is not shipped with your projector

and is sold separately. Do not install any other type of wireless dongle or module.

With the USB wireless dongle, your projector will be able to operate as a wireless LAN

access point (AP), allowing you to connect your computer or mobile device directly to this

ad hoc network. Furthermore, with the USB dongle installed, the projector can also

connect to your organization’s wireless network so that you can access the Internet while

projecting and making a presentation. See "Network Setup" on page 18 or "Accessing the

Internet with a wireless connection" on page 40 for details on accessing the Internet via a

wireless connection.

Setting up a wireless network for the projector

In order to use your projector wirelessly, follow the steps below:

1. Turn off the projector if it is powered on.

2. Insert the designated USB wireless dongle into the WIRELESS DONGLE port at

the rear of the projector.

3. Turn on the projector.

Projector

Wireless Dongle

Laptop computer Desktop computer

Smartphone

Tablet

• Never insert the dongle into the projector while the projector is powered on, as the network

connection may not be made properly.

• If you intend to re-insert the dongle during operation, power off the projector first.

The wireless dongle should only be installed into the WIRELESS DONGLE port. Installing the

dongle into the USB TYPE-A port on the projector will prevent the wireless dongle from

functioning.

Preparation 9

A wireless network for the projector will be set up automatically. The projector is now

operating as a wireless LAN access point and can be accessed wirelessly by your computer

or mobile device.

If you want to check the projector’s wireless network connection status, follow the steps

below:

1. Press MENU to open the Advanced Menu.

2. Highlight Network and press OK.

3. Highlight Wireless LAN and press OK.

4. Highlight Point to Point and press OK.

5. On the Point to Point page, make sure that Status is Connect, and that the

Network (SSID) information and IP Address are displayed.

Connecting your computer or mobile device to the

projector wirelessly

Follow the steps below to connect your computer or mobile device wirelessly to the

projector:

1. Make sure the BenQ USB wireless dongle has been properly inserted into the

WIRELESS DONGLE port at the rear of the projector.

2. Check the projector’s wireless network connection status. Go to the Point to

Point page, make sure the Network (SSID) has been set up and the Status shows

Connect.

3. Open the wireless menu of your computer or mobile device and search for the

available wireless networks.

4. Select the SSID of the projector.

5. Enter the login password to connect to the projector. You can find the password on

the (SSID) page.

• Network (SSID) is the projector’s ID used to identify the projector over the network and can be

modified. If you want to modify the SSID, select the Network (SSID) on the Point to Point

page and the (SSID) page will appear. On the (SSID) page, you can modify the projector’s

SSID. Select Commit to have the modifications take effect.

• The projector supports WPA2 security encryption.

• The SSID has a maximum length of 13 alphanumeric characters.

• The SSID and password can also be modified using a web browser. See "Network Settings" on

page 38 for details.

If your computer or mobile device cannot detect the wireless network, check the user manual of

your computer or mobile device or visit the manufacturer’s website for information on how to

connect to a wireless network.

Preparation10

Alternatively, to check the login passwords and SSID of the projector, make sure the USB wireless

dongle is properly connected to the projector, and press SOURCE on the projector. Select

Network Display. The SSID and password are displayed on the upper right corner of the screen.

Inhaltsverzeichnis

Andere BenQ Projektor Handbücher

BenQ

BenQ Portable Series Bedienungsanleitung

BenQ

BenQ MP721 - XGA DLP Projector Bedienungsanleitung

BenQ

BenQ W1120 Bedienungsanleitung

BenQ

BenQ MP620c Series Bedienungsanleitung

BenQ

BenQ MX520 Bedienungsanleitung

BenQ

BenQ MS560 Bedienungsanleitung

BenQ

BenQ MH680 Bedienungsanleitung

BenQ

BenQ MX813ST Bedienungsanleitung

BenQ

BenQ Home Entertainment I Series Bedienungsanleitung

BenQ

BenQ LX785 Bedienungsanleitung

BenQ

BenQ EX800ST Bedienungsanleitung

BenQ

BenQ Portable Series Bedienungsanleitung

BenQ

BenQ BH3020 Bedienungsanleitung

BenQ

BenQ X500i Bedienungsanleitung

BenQ

BenQ Home Entertainment W500 Bedienungsanleitung

BenQ

BenQ HT9050 Bedienungsanleitung

BenQ

BenQ MX503 Bedienungsanleitung

BenQ

BenQ Home Cinema Series Bedienungsanleitung

BenQ

BenQ Home Entertainment Series Bedienungsanleitung

BenQ

BenQ LU951ST Montage- und Bedienungsanleitung

BenQ

BenQ PB8250 - XGA DLP Projector Bedienungsanleitung

BenQ

BenQ PW9500 Bedienungsanleitung

BenQ

BenQ LK936ST Bedienungsanleitung

BenQ

BenQ Home Cinema Series Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung