BenQ SP0005 Bedienungsanleitung
FCC Warning
This equipment has been tested and found to comply with the limits for
Class A & Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with this user's guide, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
CE Mark Warning
This device complies with requirements of EN50081-1 and EN50082-1
under the scope of EMC Directive EEC.
Trademarks
Copyright ©2002 BenQ Corporation.
Contents subject to change without prior notice. BenQ is a registered
trademark of BenQ Corporation. All other trademarks belong to their
respective proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or by any
means or used to make any derivative such as translation, transformation,
or adaptation without permission from BenQ Corporation.
FCC_E.fm Page 1 Friday, August 9, 2002 5:33 PM
i
Ta b l e o f C o n t e n t s
1. Introduction ......................................................................... 1
1.1. Product Overview ......................................................................... 1
1.2. Features & Specifications .............................................................. 2
1.2.1. Features .............................................................................................. 2
1.2.2. Technical Specifications ................................................................... 2
1.2.3. Physical Specifications ...................................................................... 3
1.3. Terminology .................................................................................... 3
1.4. Package contents ............................................................................ 3
2. Installation ............................................................................. 4
2.1. Operating Environment ................................................................ 4
2.2. Connecting to network devices ................................................. 4
2.3. Connecting the power .................................................................. 4
3. Trouble Shooting ................................................................ 5
8PUG.book Page i Friday, August 9, 2002 5:32 PM
1. Introduction - 1
English
1. Introduction
1.1. Product Overview
This SP0005/SP0008/SP0016 high performance Fast Ethernet switch pro-
vides five/eight/sixteen Fast Ethernet ports to segment network traffic,
extend Fast Ethernet connection distance, and convert data packets
between different transmission speeds. This Fast Ethernet Switch pro-
vides shielded RJ-45 ports both with 10Base-T and 100Base-TX Auto-
negotiation capability and MDI/MDI-X auto crossover. All ports in this
switch support Full-Duplex and Half-Duplex operation modes. The Fast
Ethernet Switch is typically used to segment network traffic that can
improve the network performance by increasing the total bandwidth as
illustrated in Figure 1-1.
This Fast Ethernet Switch utilizes stored-and-forward switching architec-
ture that filters and forwards data after the complete data packet is
received and examined to be free of errors. With one set of status LEDs
for each individual port, the switch operation status can be easily moni-
tored. Their slim and compact design allows direct placing on the desktop
or conveniently mounted on the wall or the side of a desk to accommo-
date cabling consideration.
Figure 1-1
ADSL/Cable modem
Linux OS
Mac OS
Server
Windows Me/XP/NT
Windows 98/95/2000
8PUG.book Page 1 Friday, August 9, 2002 5:32 PM
1. Introduction - 2
English
1.2. Features & Specifications
1.2.1. Features
• Compliant with IEEE 802.3 10Base-T Ethernet and 802.3u 100Base-TX
Fast Ethernet Standards.
• Provides 5/8/16 ports for 10Base-T/100Base-TX, standard RJ-45
connectors.
• All RJ-45 ports supports 10Base-T/100Base-TX and Full-Duplex/Half-
Duplex Auto-negotiation function.
• Supports MDI/MDI-X auto crossover.
• Supports store-and-forward switching mechanism.
• Plug-and-Play.
• Performs non-blocking full wire speed rate.
• Supports up to 4K/2K/8K (5/8/16 ports) MAC addresses table / hashing
algorithm on address learning.
• Supports Aging function and 802.3x flow control for full Duplex and
collision-based backpressure function for half duplex operation.
• 128K/128K/512K (5/8/16 ports) Bytes buffer memory.
• Automatic address learning, address aging and address migration.
• Simple and economical way to bridge 10Base-T network and 100Base-
TX network.
• Front panel status LEDs.
• Desktop size.
• Wall mountable.
1.2.2. Technical Specifications
Ethernet Standards IEEE 802.3 10Base-T, 802.3u 100Base-TX
LED report
Power Steady Power On
Off Power Off
100 M
(Green)
Steady (LNK) A valid network connection established
Flashing (ACT) Transmitting or receiving data
10 M
(Yellow)
Steady (LNK) A valid network connection established
Flashing (ACT) Transmitting or receiving data
Cable 10Base-T: 2-pair UTP Cat. 3,4,5, up to 100m (328 ft)
100Base-TX: 2-pair UTP Cat. 5, up to 100m (328 ft)
Switching Method Store-and-forward
Forwarding Rate 14,880pps for 10Mbps; 148,800pps for 100Mbps
8PUG.book Page 2 Friday, August 9, 2002 5:32 PM
1. Introduction - 3
English
1.2.3. Physical Specifications
1.3. Terminology
PWR:
This Green LED lights when the power adapter is mounted.
LINK/ACT 10/100:
The Yellow LED lights when there is a valid 10-Base data linked on the
port. And Green LED lights for 100-Base data linked. LED lights blinking
when either 10-Base or 100-Base data is transmitted.
1.4. Package contents
The package should contain the following items:
SP0005/SP0008/SP0016 x 1
AC power adapter x 1
This User’s Guide
IF any item is found missing or damaged, please contact your local BenQ
reseller for replacement.
AC Input 50-60Hz, External power adapter
Operating Temperature 0°C ~ 50°C (32°F ~ 122°F )
Storage Temperature -20°C ~ 70°C (-4°F ~ 158°F )
Humidity 10% ~ 90% non-condensing
Emission Compliance
FCC part 15 Class B, CE Mark, VCCI Class B, C-TICK
for SP0005 & SP0008
FCC Class A, CE Mark, VCCI Class A, C-TICK
for SP0016
Safety UL/CSA
Dimension
162mm x 103mm x 32mm (SP0005)
162mm x 103mm x 32mm (SP0008)
301mm x 125mm x 32mm (SP0016)
Net Weight 250g (SP0005); 250g (SP0008); 540g (SP0016)
8PUG.book Page 3 Friday, August 9, 2002 5:32 PM
2. Installation - 4
English
2. Installation
2.1. Operating Environment
This switch must be installed and operated within the limits of specified
operating temperature and humidity (see previous section under Specifi-
cations).
• Do not place objects on top of the unit.
• Do not obstruct any vents at the sides of the unit.
• Do not position the unit near any heating source such as heater,
radiator, or direct exposure to sun.
• Prevent entering of water and moisture into the unit.
• If necessary, use dehumidifier to reduce humidity.
• Always avoid dust and dirt.
• Allow some space between the product and the surroundings to
facilitate dissipation of heat generated inside the switch.
2.2. Connecting to network devices
The RJ-45 ports on the switch are designed as MDI/MDI-X auto cross-
over ports which allow using straight-through cables to connect any port
on this switch to network device.
Connect one end of the network cable to the RJ-45 port on the rear
panel, and then connect the other end of the network cable to the RJ-45
port on the network device. Follow the same procedure to connect all
the RJ-45 ports of the switch. The UTP network cables must comply with
EIA/TIA 568 specifications and Category 5 standard for 100Mbps data
transmission and Category 3, 4, 5 for 10Mbps connection. Maximum
length, using UTP cable, between the switch and connected device is 100
meters (328ft). Once the network cable is connected to both ends and
the attached network device is powered on, the green LINK/ACT 10/100
LED should be lit (for 100-Base data linked by auto-negotiation).
2.3. Connecting the power
Connect the output end of the power adapter to the power connector
on the rear panel of the unit. Connect the power adapter to the power
outlet. The green Power LED on the front panel should be lit.
8PUG.book Page 4 Friday, August 9, 2002 5:32 PM
3. Trouble Shooting - 5
English
3. Trouble Shooting
The SP0005/SP0008/SP0016 can be easily monitored by its LED indica-
tors. Please follow the troubleshooting steps below to solve any problem
you may encounter during installation or implementation of the SP0005/
SP0008/SP0016.
1. Power LED is not lit
Check if the power cord is properly connected to the external power
adapter and the power outlet. Make sure the DC power jack is firmly
plugged into the power socket of the switch.
2. 100M Link/Activity(Green) is not lit when connect to
100 Mbps device
• Check the power switch of the network device attached to the switch;
make sure it is turned ON.
• Check the network cable; make sure it is properly connected to the
switch and the network device.
• Check the network cable; make sure the UTP cables comply with EIA/
TIA 568 and Category 5 specification.
Please perform the following tests
• Please check whether the RJ-45 cable is functional. Replace with
another working cable and see whether the condition can be improved.
• Use another port on the SP0005/SP0008/SP0016. If a link can be
established this way, the first port is faulty. Please contact your local
BenQ dealer for assistant.
• Make sure that all devices are connected to the network.
• Please ensure that the network adapter cards installed in the
workstation or other devices to the switch are in well working
condition.
[!] Contact your dealer if problem persists.
8PUG.book Page 5 Friday, August 9, 2002 5:32 PM
i
Inhalt
1. Einführung ............................................................................. 1
1.1. Produktübersicht ........................................................................... 1
1.2. Features & technische Daten ...................................................... 2
1.2.1. Features .............................................................................................. 2
1.2.2. Technische Daten ............................................................................. 2
1.2.3. Technische Daten ............................................................................. 3
1.3. Beschreibung ................................................................................... 3
1.4. Packungsinhalt ................................................................................. 3
2. Installation ............................................................................. 4
2.1. Betriebsumgebung ......................................................................... 4
2.2. Anschluss an Netzwerkgeräte .................................................... 4
2.3. Stromanschluss ............................................................................... 4
3. Problembehebung ............................................................... 5
8PUG.book Page i Wednesday, July 31, 2002 10:31 PM
1. Einführung - 1
Deutsch
1. Einführung
1.1. Produktübersicht
Dieser SP0005/SP0008/SP0016 High Performance Fast Ethernet Switch
bietet 5/8/16 Fast Ethernet-Schnittstellen für das Segmentieren von
Netzwerkverkehr, für das Erweitern der Fast Ethernet-
Verbindungsentfernung und für das Umwandeln von Datenpaketen in
unterschiedlichen Übertragungsgeschwindigkeiten. Dieser Fast Ethernet
Switch bietet abgeschirmte RJ-45-Schnittstellen mit sowohl 10Base-T als
auch 100Base-TX Auto-Negotiation-Kapazitäten und MDI/MDI-X-Auto-
Crossover. Alle Schnittstellen des Switches unterstützen die
Betriebsmodi Full-Duplex und Half-Duplex. Der Fast Ethernet Switch
wird normalerweise benutzt, um Netzwerkverkehr zu segmentieren und
so die Netzwerkleistung zu verbessern, indem die gesamte Bandbreite
erhöht wird. Siehe Abb. 1-1.
Der Fast Ethernet Switch benutzt einen "Stored-and-Forward"-
Umschaltmechanismus, der Daten filtert und weiter sendet, nachdem das
komplette Datenpaket empfangen und auf Fehler überprüft wurde. Jede
individuelle Schnittstelle besitzt einen eigenen Satz von Status-LEDs, so
dass der Status der Umschaltoperation leicht erkannt werden kann. Das
schmale und kompakte Gerät lässt sich direkt auf dem Schreibtisch
benutzen oder, abhängig von den Kabelanschlüssen, an einer Wand oder
der Seite eines Tisches anbringen.
Abb. 1-1
ADSL-/Kabelmodem
Betriebssystem Linux
Betriebssystem Mac
Server
Windows Me/XP/NT
Windows 98/95/2000
8PUG.book Page 1 Wednesday, July 31, 2002 10:31 PM
1. Einführung - 2
Deutsch
1.2. Features & technische Daten
1.2.1. Features
• Kompatibel mit IEEE 802.3 10Base-T Ethernet und 802.3u 100Base-TX
Fast Ethernet Standards.
• Bietet 5/8/16 Schnittstellen für 10Base-T/100Base-TX, Standard RJ-45
Anschlüsse.
• Alle RJ-45-Schnittstellen unterstützen 10Base-T/100Base-TX und Full-
Duplex/Half-Duplex Auto-Negotiation-Funktion.
• Unterstützt MDI/MDI-X Auto-Crossover.
• nterstützt "Store-and-Forward"-Umschaltmechanismus.
• Plug-and-Play
• Ermöglicht nicht blockierte volle Kabelgeschwindigkeiten.
• Unterstützt bis zu 4K/2K/8K (5/8/16 Schnittsellen) MAC-
Adressentabelle / Hashing-Algorithmus bei Adressen-Lernen.
• Unterstützt Aging-Funktion und 802.3x Flusskontrolle für Full-Duplex
und Kollision-basierte Backpressure-Funktion für Half-Duplex-
Operation.
• 128K/128K/512K (5/8/16 Schnittstellen) Bytes-Puffer-Speicher.
• Automatisches Adressen-Lernen, Adressen-Aging und Adressen-
Migration.
• Einfache und und sparsame Weise zum Überbrücken von 10Base-T-
Netzwerk und 100Base-TX-Netzwerk.
• Status-LEDs auf Vorderseite
• Schreibtischgröße.
• An Wand montierbar.
1.2.2. Technische Daten
Ethernet-Standards IEEE 802.3 10Base-T, 802.3u 100Base-TX
LED-Anzeige
Strom Ständig Strom ein
Aus Strom aus
100 M
(Grün)
Ständig (LNK) Eine gültige Netzwerkverbindung wurde
erstellt
Aufblinkend (ACT) Daten werden übertragen oder empfangen
10 M
(Gelb)
Ständig (LNK) Eine gültige Netzwerkverbindung wurde
erstellt
Aufblinkend (ACT) Daten werden übertragen oder empfangen
Kabel 10Base-T: 2-pair UTP Cat. 3,4,5, bis zu 100m (328 ft)
100Base-TX: 2-pair UTP Cat. 5, bis zu 100m (328 ft)
Umschaltmethode Store-and-Forward
Forwarding-Rate 14,880pps für 10Mbps; 148,800pps für 100Mbps
8PUG.book Page 2 Wednesday, July 31, 2002 10:31 PM
Andere Handbücher für SP0005
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Sprachen:
Andere BenQ Schalten Handbücher
